TAIL GATE CLOSER SYSTEM, Diagnostic DTC:B225D

DTC Code DTC Name
B225D Tail Gate Panel Half Switch or Courtesy Switch LH

DESCRIPTION

The No. 2 main body ECU receives the half-latch switch, pawl switch and lower tail gate courtesy switch signals from the lower tail gate lock assembly LH and detects the open/closed status of the lower tail gate. DTC B225D is stored when the No. 2 main body ECU receives a half-latch switch, pawl switch or lower tail gate courtesy switch malfunction signal from the lower tail gate lock assembly LH.

DTC Code DTC Detection Condition Trouble Area
B225D A half-latch switch, pawl switch or lower tail gate courtesy switch malfunction (open or short circuit) signal from the lower tail gate lock LH is received.

  • Lower tail gate lock assembly LH

  • Harness or connector

  • No. 2 main body ECU

WIRING DIAGRAM

A01X7NCE02

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER


    1. Check the Data List for proper functioning of the half-latch switch, pawl switch and lower tail gate courtesy switch Click here.

      Body No. 4
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Half Latch Switch LH Half-latch switch signal / ON or OFF

      ON: Lower tail gate open

      OFF: Lower tail gate closed

      		 -
      Courtesy Switch LH Lower tail gate courtesy switch LH signal / ON or OFF

      ON: Lower tail gate open

      OFF: Lower tail gate closed

      		 -
      Luggage Pawl switch Pawl switch signal / ON or OFF

      ON: Lower tail gate lock motor operating

      OFF: Lower tail gate open or closed

      		 -
      OK
      The display is as specified in the normal condition.

    NG

    INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH Click here

    OK

  2. CHECK DTC OUTPUT


    1. Starting with the lower tail gate closed, open and close the lower tail gate 6 times.

    2. Check for DTCs Click here.

    3. Clear the DTCs Click here.

    4. Starting with the lower tail gate closed, open and close the lower tail gate 6 times.

    5. Recheck for DTCs Click here.

      OK
      DTC B225D is not output.

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE NO. 2 MAIN BODY ECU Click here

  3. INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH


    1. Remove the lower tail gate lock assembly LH Click here.

    2. Inspect the lower tail gate lock assembly LH Click here.


    NG

    REPLACE LOWER TAIL GATE LOCK ASSEMBLY LH Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (LOWER TAIL GATE LOCK ASSEMBLY LH - NO. 2 MAIN BODY ECU AND BODY GROUND)


    1. Disconnect the h5 lower tail gate lock assembly LH connector.

    2. Disconnect the L50 and L51 No. 2 main body ECU connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      h5-1 (HAF) - L51-9 (HAF) Always Below 1 Ω
      h5-2 (FUL) - L51-4 (FUL) Always Below 1 Ω
      h5-4 (POL) - L50-15 (POL) Always Below 1 Ω
      h5-3 (E1) - Body ground Always Below 1 Ω
      h5-1 (HAF) - Body ground Always 10 kΩ or higher
      h5-2 (FUL) - Body ground Always 10 kΩ or higher
      h5-4 (POL) - Body ground Always 10 kΩ or higher

    OK

    REPLACE NO. 2 MAIN BODY ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR