BACK DOOR INSPECTION

PROCEDURE

1. INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

   

   Text in Illustration

   *a	Component without harness connected (Back Door Remote Control Assembly)
   *b	Not pulled (off)
   *c	Pulled (on)

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition 1 - 2 Back door remote control is pulled (on) Below 1 Ω 1 - 2 Back door remote control is not pulled (off) 10 kΩ or higher

      If the result is not as specified, replace the back door remote control assembly.

2. INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Lower Tail Gate Lock Assembly LH)
      *b	Over-latch
      *c	Full-latch
      *d	Half-latch
      *e	Open-latch

      Operation check:

      
      

      1. Set the lower tail gate lock LH to the full-latch position.

      2. Apply battery voltage and check operation of the lower tail gate lock motor LH.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (ACT-) Battery negative (-) → Terminal 5 (ACT+) Latch turns to open-latch position

         If the result is not as specified, replace the lower tail gate lock assembly LH.

      3. Set the lower tail gate lock LH to the half-latch position.

      4. Apply battery voltage and check operation of the lower tail gate lock motor LH.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (ACT+) Battery negative (-) → Terminal 6 (ACT-) Latch turns to over-latch position

         If the result is not as specified, replace the lower tail gate lock assembly LH.

   2. 

      Text in Illustration

      *a	Component without harness connected (Lower Tail Gate Lock Assembly LH)
      *b	Over-latch
      *c	Full-latch
      *d	Half-latch
      *e	Open-latch

      Resistance check:

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Close Position Switch Tester Connection Condition Specified Condition 7 (HND) - 8 (GND) Over-latch Below 1 Ω 7 (HND) - 8 (GND) Full-latch 10 kΩ or higher 7 (HND) - 8 (GND) Half-latch 10 kΩ or higher 7 (HND) - 8 (GND) Open-latch 10 kΩ or higher

         If the result is not as specified, replace the lower tail gate lock assembly LH.

         Lower Tail Gate Courtesy Switch
         Tester Connection Condition Specified Condition 2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Half-latch Below 1 Ω 2 (FUL) - 3 (E1) Open-latch Below 1 Ω

         If the result is not as specified, replace the lower tail gate lock assembly LH.

         Half-latch Switch
         Tester Connection Condition Specified Condition 1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Full-latch Below 1 Ω 1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Open-latch Below 1 Ω

         If the result is not as specified, replace the lower tail gate lock assembly LH.

         Pawl Switch
         Tester Connection Condition Specified Condition 4 (POL) - 3 (E1) Over-latch 10 kΩ or higher 4 (POL) - 3 (E1) Full-latch Below 1 Ω 4 (POL) - 3 (E1) Half-latch Below 1 Ω 4 (POL) - 3 (E1) Open-latch 10 kΩ or higher

         If the result is not as specified, replace the lower tail gate lock assembly LH.

3. INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Lower Tail Gate Lock Assembly RH)
      *b	Over-latch
      *c	Full-latch
      *d	Half-latch
      *e	Open-latch

      Operation check:

      
      

      1. Set the lower tail gate lock RH to the full-latch position.

      2. Apply battery voltage and check operation of the lower tail gate lock motor RH.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (ACT-) Battery negative (-) → Terminal 5 (ACT+) Latch turns to open-latch position

         If the result is not as specified, replace the lower tail gate lock assembly RH.

      3. Set the lower tail gate lock RH to the half-latch position.

      4. Apply battery voltage and check operation of the lower tail gate lock motor RH.

         OK
         Measurement Condition Specified Condition Battery positive (+) → Terminal 5 (ACT+) Battery negative (-) → Terminal 6 (ACT-) Latch turns to over-latch position

         If the result is not as specified, replace the lower tail gate lock assembly RH.

   2. 

      Text in Illustration

      *a	Component without harness connected (Lower Tail Gate Lock Assembly RH)
      *b	Over-latch
      *c	Full-latch
      *d	Half-latch
      *e	Open-latch

      Resistance check:

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Close Position Switch Tester Connection Condition Specified Condition 7 (HND) - 8 (GND) Over-latch Below 1 Ω 7 (HND) - 8 (GND) Full-latch 10 kΩ or higher 7 (HND) - 8 (GND) Half-latch 10 kΩ or higher 7 (HND) - 8 (GND) Open-latch 10 kΩ or higher

         If the result is not as specified, replace the lower tail gate lock assembly RH.

         Lower Tail Gate Courtesy Switch
         Tester Connection Condition Specified Condition 2 (FUL) - 3 (E1) Over-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Full-latch 10 kΩ or higher 2 (FUL) - 3 (E1) Half-latch Below 1 Ω 2 (FUL) - 3 (E1) Open-latch Below 1 Ω

         If the result is not as specified, replace the lower tail gate lock assembly RH.

         Half-latch Switch
         Tester Connection Condition Specified Condition 1 (HAF) - 3 (E1) Over-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Full-latch Below 1 Ω 1 (HAF) - 3 (E1) Half-latch 10 kΩ or higher 1 (HAF) - 3 (E1) Open-latch Below 1 Ω

         If the result is not as specified, replace the lower tail gate lock assembly RH.

         Pawl Switch
         Tester Connection Condition Specified Condition 4 (POL) - 3 (E1) Over-latch 10 kΩ or higher 4 (POL) - 3 (E1) Full-latch Below 1 Ω 4 (POL) - 3 (E1) Half-latch Below 1 Ω 4 (POL) - 3 (E1) Open-latch 10 kΩ or higher

         If the result is not as specified, replace the lower tail gate lock assembly RH.