FRONT DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

    Click here

  4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH


    1. B001W1K

      Detach the clip and claw, and remove the front door lower frame bracket garnish LH.

  5. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

    Click here

  6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    1. B001XAEE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE FRONT UPPER ARMREST BASE PANEL LH

    Click here

  8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

    Click here

  9. REMOVE DOOR ASSIST GRIP COVER LH


    1. B001VX6

      Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. B001X1VE03

      Remove the 3 screws.

    2. Remove the 13 clips.

    3. Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tech Tips

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector.

    5. B001W8Y

      Disconnect the 2 cables from the front door inside handle sub-assembly LH.

  11. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH


    1. B001ZYE

      Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

      Note


      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  12. REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

    Click here

  13. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH


    1. B001XFK

      Detach the 2 claws and remove the front door inside handle sub-assembly LH.

  14. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH


    1. A01X95H

      Remove the 7 screws and front door inside handle bezel LH.

  15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  16. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)

    Click here

  17. REMOVE FRONT DOOR PANEL PROTECTOR LH


    1. B001WAO

      Remove the screw, and remove the front No. 1 door stiffener cushion and front door panel protector LH.

  18. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

  19. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

    Click here

  20. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. B001ZWB

      Using a clip remover, detach the 9 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the front door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  21. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Driver Side:

      Temporarily install the multiplex network master switch.

    2. Passenger Side:

      Temporarily install the power window regulator switch assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Move the front door glass sub-assembly until the bolts appear in the service holes.

    5. Disconnect the cable from the negative (-) battery terminal.

    6. B001ZAA

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    7. B001ZI6

      Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the front door glass sub-assembly upward.

      Note

      Be careful not to damage the glass.

    8. Driver Side:

      Remove the multiplex network master switch.

    9. Passenger Side:

      Remove the power window regulator switch assembly.

  22. REMOVE FRONT DOOR GLASS RUN LH


    1. B001W03

      Remove the front door glass run LH.

  23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH


    1. A01XAWA

      Remove the bolt and front door rear lower frame sub-assembly LH.

  24. REMOVE LOWER DOOR FRAME GARNISH LH


    1. B001Z99

      Detach the claw and remove the lower door frame garnish LH.

  25. REMOVE FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH

    Click here

  26. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

    Click here

  27. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. B001ZEUE16
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

    2. Remove the 5 bolts, and front door window regulator sub-assembly LH.

      Tech Tips

      Remove the front door window regulator sub-assembly LH through the service hole.

      Note

      Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.

    3. Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.

    4. Remove the temporary bolt from the front door window regulator sub-assembly LH.

  28. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Click here

  29. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    1. A01X80Y

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.

    3. A01X5X6

      Detach the 2 claws and remove the front door outside handle cover LH.

  30. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. A01X6QR

      w/ Entry and Start System:


      1. Disconnect the connector.

    2. Using a T30 "TORX" wrench, loosen the screw.

    3. A01XACT

      Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

      Note

      If the release plate is not pulled and held when removing the front door outside handle assembly LH, the release plate will interfere with the front door outside handle assembly LH and become damaged.

  31. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH


    1. A01X7PG

      Detach the 3 claws and remove the front door front outside handle pad LH.

  32. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH


    1. A01X2HE

      Detach the 2 claws and remove the front door rear outside handle pad LH.

  33. REMOVE FRONT DOOR LOCK ASSEMBLY LH

    Click here

  34. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. B001YNH

      Remove the front door lock remote control cable assembly LH.

  35. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. B001WO4E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B001W66

      Remove the front door inside locking cable assembly LH.

  36. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    1. A01X6IC

      Using a T30 "TORX" wrench, loosen the screw.

    2. A01X920

      Detach the 2 claws. Slide the front door outside handle frame sub-assembly LH and No. 2 electrical key wire harness to remove it.

      Tech Tips

      Remove the front door outside handle frame sub-assembly LH through the service hole.

  37. REMOVE NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)


    1. A01XAI4

      Disconnect the connector.

    2. Detach the 3 clamps and remove the wire harness from the front door outside handle frame sub-assembly.

  38. REMOVE FRONT DOOR LOCK OPEN ROD LH


    1. A01XAIM

      Remove the front door lock open rod LH.

  39. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)


    1. A01X3SM

      Remove the screw and door electrical key oscillator.

  40. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION


    1. B001W59

      Remove the 2 bolts.

    2. Detach the 2 clamps and front No. 2 door stiffener cushion.

  41. REMOVE FRONT DOOR CHECK COVER LH (w/ Cover)


    1. A01X31H

      Remove the front door check cover LH.

  42. REMOVE FRONT DOOR CHECK ASSEMBLY LH


    1. B001Z9Q

      Remove the bolt, 2 nuts and front door check assembly LH.

      Note

      Be careful when removing the bolt and nuts as the front door check assembly LH may fall and become damaged.

      Tech Tips

      Remove the front door check assembly LH through the service hole.

  43. REMOVE FRONT DOOR WEATHERSTRIP LH


    1. Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.

      B001XH8E02

      Tech Tips

      If clips are damaged during removal, replace them.

      Text in Illustration
      *A w/ Spot Cover *B w/o Spot Cover
      *1 Double-sided Tape - -