REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

    Click here

  4. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  5. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. B001WHCE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  6. REMOVE REAR DOOR UPPER ARMREST BASE PANEL LH

    Click here

  7. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

    Click here

  8. REMOVE ASSIST GRIP COVER LH


    1. B001VWK

      Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

  9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. B001ZDNE03

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tech Tips

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector and remove the rear door trim board sub-assembly LH.

    5. B001YOC

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  10. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. B001X1U

      Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.

      Note


      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  11. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. B001YC4

      Detach the 2 claws and remove the rear door inside handle sub-assembly LH.

  12. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. B001W4W

      Remove the 6 screws and rear door inside handle bezel LH.

  13. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)

    Click here

  14. REMOVE REAR SPEAKER SET (w/ Rear Speaker)

    Click here

  15. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A01X39W

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  16. REMOVE REAR DOOR PANEL PROTECTOR LH


    1. B001VOP

      Detach the claw and remove the rear door panel protector LH.

  17. REMOVE REAR DOOR GLASS RUN LH


    1. B001WKR

      Remove the rear door glass run LH from the window frame.

  18. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. B001ZYJ

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  19. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. B001WJP

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  20. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH


    1. Remove the rear door quarter window weatherstrip LH.

  21. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. B001YV8

      Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

      Note

      Do not damage the door glass.

  22. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)


    1. B001YBXE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the rear door glass channel sub-assembly LH.

      Note

      Be careful not to damage the door glass.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)


    1. Remove the rear door glass channel filler.

  24. REMOVE REAR DOOR FRAME GARNISH LH


    1. B001WA3

      Detach the clip and remove the rear door frame garnish LH.

      Tech Tips

      This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish LH.

  25. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH


    1. B001ZN8

      Detach the clip and remove the rear No. 2 door frame garnish LH.

      Tech Tips

      This clip needs to be replaced with a new one because the clip will break when removing the rear No. 2 door frame garnish LH.

  26. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. B001YHWE09
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.

    2. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note

      Be careful when removing the bolts as the motor may fall and become damaged.

    3. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  27. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

  28. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

    Click here

  29. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

    Click here

  30. REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

  31. REMOVE REAR DOOR LOCK ASSEMBLY LH

    Click here

  32. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B001Y0YE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B001ZBX

      Remove the rear door lock remote control cable assembly LH.

  33. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B001ZQ0E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B001XX5E03
      Text in Illustration
      *A w/o Double Lock
      *B w/ Double Lock

      Remove the rear door inside locking cable assembly LH.

  34. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH


    1. A01X0H8

      Using a T30 ''TORX'' socket, loosen the screw.

    2. A01X49A

      Detach the claw and remove the rear door outside handle cover LH.

  35. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A01WZF7

      Using a T30 "TORX" wrench, loosen the screw.

    2. w/ Entry and Start System:


      1. Disconnect the connector.

    3. A01X3IP

      Remove the rear door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

  36. REMOVE REAR NO. 1 DOOR OUTSIDE HANDLE PAD LH


    1. B001ZQ7

      Detach the 3 claws and remove the rear No. 1 door outside handle pad LH.

  37. REMOVE REAR NO. 2 DOOR OUTSIDE HANDLE PAD LH


    1. B001Z00

      Detach the 2 claws and remove the rear No. 2 door outside handle pad LH.

  38. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A01X8CB

      w/ Entry and Start System:


      1. Detach the clamp.

      2. Disconnect the connector.

    2. A01WZ5I

      Using a T30 ''TORX'' socket, loosen the screw.

    3. Slide the rear door outside handle frame sub-assembly LH and No. 4 electrical key wire harness to remove them.

      Tech Tips

      Remove the rear door outside handle frame sub-assembly LH through the service hole.

    4. Remove the lock open rod from the rear door outside handle frame sub-assembly LH.

  39. REMOVE NO. 4 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)


    1. A01X8J5

      Disconnect the connector.

    2. Detach the 2 clamps, and remove the No. 4 electrical key wire harness from the rear door outside handle frame sub-assembly LH.

  40. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)


    1. A01X17M

      Remove the screw and door electrical key oscillator.

  41. REMOVE REAR DOOR CHECK COVER LH (w/ Cover)


    1. A01X3B7

      Remove the rear door check cover LH.

  42. REMOVE REAR DOOR CHECK ASSEMBLY LH


    1. B001VO8

      Remove the bolt, 2 nuts and rear door check assembly LH.

      Note

      Be careful when removing the bolt and nuts as the rear door check assembly LH may fall and become damaged.

      Tech Tips

      Remove the rear door check assembly LH through the service hole.

  43. REMOVE REAR DOOR WEATHERSTRIP LH


    1. Detach the 21 clips and remove the rear door weatherstrip LH.

      B001ZSIE02
      Text in Illustration
      *A w/ Spot Cover *B w/o Spot Cover
      *1 Double-sided Tape - -