BACK DOOR DISASSEMBLY

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE BACK DOOR GRIP


    1. B002052

      Using a moulding remover, detach the 5 claws and open the cover.

    2. B001WTH

      Using a T30 "TORX" wrench, remove the 2 screws.

    3. Detach the claw and remove the back door grip.

  4. REMOVE LOWER BACK DOOR STOPPER CUSHION


    1. B001X19

      Remove the 4 bolts and 2 lower back door stopper cushions.

  5. REMOVE CENTER BACK DOOR GARNISH


    1. B001XWM

      Detach the 5 clips and 4 claws, and remove the center back door garnish.

    2. Disconnect the connector.

  6. REMOVE CENTER STOP LIGHT ASSEMBLY

    Click here

  7. REMOVE BACK DOOR SIDE GARNISH LH


    1. B001XQ6

      Detach the 3 clips and 2 claws, and remove the back door side garnish LH.

  8. REMOVE BACK DOOR SIDE GARNISH RH


    1. w/o Power Back Door:

      Tech Tips

      Use the same procedure described for the LH side.

    2. B001Z0C

      w/ Power Back Door:


      1. Detach the clip and 4 claws, and remove the back door side garnish RH.

  9. REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)


    1. B001XLNE02
      Text in Illustration
      *1 Power Back Door Rod
      *2 Hole of Back Door Service Hole Cover RH
      *a Back Door is Half-open

      Move the back door to a half-open position so that the hole in the center of the back door service hole cover RH is aligned lengthwise with the power back door rod.

    2. B001YKM

      Detach the 2 clips and separate the back door service hole cover RH, passing the power back door rod through the hole of the back door service hole cover RH.

      Note

      If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover RH, so do not perform this operation with the back door in a fully open position.

      Tech Tips

      If any of the clips have remained on the back door, remove the clips from the back door and install them to the back door service hole cover RH.

    3. B001ZY6

      Remove the ball joint bolt, power back door rod and back door stay plate.

    4. Remove the back door service hole cover RH from the power back door rod.

  10. REMOVE ASSIST GRIP (for Face to Face Seat Type)


    1. A01X4WB

      Remove the 2 screws and assist grip.

  11. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)


    1. A01WZHV

      Using a screwdriver, detach the 4 claws and remove the No. 2 back door service hole cover.

    2. Disconnect connector.

  12. REMOVE DOOR OPENING SWITCH SUB-ASSEMBLY (for Face to Face Seat Type)

    Click here

  13. REMOVE BACK DOOR GARNISH


    1. B001Z2K

      Using a clip remover, detach the 14 clips and remove the back door garnish.

  14. REMOVE REAR HEADER SPEAKER ASSEMBLY (for 14 Speakers)

    Click here

  15. REMOVE REAR ASSIST GRIP REINFORCEMENT (for Face to Face Seat Type)


    1. A01X6B1

      Remove the 3 bolts.

    2. Detach the 2 claws and remove the rear assist grip reinforcement.

  16. REMOVE POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

    Click here

  17. REMOVE POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

    Click here

  19. REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

    Click here

  20. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

    Click here

  21. REMOVE BACK DOOR LOCK COVER

    Click here

  22. REMOVE BACK DOOR LOCK ASSEMBLY

    Click here

  23. REMOVE DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)

    Click here

  24. REMOVE LICENSE PLATE LIGHT ASSEMBLY (for Standard)

    Click here

  25. REMOVE BACK DOOR OPENER SWITCH ASSEMBLY

    Click here

  26. REMOVE REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System or Rear View Monitor System)

    Click here

  27. REMOVE LIFT GATE WEATHERSTRIP


    1. B001W8N

      Detach the 25 clips and remove the lift gate weatherstrip.

      Note

      Do not pull strongly on the lift gate weatherstrip as it may tear.

  28. REMOVE CUSHION


    1. B001YZ1

      Remove the 2 cushions.

  29. REMOVE LOWER BACK DOOR STOPPER


    1. B001ZU2

      Remove the bolt and lower back door stopper.

  30. REMOVE REAR LIGHT ASSEMBLY LH

    Click here

  31. REMOVE REAR LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

    Click here

  33. REMOVE BACK DOOR GLASS CHANNEL LH (w/o Power Back Door)

    Click here

  34. REMOVE BACK DOOR GLASS CHANNEL RH (w/o Power Back Door)

    Tech Tips

    Use the same procedure described for the LH side.

  35. REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

    Click here

  36. REMOVE REAR WASHER NOZZLE (w/ Rear Wiper)

    Click here

  37. REMOVE BACK DOOR STAY ASSEMBLY LH

    Click here

  38. REMOVE BACK DOOR STAY ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    Click here

  40. REMOVE BACK DOOR TRIM COVER LH


    1. B001YG0

      Remove the back door trim cover LH as shown in the illustration.

  41. REMOVE BACK DOOR TRIM COVER RH


    1. B001Y55

      Remove the back door trim cover RH as shown in the illustration.

  42. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. B001YTU

      Remove the 4 bolts.

    2. Detach the 16 clips and remove the back door trim panel assembly.

  43. REMOVE NO. 2 BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY (w/ Tire Carrier)

    Click here

  44. REMOVE LICENSE PLATE LIGHT ASSEMBLY (w/ Tire Carrier)

    Click here

  45. REMOVE REAR LICENSE LIGHT COVER (w/ Tire Carrier)

    Click here

  46. REMOVE REAR BUMPER ASSEMBLY


    1. for Standard:


      1. Remove the rear bumper assembly Click here.

    2. w/ Towing Hitch:


      1. Remove the rear bumper assembly Click here.

    3. w/ Pintle Hook:


      1. Remove the rear bumper assembly Click here.

  47. REMOVE SPARE TIRE

  48. REMOVE LOWER BACK DOOR TORSION BAR ASSEMBLY


    1. B001VXB

      Remove the 4 bolts and lower back door torsion bar assembly.

  49. REMOVE BACK DOOR TORSION BAR GUIDE


    1. B001WX5

      Detach the 2 claws and remove the back door torsion bar guide.

  50. REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY


    1. B001XM5E04
      Text in Illustration
      *1 Back Door Handle Grommet

      Remove the screw and back door inside handle.

    2. Remove the back door handle grommet.

  51. REMOVE LOWER TAIL GATE LOCK ASSEMBLY RH


    1. w/o Power Back Door:


      1. B001WH8

        Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly RH.

      2. B00200W

        Disconnect the cable from the lower tail gate lock assembly RH.

    2. w/ Power Back Door:


      1. B001X0W

        Disconnect the connector.

      2. B001WUN

        Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly RH.

  52. REMOVE BACK DOOR REMOTE CONTROL ASSEMBLY


    1. w/o Power Back Door:


      1. B001Y1Z

        Remove the 2 screws.

      2. B001YX5

        Disconnect the left side cable.

      3. Remove the back door remote control assembly.

    2. w/ Power Back Door:


      1. B001WRR

        Disconnect the connector.

      2. Remove the 2 screws and back door remote control assembly.

  53. REMOVE LOWER TAIL GATE LOCK ASSEMBLY LH


    1. w/o Power Back Door:


      1. B001XNS

        Using a T30 "TORX" wrench, remove the 3 screws and lower tail gate lock assembly LH.

    2. w/ Power Back Door:


      1. B001W2E

        Disconnect the connector.

      2. B001X97

        Using a T30 "TORX" wrench, remove the 4 screws and lower tail gate lock assembly LH.

  54. REMOVE TAIL GATE STAY SUB-ASSEMBLY LH


    1. B001X1T

      Using a T40 "TORX" socket, remove the 2 screws and tail gate stay sub-assembly LH.

  55. REMOVE TAIL GATE STAY SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  56. REMOVE BACK DOOR DAMPER ASSEMBLY (w/ Power Back Door)


    1. B001WJF

      Remove the bolt and back door damper assembly.