BACK DOOR GLASS(for Double Swing Out Type) INSTALLATION

PROCEDURE


  1. CLEAN BACK DOOR GLASS


    1. Using a scraper, remove the damaged clips, moulding and adhesive sticking to the glass.

    2. Clean the outer circumference of the back door glass with non-residue solvent.

      Note


      • Do not touch the glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using new glass, clean the glass with non-residue solvent.

  2. INSTALL BACK WINDOW GLASS CLIP LH (for Outer)


    1. Apply Primer G to the back door glass LH where the clips will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 2 new clips.

    3. A01X60PE01
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Install the 2 back window glass clips to the back door glass LH at the locations shown in the illustration.

  3. INSTALL BACK WINDOW GLASS CLIP LH (for Inner)


    1. Apply Primer G to the back door glass LH where the clips will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 2 new clips.

    3. A01WZ62E01
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Install the 2 back window glass clips to the back door glass LH at the locations shown in the illustration.

  4. INSTALL NO. 1 BACK DOOR GLASS ADHESIVE DAM (for LH Side)


    1. Apply Primer G to the back door glass LH where the dams will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 2 new dams.

    3. A01X9LBE01
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Install the 2 No. 1 back door glass adhesive dams to the back door glass LH at the locations shown in the illustration.

  5. INSTALL BACK WINDOW OUTSIDE MOULDING (for LH Side)


    1. A01XBHKE02
      Text in Illustration
      *1 Primer G
      *a Backside
      *b Ceramic End Line

      Apply Primer G to the back door glass LH where the back window outside moulding will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

      Standard
      Area Specified Condition
      a 10.1 mm (0.398 in.)
      b 3.0 mm (0.118 in.)

    2. Remove the peeling paper from a new moulding.

    3. Install the back window outside moulding to the back door glass LH at the location shown in the illustration.

      A01X1DSE02
      Text in Illustration
      *a Backside - -
      Standard
      Area Specified Condition
      a 10.1 mm (0.398 in.)
      b 6.1 mm (0.240 in.)
      c 4.6 mm (0.181 in.)

  6. INSTALL BACK DOOR GLASS ADHESIVE DAM (for LH Side)


    1. A01X0FXE02
      Text in Illustration
      *1 Primer G
      *a Backside
      *b Ceramic End Line

      Apply Primer G to the back door glass LH where the back door glass adhesive dam will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

      Standard
      Area Specified Condition
      a 11.0 mm (0.433 in.)
      b 3.0 mm (0.118 in.)

    2. Remove the peeling paper from a new dam.

    3. Install the back door glass adhesive dam to the back door glass LH at the location shown in the illustration.

      A01X4OSE02
      Text in Illustration
      *a Backside - -
      Standard
      Area Specified Condition
      a 5.8 mm (0.228 in.)
      b 7.0 mm (0.276 in.)
      c 6.8 mm (0.268 in.)

  7. INSTALL BACK DOOR GLASS LH


    1. A01XA5KE01
      Text in Illustration
      *1 Matchmark

      Position the glass.


      1. Using suction cups, place the glass in the correct position.

      2. Check that the entire contact surface of the back door glass rim is perfectly even.

      3. Place matchmarks on the back door glass and back door at the locations indicated in the illustration.

        Tech Tips


        • Placing matchmarks is only necessary when installing new back door glass. When reinstalling the used back door glass, matchmarks should already be present.

        • When reusing the glass, check and correct the matchmark positions.

        Note

        Check that the stoppers are attached to the back door correctly.

      4. Using suction cups, remove the back door glass.

    2. A01X0K5E02
      Text in Illustration
      *1 Primer M
      *2 Adhesive
      *a CORRECT
      *b INCORRECT

      Using a brush or sponge, apply Primer M to the exposed part of the back door.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Do not apply primer to the adhesive.

      • Throw away any leftover primer.

      • Do not apply too much primer.

    3. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

      A01X99ME03
      Text in Illustration
      *1 Primer G - -
      *a Backside *b Ceramic End Line
      Standard
      Area Specified Condition
      a 15.3 mm (0.602 in.)
      b 3.0 mm (0.118 in.)
      c 20.0 mm (0.787 in.)
      d 17.0 mm (0.669 in.)
      e 29.0 mm (1.14 in.)
      f 37.0 mm (1.46 in.)

      Tech Tips

      If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

    4. Apply adhesive to the back door glass LH.

      Adhesive
      Toyota Genuine Windshield Glass Adhesive or equivalent

      1. Cut off the tip of a cartridge nozzle as shown in the illustration below.

        Tech Tips

        After cutting off the tip, use all adhesive within the time written in the table below.

        Usage Time Frame
        Temperature Usage Time Frame
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour 40 minutes
        5°C (41°F) 8 hours

      2. Load a sealer gun with the cartridge.

      3. Apply adhesive to the back door glass LH as shown in the illustration.

        A01XAD8E02
        Text in Illustration
        *1 Adhesive *2 Adhesive Center Line
        *3 Ceramic Notch - -
        *a Backside - -
        Standard
        Area Specified Condition
        a 12.0 mm (0.472 in.)
        b 8.0 mm (0.315 in.)
        c 11.3 mm (0.445 in.)
        d 16.0 mm (0.630 in.)
        e 13.0 mm (0.512 in.)
        f 25.0 mm (0.984 in.)

    5. Install the back door glass LH to the vehicle body.


      1. Hold the back door glass securely in place with tape or equivalent until the adhesive has hardened.

        Note


        • Allow the primer coating to dry for 3 minutes or more.

        • Check that the clips are attached to the vehicle body correctly.

        • Check the clearance between the vehicle body and glass.

      2. Lightly press the outer surface of the back door glass to ensure that the back door glass is securely attached to the vehicle body.

      3. B001XF2E02
        Text in Illustration
        *1 Adhesive

        Using a scraper, remove any excess or protruding adhesive.

        Tech Tips

        Apply adhesive to any areas where the amount of adhesive is inadequate.

        Note

        Do not drive the vehicle within the time written in the table below.

        Minimum Time
        Temperature Minimum Time Prior to Driving Vehicle
        35°C (95°F) 1 hour 30 minutes
        20°C (68°F) 5 hours
        5°C (41°F) 24 hours

      4. Connect the connectors.

  8. CLEAN BACK DOOR GLASS RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL BACK WINDOW GLASS CLIP RH (for Outer)


    1. A01X29TE02
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Apply Primer G to the back door glass RH where the clips will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 2 new clips.

    3. Install the 2 back window glass clips to the back door glass RH at the locations shown in the illustration.

  10. INSTALL BACK WINDOW GLASS CLIP RH (for Inner)


    1. Apply Primer G to the back door glass RH where the clips will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 2 new clips.

    3. A01XB2LE01
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Install the 2 back window glass clips to the back door glass RH at the locations shown in the illustration.

  11. INSTALL NO. 1 BACK DOOR GLASS ADHESIVE DAM (for RH Side)


    1. Apply Primer G to the back door glass RH where the dams will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

    2. Remove the peeling paper from 3 new dams.

    3. A01XADGE01
      Text in Illustration
      *1 Ceramic Notch
      *a Backside

      Install the 3 No. 1 back door glass adhesive dams to the back door glass RH at the locations shown in the illustration.

  12. INSTALL BACK WINDOW OUTSIDE MOULDING (for RH Side)


    1. A01XB8VE02
      Text in Illustration
      *1 Primer G
      *a Backside
      *b Ceramic End Line

      Apply Primer G to the back door glass RH where the back window outside moulding will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

      Standard
      Area Specified Condition
      a 10.1 mm (0.398 in.)
      b 3.0 mm (0.118 in.)

    2. Remove the peeling paper from a new moulding.

    3. Install the back window outside moulding to the back door glass RH at the location shown in the illustration.

      A01X0XUE02
      Text in Illustration
      *a Backside - -
      Standard
      Area Specified Condition
      a 10.1 mm (0.398 in.)
      b 5.7 mm (0.224 in.)
      c 4.6 mm (0.181 in.)

  13. INSTALL BACK DOOR GLASS ADHESIVE DAM (for RH Side)


    1. A01XAJWE01
      Text in Illustration
      *1 Primer G
      *a Backside
      *b Ceramic End Line

      Apply Primer G to the back door glass RH where the back window outside moulding will be installed.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

      Tech Tips

      If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.

      Standard
      Area Specified Condition
      a 11.0 mm (0.433 in.)
      b 3.0 mm (0.118 in.)

    2. Remove the peeling paper from a new moulding.

    3. Install the back window outside moulding to the back door glass RH at the location shown in the illustration.

      A01WYV4E02
      Text in Illustration
      *a Backside *b R End
      Standard
      Area Specified Condition
      a 2.8 mm (0.110 in.)
      b 6.8 mm (0.268 in.)

  14. INSTALL BACK DOOR GLASS RH


    1. A01X6TCE01
      Text in Illustration
      *1 Matchmark

      Position the glass.


      1. Using suction cups, place the glass in the correct position.

      2. Check that the entire contact surface of the back door glass rim is perfectly even.

      3. Place matchmarks on the back door glass and back door at the locations indicated in the illustration.

        Tech Tips


        • Placing matchmarks is only necessary when installing new back door glass. When reinstalling the used back door glass, matchmarks should already be present.

        • When reusing the glass, check and correct the matchmark positions.

        Note

        Check that the stoppers are attached to the back door correctly.

      4. Using suction cups, remove the back door glass.

    2. A01X6PNE01
      Text in Illustration
      *1 Primer M
      *2 Adhesive
      *a CORRECT
      *b INCORRECT

      Using a brush or sponge, apply Primer M to the exposed part of the back door.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Do not apply primer to the adhesive.

      • Throw away any leftover primer.

      • Do not apply too much primer.

    3. Using a brush or sponge, apply Primer G to the contact surface of the back door glass.

      A01X0GSE03
      Text in Illustration
      *1 Primer G - -
      *a Backside *b Ceramic End Line
      Standard
      Area Specified Condition
      a 3.0 mm (0.118 in.)
      b 37.0 mm (1.46 in.)
      c 29.0 mm (1.14 in.)
      d 17.0 mm (0.670 in.)
      e 20.0 mm (0.787 in.)

      Tech Tips

      If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.

      Note


      • Allow the primer to dry for 3 minutes or more.

      • Throw away any leftover primer.

      • Do not apply too much primer.

      • Do not apply primer outside the ceramic area.

    4. Apply adhesive to the back door glass RH.

      Adhesive
      Toyota Genuine Windshield Glass Adhesive or equivalent

      1. Cut off the tip of a cartridge nozzle as shown in the illustration below.

        Tech Tips

        After cutting off the tip, use all adhesive within the time written in the table below.

        Usage Time Frame
        Temperature Usage Time Frame
        35°C (95°F) 15 minutes
        20°C (68°F) 1 hour 40 minutes
        5°C (41°F) 8 hours

      2. Load a sealer gun with the cartridge.

      3. Apply adhesive to the back door glass RH as shown in the illustration.

        A01X8GLE01
        Text in Illustration
        *1 Adhesive *2 Adhesive Center Line
        *3 Ceramic Notch - -
        *a Backside - -
        Standard
        Area Specified Condition
        a 12.0 mm (0.472 in.)
        b 8.0 mm (0.315 in.)
        c 11.3 mm (0.445 in.)
        d 25.0 mm (0.984 in.)
        e 13.0 mm (0.512 in.)

    5. Install the back door glass RH to the vehicle body.


      1. Hold the back door glass securely in place with tape or equivalent until the adhesive has hardened.

        Note


        • Allow the primer coating to dry for 3 minutes or more.

        • Check that the clips are attached to the vehicle body correctly.

        • Check the clearance between the vehicle body and glass.

      2. Lightly press the outer surface of the back door glass to ensure that the back door glass is securely attached to the vehicle body.

      3. B001XF2E02
        Text in Illustration
        *1 Adhesive

        Using a scraper, remove any excess or protruding adhesive.

        Tech Tips

        Apply adhesive to any areas where the amount of adhesive is inadequate.

        Note

        Do not drive the vehicle within the time written in the table below.

        Minimum Time
        Temperature Minimum Time Prior to Driving Vehicle
        35°C (95°F) 1 hour 30 minutes
        20°C (68°F) 5 hours
        5°C (41°F) 24 hours

      4. Connect the connectors.

  15. CHECK FOR LEAK AND REPAIR


    1. Conduct a leak test after the adhesive has completely hardened.

    2. Seal any leaks with auto glass sealer.

  16. INSTALL BACK DOOR TRIM PANEL ASSEMBLY LH (for LH Side)

    Click here

  17. INSTALL DOOR INSIDE HANDLE BEZEL LH (for LH Side)

    Click here

  18. INSTALL ASSIST GRIP LH (for LH Side)

    Click here

  19. INSTALL BACK DOOR CENTER WEATHERSTRIP (for RH Side)

    Click here

  20. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

    Click here

  21. INSTALL BACK DOOR TRIM PANEL ASSEMBLY RH (for RH Side)

    Click here

  22. INSTALL BACK DOOR TRIM COVER RH (for RH Side)

    Click here

  23. INSTALL ASSIST GRIP RH (for RH Side)

    Click here

  24. INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

    Click here

  25. INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

    Click here

  26. INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

    Click here

  27. INSTALL SPARE TIRE (w/ Tire Carrier)