BACK WINDOW GLASS REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE CENTER BACK DOOR GARNISH

    Click here

  4. REMOVE BACK DOOR SIDE GARNISH LH

    Click here

  5. REMOVE BACK DOOR SIDE GARNISH RH

    Click here

  6. REMOVE ASSIST GRIP (for Face to Face Seat Type)

    Click here

  7. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)

    Click here

  8. REMOVE POWER BACK DOOR MAIN SWITCH (for Face to Face Seat Type)

    Click here

  9. REMOVE BACK DOOR GARNISH

    Click here

  10. REMOVE BACK DOOR GLASS CHANNEL LH (w/ Rear Spoiler)

    A01X664

    1. Using a clip remover, remove the clip.

    2. Remove the back door glass channel LH.

  11. REMOVE BACK DOOR GLASS CHANNEL RH (w/ Rear Spoiler)

    A01X6U2

    1. Using a clip remover, remove the clip.

    2. Remove the back door glass channel RH.

  12. REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)

    Click here

  13. REMOVE REAR WIPER ARM (w/ Rear Wiper)

    Click here

  14. REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

    Click here

  15. REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

    Click here

  16. REMOVE BACK WINDOW MOULDING OUTSIDE LH

    A01XAVME02
    *1 Cut

    1. Using a knife, cut off the moulding as shown in the illustration.

      Note

      Be careful not to damage the vehicle body.

    2. Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

  17. REMOVE BACK WINDOW MOULDING OUTSIDE

    A01WZ5KE01
    *1 Cut

    1. Using a knife, cut off the moulding as shown in the illustration.

      Note

      Be careful not to damage the vehicle body.

    2. Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

  18. REMOVE BACK WINDOW GLASS


    1. A01X74PE02
      *1 Protective Tape

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

      Note

      When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

    2. Disconnect the connectors.

    3. A01X7N0E04
      *1 Clip
      *2 Piano Wire
      *3 Spacer

      From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.

      Note

      Make sure not to damage the wire harness.

    4. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    5. A01X2UVE02
      *1 Matchmark

      Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

      Tech Tips

      Matchmarks do not need to be placed if the glass is not going to be reused.

    6. Cut through the adhesive by pulling the piano wire around the back window glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the back window glass.

    7. A01XBTWE01
      *1 Matchmark

      Using suction cups, remove the back window glass.

  19. CLEAN VEHICLE BODY

    B001ZPAE11
    *1 Adhesive

    1. Using a scraper, remove the moulding and adhesive from the back window glass.

    2. Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

        Note

        Be careful not to damage the vehicle body.

      2. Clean the contact surface of the vehicle body with cleaner.

        Tech Tips

        Even if all the adhesive has been removed, clean the vehicle body.