ROOF HEADLINING(w/o Sliding Roof) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL SIDE TRIM BOX

    B001Z04

    1. Install the side trim box with the 9 screws.

  2. INSTALL SIDE TRIM BOX COVER


    1. Install the side trim box cover.

  3. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Install the quarter trim lid.

  4. INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    B001VOU

    1. Attach the 6 clips to install the quarter trim cover.

  5. INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  6. INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YAE

    1. Attach the 6 clips to install the rear No. 2 seat cover bezel.

  7. INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the rear No. 2 seat cover bezel.

  8. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

  9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  10. INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001Z9U

    1. Attach the 4 claws to install the cover.

  11. INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    Tech Tips

    Use the same procedures described for the LH side.

  12. INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001YPJ

    1. Attach the 4 claws to install the cover.

  13. INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    B001XGH

    1. Attach the 4 claws to install the cover.

    2. B001VTB

      Install the duct with the 6 screws.

  14. INSTALL TONNEAU COVER HANGER LH (w/ Tonneau Cover)

    B001Y7OE01
    *1 Rear Quarter Trim Base

    1. Install the tonneau cover hanger and rear quarter trim base with the 2 screws.

  15. INSTALL TONNEAU COVER HANGER RH (w/ Tonneau Cover)

    Tech Tips

    Use the same procedures described for the LH side.

  16. INSTALL TONNEAU COVER HOLDER BRACKET LH (w/ Tonneau Cover)

    A01XBVQE03
    *1 Front QuarterTrim Base

    1. Attach the 3 claws to install the tonneau cover holder bracket.

    2. Install the front quarter trim base with the 3 screws and then install the remaining 5 screws.

  17. INSTALL TONNEAU COVER HOLDER BRACKET RH (w/ Tonneau Cover)

    Tech Tips

    Use the same procedures described for the LH side.

  18. INSTALL NO. 2 CUP HOLDER

    B001ZNB

    1. Attach the 3 claws to install the cup holder.

    2. Install the 5 screws.

  19. INSTALL NO. 1 CUP HOLDER

    B001WBA

    1. Attach the 3 claws to install the cup holder.

    2. Install the 5 screws.

  20. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH

    B001ZDA

    1. Attach the 4 claws to install the quarter trim cover.

    2. Install the 7 screws.

    3. B002038

      w/ Rear Heater:

      Install the duct with the 8 screws.

  21. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH

    B001Y7R

    1. Attach the 4 claws to install the quarter trim cover.

    2. Install the 7 screws.

  22. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH

    B001Z0KE01
    *1 Spring Nut

    1. Install the hanger with 2 new spring nuts.

  23. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedures described for the LH side.

  24. INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001ZV4E01
    *1 Spring Nut

    Tech Tips

    Use the same procedure to install the hanger on the other side.


    1. Install the hanger with 2 new spring nuts.

  25. INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YIH

    1. Attach the 7 claws to install the cover.

  26. INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  27. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001ZQX

    1. Attach the 6 claws to install the plate.

  28. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  29. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001VUZ

    1. Slide the plate in the direction shown in the illustration and attach the 6 claws to install the plate.

  30. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  31. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    B001X9U

    1. Attach the 3 clips to install the rear door scuff plate outside.

  32. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  33. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    B001WTM

    1. Attach the 4 clips to install the front door scuff plate outside.

  34. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  35. INSTALL BACK DOOR WEATHERSTRIP

    A01X5B5E04
    *1 Alignment Mark
    *2 Mark

    1. Install the back door weatherstrip as shown in the illustration.

  36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01X56TE05
    *1 Alignment Mark
    *2 Mark

    1. Install the rear door opening trim weatherstrip as shown in the illustration.

  37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  38. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01X5BHE04
    *1 Alignment Mark
    *2 Mark

    1. Install the front door opening trim weatherstrip as shown in the illustration.

  39. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  40. INSTALL ROOF HEADLINING ASSEMBLY

    B001VZ6

    Tech Tips


    • for Manual Seat:

      When installing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.

    • for Power Seat:

      When installing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • for Power Seat:

      After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. B001Y37

      Place the headlining in the cabin from the rear of the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. for 3 Person Seat Type Rear No. 2 Seat:

      Attach the 2 guides, 12 claws and 2 clips to install the headlining.

      B001YMHE01
      *1 for 3 Person Seat Type Rear No. 2 Seat:

    3. except 3 Person Seat Type Rear No. 2 Seat:

      Attach the 2 guides, 12 claws and 3 clips to install the headlining.

      B001W8CE01
      *1 except 3 Person Seat Type Rear No. 2 Seat:
    4. B001ZFTE04
      *1 Rear Left Side

      w/ Rear Wiper:

      Connect the washer hose.

    5. B001YHCE03
      *1 Rear Right Side

      Connect the antenna cord connector.

    6. B001YJCE01
      *1 Front Right Side

      Connect the antenna cord connector and attach the 2 clamps.

    7. Install the bolt.

    8. B001YUQE03
      *1 Front Left Side
      *2 Washer Hose

      Connect the 3 roof wire connectors and 4 clamps.

    9. w/ Rear Wiper:

      Connect the washer hose.

    10. A01XAR5

      w/ Rain Sensor:

      Connect the rain sensor connector.

    11. A01X2WE

      w/ EC Mirror:

      Connect the inner mirror connector.

  41. INSTALL FRONT ROOF SIDE RAIL GARNISH LH

    A01X39TE03
    *1 New Clip

    1. Install 3 new clips to the roof side rail garnish.

    2. Attach the 3 clips to install the roof side rail garnish.

  42. INSTALL FRONT ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  43. INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001W2K

    Tech Tips

    Use the same procedure to install the 3rd seat assist grip on the other side.


    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.

  44. INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH

    B001ZEW

    1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

      Install the No. 2 assist grip assembly.


      1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

      2. Install the assist grip.

    2. B001W2K

      w/ Rear No. 2 Seat, for Face to Face Seat Type:

      Install the No. 2 assist grip assembly.


      1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

      2. Install the assist grip.

  45. INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  46. INSTALL ASSIST GRIP ASSEMBLY

    B001W2K

    Tech Tips

    Use the same procedure to install the assist grip on the other side.


    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.

  47. INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

    B001ZD9

    1. Attach the 4 guides and 4 clips to install the seat belt anchor cover.

  48. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  49. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  50. INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

    B001VS8

    1. Attach the 2 clips to install the center visor.

  51. INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Tech Tips

    Use the same procedures described for the LH side.

  52. INSTALL VISOR HOLDER

    B001XFW

    Tech Tips

    Use the same procedures to install the visor holder on the other side.


    1. Attach the 2 claws.

    2. Push the visor holder in to install it.

  53. INSTALL VISOR ASSEMBLY LH

    B002003

    1. Install the visor with the 2 screws.

  54. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  55. INSTALL VISOR BRACKET COVER

    B001ZTF

    Tech Tips

    Use the same procedure to install the visor bracket cover on the other side.


    1. Attach the 4 claws to install the visor bracket cover.

  56. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

    A01X6BS

    1. Install the 2 covers.

    2. A01XATT

      Attach the 4 claws to install the room light lens.

    3. B001WL1E02
      *1 Room Light Switch Base

      Attach the 4 claws to install the room light to the room light switch base.

    4. A01X4GJ

      Attach the 4 claws to install the room light.

  57. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    A01WZOA

    1. w/ Map Light:

      Install the No. 1 room light assembly.


      1. Connect the connector.

      2. Attach the 4 clips to install the room light.

    2. w/o Map Light:

      Install the No. 1 room light assembly.


      1. A01X6BS

        Install the 2 covers.

      2. A01XATT

        Attach the 4 claws to install the room light lens.

      3. B001WL1E02
        *1 Room Light Switch Base

        Attach the 4 claws to install the room light to the room light switch base.

      4. A01X4GJ

        Attach the 4 claws to install the room light.

  58. INSTALL MAP LIGHT ASSEMBLY (w/ Map Light)


    1. Connect the connector.

    2. Attach the 2 clips and 2 guides to install the map light.

    3. Install the 2 screws.

    4. Attach the 2 claws to close the 2 covers.

      A01WZKO

  59. INSTALL REAR UPPER PILLAR GARNISH LH

    B001YLH

    1. Attach the 5 clips to install the rear upper pillar garnish.

    2. B001XKP

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Install the seat belt shoulder anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      2. B001Y54

        Attach the 2 claws to close the seat belt shoulder anchor cover.

  60. INSTALL REAR UPPER PILLAR GARNISH RH

    B001ZJF

    1. w/o Power Back Door:


      1. Attach the 5 clips to install the rear upper pillar garnish.

    2. A01X3F8E04
      *1 Power Back Door Rod

      w/ Power Back Door:


      1. Pass the power back door rod through the rear upper pillar garnish.

      2. Attach the 5 clips to install the rear upper pillar garnish.

    3. B001WBK

      Install the seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. B001Y91

      Attach the 2 claws to close the seat belt shoulder anchor cover.

  61. INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

    Click here

  62. INSTALL BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

    Click here

  63. INSTALL CENTER BACK DOOR GARNISH (w/ Power Back Door)

    Click here

  64. INSTALL REAR FRONT QUARTER TRIM GARNISH LH

    B001X8C

    1. Pass the seat belt anchor through the quarter trim garnish.

    2. Attach the clip and 2 guides to install the quarter trim garnish.

    3. Install the screw.

  65. INSTALL REAR FRONT QUARTER TRIM GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  66. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B001XME

    Tech Tips

    When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. w/o Rear Air Conditioning System:

        Connect the rear seat lock control lever cable.

      2. w/ Rear Air Conditioning System:

        Connect the thermistor connector and rear seat lock control lever cable.

      3. Attach the 18 clips and 2 claws to install the quarter trim panel.

      4. Install the clip and bolt.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }
        B001WZM

    2. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Attach the 18 clips and 2 claws to install the quarter trim panel.

      2. Install the clip.

        B001XJ5

    3. w/ Tonneau Cover:


      1. Attach the 18 clips and 2 claws to install the quarter trim panel.

      2. Install the screw and clip.

        B001ZG2
    4. A01XA0XE05
      *1 Protruding Part

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    5. B001YLX

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    6. B001Z6R

      Attach the 3 claws to install the cover.

  67. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    B001X5H

    Tech Tips

    When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. w/o Rear Air Conditioning System:

        Connect the rear seat lock control lever cable.

      2. w/ Rear Air Conditioning System:

        Connect the thermistor connector and rear seat lock control lever cable.

      3. Attach the 16 clips and 2 claws to install the quarter trim panel.

      4. Install the clip and bolt.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }
        B001XI2

    2. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Attach the 16 clips and 2 claws to install the quarter trim panel.

      2. Install the clip.

        B001WA2

    3. w/ Tonneau Cover:


      1. Attach the 16 clips and 2 claws to install the quarter trim panel.

      2. Install the screw and clip.

        B001Z86
    4. B00201O

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Install the rear No. 2 seat belt anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      2. B001W3C

        Attach the 3 claws to install the cover.

    5. B001YAN

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    6. B001ZAG

      Attach the 3 claws to install the cover.

  68. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    A01WYVZ

    Tech Tips

    Use the same procedure to install the rear seat cover cap on the other side.


    1. Attach the 3 claws to install the rear seat cover cap.

  69. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

    B001WHB

    Tech Tips

    Use the same procedure to install the tonneau cover holder cap on the other side.


    1. Attach the 2 claws to install the tonneau cover holder cap.

  70. INSTALL CENTER PILLAR GARNISH LH

    B001WRF

    1. Pass the seat belt anchor through the center pillar garnish.

    2. Attach the 2 clips and 2 guides to install the center pillar garnish.

    3. Install the bolt.

  71. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  72. INSTALL REAR ASSIST GRIP ASSEMBLY

    B001VUB

    Tech Tips

    Use the same procedure to install the rear assist grip on the other side.


    1. Attach the 2 claws to install the rear assist grip.

    2. Install the 2 bolts.

    3. B001WIF

      Attach the 4 claws to install the 2 assist grip plugs.

  73. INSTALL CENTER LOWER PILLAR GARNISH LH

    Tech Tips


    • for Manual Seat:

      When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001Z8X

      Attach the 2 claws and 7 clips to install the center lower pillar garnish.

    2. B001Y3K

      Install the seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  74. INSTALL CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  75. INSTALL CENTER PILLAR GARNISH COVER LH

    Tech Tips


    • for Manual Seat:

      When installing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001XP8

      Attach the 2 clips and 2 guides to install the cover.

  76. INSTALL CENTER PILLAR GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  77. INSTALL FRONT PILLAR GARNISH LH

    B001Z6Z

    1. for 9, 14 Speakers:

      Connect the speaker connector.

    2. Attach the clip and 3 guides to install the front pillar garnish.

  78. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  79. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

    B001XJZ

    Tech Tips

    Use the same procedure to install the front assist grip on the other side.


    1. Attach the 2 claws to install the front assist grip.

    2. Install the 2 bolts.

    3. B001Y9H

      Attach the 4 claws to install the 2 assist grip plugs.

  80. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    B001WTN

    1. Attach the 6 clips to install the support plate.

  81. INSTALL REAR DOOR SCUFF PLATE LH

    B001Z1V

    1. Attach the 3 claws and 4 clips to install the scuff plate.

    2. Install the screw.

  82. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  83. INSTALL REAR STEP COVER

    B001ZUZ

    Tech Tips

    Use the same procedure to install the step cover on the other side.


    1. Attach the 2 claws to install the step cover.

  84. INSTALL FRONT DOOR SCUFF PLATE LH

    B001ZKS

    1. Attach the 7 claws and 4 clips to install the scuff plate.

  85. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  86. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)


    1. Install the rear No. 2 seat assembly LH Click here.

  87. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  88. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)


    1. Install the rear No. 2 seat assembly LH Click here.

  89. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  90. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  91. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.