SLIDING ROOF HOUSING INSTALLATION

PROCEDURE


  1. INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY


    1. Temporarily install the housing with the 8 bolts (vehicle body side) and 8 nuts.

    2. Tighten the 8 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Tighten the 8 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      B001X36

  2. INSTALL SLIDING ROOF WEATHERSTRIP


    1. Install the sliding roof weatherstrip as follows:


      1. Position the joint of the sliding roof weatherstrip at the rear center.

      2. Align the alignment mark on the sliding roof weatherstrip with the middle marks at the corners of the sliding roof glass sub-assembly and install the sliding roof weatherstrip.

      3. Install the lip of the sliding roof weatherstrip firmly.

        B001XSSE01
        Text in Illustration
        *a Correct *b Incorrect
        *c Joint *d Vehicle Rear
        *e Alignment Mark *f Middle Mark

  3. INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    1. B001WLP

      Using a T25 "TORX" driver, temporarily install the glass with the 4 screws.

    2. Perform a level check.

      B001WOFE06
      *1 Even

      1. Check the difference in the level between the roof panel and the upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

        Standard
        Area Specified Condition
        A - A -1.5 to +1.5 mm (-0.0591 to +0.0591 in.)
        B - B
        C - C
        D - D -1.0 to +1.5 mm (-0.0394 to +0.0591 in.)

        Tech Tips

        "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

      2. Perform a gap check.

        Check the gap between the roof panel and roof glass.

        Note

        The gap must be even all around.

    3. B001WLP

      Tighten the 4 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. CHECK FOR WATER LEAK


    1. After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.

    2. If there are any leaks, readjust the sliding roof glass sub-assembly.

  5. INSTALL SLIDING ROOF SIDE GARNISH LH

    B001YTB

    1. Attach the 5 claws to install the sliding roof side garnish.

  6. INSTALL SLIDING ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  7. INSTALL REAR NO. 5 ROOF AIR DUCT


    1. B001ZCW

      Attach the 2 clips to install the duct.

  8. INSTALL REAR NO. 4 ROOF AIR DUCT

    Tech Tips

    Use the same procedures described for the No. 5 roof air duct.

  9. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH


    1. Install the curtain shield airbag Click here.

  10. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  11. INSTALL ROOF HEADLINING ASSEMBLY


    1. Install the roof headlining Click here.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  13. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.