WINDSHIELD GLASS REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  4. REMOVE FRONT FENDER MAIN SEAL LH

    Click here

  5. REMOVE FRONT FENDER MAIN SEAL RH

    Click here

  6. REMOVE FRONT WIPER ARM LH

    Click here

  7. REMOVE FRONT WIPER ARM RH

    Click here

  8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  9. REMOVE WINDSHIELD OUTSIDE MOULDING LH


    1. B001XXHE04

      Remove the windshield outside moulding.


      1. Put protective tape around the moulding.

      2. Using a moulding remover, detach the 6 clips and remove the moulding.

        Note


        • When removing the windshield outside moulding, be careful not to damage the roof drip side finish moulding clip labeled A in the illustration.

        • If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.

  10. REMOVE WINDSHIELD OUTSIDE MOULDING RH

    Tech Tips

    Use the same procedure as for the LH side.

  11. REMOVE NO. 4 WINDSHIELD MOULDING PAD


    1. B001WGE

      Remove the 4 No. 4 windshield moulding pads.

      Tech Tips

      Use the same procedure to remove the 4 pads on the other side.

  12. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedures if replacing any No. 3 windshield outside moulding clip(s).


    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

      Tech Tips

      Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. B001WUDE01
      *a 5 mm

      Lightly press the drill against the No. 3 windshield outside moulding clip(s), drill off the flanges of the No. 3 windshield outside moulding clip(s), and remove the No. 3 windshield outside moulding clip(s).

      Note


      • Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

      • Do not pry the No. 3 windshield outside moulding clips with the drill, because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.

      Note

      Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.

    4. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

      Tech Tips

      Use the same procedure to remove the clip(s) on the other side.

  13. REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP

    Tech Tips

    Perform the following procedures if replacing any roof drip side finish moulding clip.


    1. Remove the roof drip side finish moulding clips.

      Tech Tips

      Use the same procedure to remove the clip on the other side.

  14. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

    Click here

  15. REMOVE FRONT PILLAR GARNISH LH

    Click here

  16. REMOVE FRONT PILLAR GARNISH RH

    Click here

  17. REMOVE MAP LIGHT ASSEMBLY

    Click here

  18. REMOVE VISOR BRACKET COVER

    Click here

  19. REMOVE VISOR ASSEMBLY LH

    Click here

  20. REMOVE VISOR ASSEMBLY RH

    Click here

  21. REMOVE VISOR HOLDER

    Click here

  22. REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

    Click here

  23. REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Click here

  24. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  25. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

    Click here

  26. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

    Click here

  27. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  28. REMOVE RAIN SENSOR (w/ Rain Sensor)

    Click here

  29. REMOVE ROOF HEADLINING


    1. w/ Sliding Roof:


      1. Partially remove the roof headlining.

        Tech Tips

        It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

        Refer to the following procedures Click here.

    2. w/o Sliding Roof:


      1. Partially remove the roof headlining.

        Tech Tips

        It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

        Refer to the following procedures Click here.

  30. REMOVE WINDSHIELD OUTSIDE MOULDING


    1. B001W9WE01
      *1 Cut

      Using a knife, cut off the moulding as shown in the illustration.

      Note

      Be careful not to damage the vehicle body.

    2. Pull the shaded area shown in the illustration by hand to remove the windshield outside moulding.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

  31. REMOVE WINDSHIELD GLASS

    Tech Tips

    Be careful not to damage the wire harnesses near the windshield glass with the piano wire.


    1. B001YQKE01

      w/o Heated Windshield Defroster:


      1. Disconnect the connector A.

        Tech Tips

        w/o Heated Windshield Defroster:

        The vehicle only has connector A.

    2. w/ Heated Windshield Defroster:


      1. Disconnect the 3 connectors.

    3. B001VNKE01
      *1 Plastic Sheet
      *2 Protective Tape
      *3 Stopper
      *4 Piano Wire

      Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    4. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    5. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

      Note


      • When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      • To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.

    6. B001W9OE01
      *1 Matchmark

      Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

      Note

      Matchmarks do not need to be placed if not reusing the glass.

    7. Cut through the adhesive by pulling the piano wire around the glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the glass.

    8. Disconnect the stoppers.

    9. Using suction cups, remove the glass.

  32. REMOVE NO. 2 WINDSHIELD GLASS STOPPER


    1. Using a scraper, remove the 2 stoppers.

  33. REMOVE WINDSHIELD GLASS ADHESIVE DAM


    1. Using a scraper, remove the dam.

  34. REMOVE FRONT INNER WINDOW MOULDING COVER LH


    1. Using a scraper, remove the cover.

  35. CLEAN WINDSHIELD GLASS


    1. B001Y0A

      Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.

    2. Clean the outer circumference of the glass with non-residue solvent.

      Note


      • Do not touch the glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using new glass, clean the glass with non-residue solvent.

  36. REMOVE WINDSHIELD GLASS STOPPER


    1. Remove the 2 windshield glass stoppers.

  37. CLEAN VEHICLE BODY


    1. B001ZPAE11
      *1 Adhesive

      Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with cleaner.

      Tech Tips

      Even if all the adhesive has been removed, clean the vehicle body.