POWER WINDOW REGULATOR MOTOR(for Rear Door) INSPECTION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on 4 Windows)

   Note

   
   

   • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

   • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
      *b	Motor Gear
      *c	Clockwise
      *d	Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      OK

      Measurement Condition Specified Condition Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP). After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec. Motor gear rotates clockwise (UP) Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN). After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec. Motor gear rotates counterclockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly LH

2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on 4 Windows)

   Note

   
   

   • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

   • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Power Window Regulator Motor Assembly RH)
      *b	Motor Gear
      *c	Clockwise
      *d	Counterclockwise

      Check that the motor gear rotates smoothly as follows.

      OK

      Measurement Condition Specified Condition Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP). After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec. Motor gear rotates counterclockwise (UP) Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN). After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec. Motor gear rotates clockwise (DOWN)

      If the result is not as specified, replace the power window regulator motor assembly RH

3. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Models with Jam Protection Function on Driver Door Window Only)

   
   
   1. 

      Text in Illustration

      *1	Motor Gear
      *a	Component without harness connected (Rear Power Window Regulator Motor Assembly LH)
      *b	Clockwise
      *c	Counterclockwise

      Check the operation of the regulator motor.

   2. Apply battery voltage to the regulator motor and check the operation of the regulator motor.

      OK
      Measurement Condition Specified Condition Battery positive (+)→Terminal 1 Battery negative (-)→Terminal 2 Motor gear rotates clockwise Battery positive (+)→Terminal 2 Battery negative (-)→Terminal 1 Motor gear rotates counterclockwise

      
      

      • If the result is not as specified, replace the rear power window regulator motor assembly LH.

        Text in Illustration

        *1	Motor Gear
        *a	Component without harness connected (Rear Power Window Regulator Motor Assembly LH)
        *b	Clockwise
        *c	Counterclockwise

4. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Models with Jam Protection Function on Driver Door Window Only)

   
   
   1. 

      Text in Illustration

      *1	Motor Gear
      *a	Component without harness connected (Front Rear Window Regulator Motor Assembly RH)
      *b	Counterclockwise
      *c	Clockwise

      Check the operation of the regulator motor.

   2. Apply battery voltage to the regulator motor and check the operation of the regulator motor.

      OK
      Measurement Condition Specified Condition Battery positive (+)→Terminal 2 Battery negative (-)→Terminal 1 Motor gear rotates clockwise Battery positive (+)→Terminal 1 Battery negative (-)→Terminal 2 Motor gear rotates counterclockwise

      
      

      • If the result is not as specified, replace the rear power window regulator motor assembly RH.

        Text in Illustration

        *1	Motor Gear
        *a	Component without harness connected (Front Rear Window Regulator Motor Assembly RH)
        *b	Counterclockwise
        *c	Clockwise