ROOF HEADLINING(w/o Sliding Roof) REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  4. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)

    Click here

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)

    Click here

  7. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  8. REMOVE FRONT DOOR SCUFF PLATE LH

    B001ZKS

    1. Detach the 7 claws and 4 clips, and remove the front door scuff plate LH.

  9. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  10. REMOVE REAR STEP COVER

    Tech Tips

    Use the same procedure for both rear step covers.


    1. B001ZUZ

      Detach the 2 claws and remove the rear step cover.

  11. REMOVE REAR DOOR SCUFF PLATE LH

    B001Z1V

    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the rear door scuff plate LH.

  12. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    B001WTN

    1. Detach the 6 clips and remove the rear floor mat support plate.

  14. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip sub-assemblies.


    1. B001Y9H

      Detach the 4 claws and remove the 2 assist grip plugs.

    2. B001XJZ

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the assist grip sub-assembly.

  15. REMOVE FRONT PILLAR GARNISH LH

    B001Z6Z

    1. Detach the clip 3 guides, and remove the front pillar garnish LH.

    2. w/ Speaker:

      Disconnect the speaker connector and then remove the front pillar garnish.

    3. B001ZGRE04
      Text in Illustration
      *a Adhesive Tape
      *b Protective Cover
      *c Curtain Shield Airbag Assembly LH

      Protect the curtain shield airbag.


      1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  16. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. REMOVE CENTER PILLAR GARNISH COVER LH

    Tech Tips


    • for Manual Seat:

      When removing the center pillar garnish cover LH, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001XP8

      Detach the 2 clips and 2 guides, and remove the center pillar garnish cover LH.

  18. REMOVE CENTER PILLAR GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  19. REMOVE CENTER LOWER PILLAR GARNISH LH

    Tech Tips


    • for Manual Seat:

      When removing the center lower pillar garnish LH, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001Y3K

      Remove the bolt and seat belt anchor.

    2. B001Z8X

      Detach the 2 claws and 7 clips, and remove the center lower pillar garnish LH..

  20. REMOVE CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  21. REMOVE REAR ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both rear assist grip assemblies.


    1. B001WIF

      Detach the 4 claws and remove the 2 assist grip plugs.

    2. B001VUB

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip assembly.

  22. REMOVE CENTER PILLAR GARNISH LH

    B001WRF

    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish LH.

  23. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  24. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

    B001WHB

    Tech Tips

    Use the same procedure for both No. 1 tonneau cover holder caps.


    1. Detach the 2 claws and remove the No. 1 tonneau cover holder cap.

  25. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for both No. 1 luggage compartment trim hooks.


    1. B001WEWE01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  26. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B001XME

    Tech Tips

    When removing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B001Z6R

      Detach the 3 claws and remove the outer lap belt anchor cover.

    2. B001YLX

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001XHX

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 18 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly LH.

      4. w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly LH.

        B001WZM

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.

        B001XJ5

    6. w/ Tonneau Cover:


      1. Remove the screw and clip.

      2. Detach the 18 clips and 2 claws, and remove the front quarter trim panel assembly LH.

        B001ZG2

  27. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    B001X5H

    Tech Tips

    When removing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B001ZAG

      Detach the 3 claws and remove the outer lap belt anchor cover.

    2. B001YAN

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001W3C

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Detach the 3 claws and remove the outer lap belt anchor cover.

      2. B00201O

        Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 16 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the front quarter trim panel assembly RH.

      4. w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the front quarter trim panel assembly RH.

        B001XI2

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.

        B001WA2

    6. w/ Tonneau Cover:


      1. Remove the screw and clip.

      2. Detach the 16 clips and 2 claws, and remove the front quarter trim panel assembly RH.

        B001Z86

  28. REMOVE REAR FRONT QUARTER TRIM GARNISH LH

    B001X8C

    1. Remove the screw.

    2. Detach the clip and 2 guides.

    3. Pass the seat belt anchor through the rear front quarter trim garnish LH, and remove the rear front quarter trim garnish LH.

  29. REMOVE REAR FRONT QUARTER TRIM GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  30. REMOVE REAR UPPER PILLAR GARNISH LH


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. B001WCLE01
        Text in Illustration
        *a Protective Tape

        Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

        Tech Tips

        Tape the screwdriver tip before use.

      2. B001XKP

        Remove the bolt and seat belt shoulder anchor.

    2. B001YLH

      Detach the 5 clips and remove the rear upper pillar garnish LH.

  31. REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)

    Click here

  32. REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

    Click here

  33. REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

    Click here

  34. REMOVE REAR UPPER PILLAR GARNISH RH

    B001WCLE01

    1. Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *a Protective Tape
    2. B001WBK

      Remove the bolt and seat belt shoulder anchor.

    3. B001ZJF

      w/o Power Back Door:


      1. Detach the 5 clips and remove the rear upper pillar garnish RH.

    4. B001YYPE01
      Text in Illustration
      *a Power Back Door Rod

      w/ Power Back Door:


      1. Detach the 5 clips.

      2. Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish RH.

  35. REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)

    Click here

  36. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. for Bulb Type:

      Click here

    2. for LED Type:

      Click here

  37. REMOVE NO. 3 ROOM LIGHT ASSEMBLY

    Click here

  38. REMOVE VISOR BRACKET COVER

    Tech Tips

    Use the same procedure for both visor bracket covers.


    1. B001ZTF

      Detach the 4 claws and remove the visor bracket cover.

  39. REMOVE VISOR ASSEMBLY LH

    B002003

    1. Remove the 2 screws and visor assembly LH.

  40. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  41. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. B001XY3E02

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  42. REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

    B001Z41E01
    Text in Illustration
    *a Protective Tape
    *b Cover

    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor assembly LH.

      Tech Tips

      Tape the screwdriver tip before use.

  43. REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Tech Tips

    Use the same procedures described for the LH side.

  44. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  45. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  46. REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  47. REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  48. REMOVE SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

    B001ZD9

    1. Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.

  49. REMOVE ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip assemblies.


    1. B001YYGE01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. ach the 2 clips and remove the assist grip assembly.

    3. Remove the 2 clips from the vehicle body.

  50. REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

      Remove the No. 2 assist grip assembly.


      1. B001YPLE01
        Text in Illustration
        *a Protective Tape

        Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the No. 2 assist grip assembly LH.

      3. Remove the 2 clips from the vehicle body.

    2. w/ Rear No. 2 Seat, for Face to Face Seat Type:

      Remove the No. 2 assist grip assembly.


      1. B001YYGE01
        Text in Illustration
        *a Protective Tape

        Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the No. 2 assist grip assembly LH.

      3. Remove the 2 clips from the vehicle body.

  51. REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  52. REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for both 3rd seat assist grip assemblies.


    1. B001W9HE01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the 3rd seat assist grip assembly.

    3. Remove the 2 clips from the vehicle body.

  53. REMOVE ROOF HEADLINING ASSEMBLY

    B001VZ6

    Tech Tips


    • for Manual Seat:

      When removing the roof headlining assembly, move the front seat and rear No. 1 seat to the position shown in the illustration.

    • for Power Seat:

      When removing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • for Power Seat:

      After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. B001X31

      w/ EC Mirror:

      Disconnect the connector.

    2. B001XSE

      w/ Rain Sensor:

      Disconnect the connector.

    3. w/ Pre-crash Safety System:


      1. B001Y1G

        w/o Camera Heater:

        Disconnect the 2 connectors.

      2. B001VXR

        w/ Camera Heater:

        Disconnect the 3 connectors.

    4. B001WA0E01

      Disconnect the 3 roof wire connectors.


      1. w/ Rear Wiper:

        Disconnect the washer hose.

    5. Detach the 4 clamps.

      Text in Illustration
      *a Front Left Side
      *b Washer Hose
    6. B001WXAE01

      Remove the bolt.

    7. Disconnect the antenna cord connector and detach the 2 clamps.

      Text in Illustration
      *a Front Right Side
    8. B001VX1E01
      Text in Illustration
      *a Rear Right Side

      Disconnect the antenna cord connector.

    9. B001WTDE01
      Text in Illustration
      *a Rear Left Side

      w/ Rear Wiper:

      Disconnect the washer hose.

    10. for 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 2 clips and 2 guides.

      B001ZQLE01
      Text in Illustration
      *A for 3 Person Seat Type Rear No. 2 Seat - -

    11. except 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 3 clips and 2 guides.

      B001W99E01
      Text in Illustration
      *A except 3 Person Seat Type Rear No. 2 Seat - -
    12. B001YYH

      Remove the roof headlining assembly from the rear of the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining assembly when taking it out.

  54. REMOVE FRONT ROOF SIDE RAIL GARNISH LH

    B001XB7E01
    Text in Illustration
    *a Cut Off Position

    1. Detach the 3 clips.

    2. Cut off the 3 clips and remove the front roof side rail garnish LH.

    3. Remove 3 clips from the vehicle body.

  55. REMOVE FRONT ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  56. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B001ZAH

    1. Remove the front door opening trim weatherstrip LH.

  57. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  58. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B001WE3

    1. Remove the rear door opening trim weatherstrip LH.

  59. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  60. REMOVE BACK DOOR WEATHERSTRIP

    B001VQ9

    1. Remove the back door weatherstrip.

  61. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    B001W1PE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the front door scuff plate outside LH.

    2. Detach the 4 clips and remove the front door scuff plate outside LH.

  62. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  63. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    B001W1TE01
    Text in Illustration
    *a Protective Tape

    1. Put protective tape around the rear door scuff plate outside LH.

    2. Detach the 3 clips and remove the rear door scuff plate outside LH.

  64. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  65. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001YT2

    1. Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.

  66. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  67. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001ZQX

    1. Detach the 6 claws and remove the rear shoulder belt anchor plate sub-assembly LH.

  68. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  69. REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YIH

    1. Detach the 7 claws and remove the roof side inner garnish cover LH.

  70. REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  71. REMOVE REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for both rear No. 1 seat shoulder belt hangers.


    1. B001YD6E01
      Text in Illustration
      *a Spring Nut

      Remove the 2 spring nuts and rear No. 1 seat shoulder belt hanger.

  72. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH

    B001WQYE01
    Text in Illustration
    *a Spring Nut

    1. Remove the 2 spring nuts and rear No. 2 seat shoulder belt hanger.

  73. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedures described for the LH side.

  74. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH

    B002038

    1. w/ Rear Heater:

      Remove the 8 screws and duct.

    2. B001X84

      Remove the 7 screws.

    3. Detach the 4 claws and remove the quarter trim cover sub-assembly LH.

  75. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH

    B001ZLG

    1. Remove the 7 screws.

    2. Detach the 4 claws and remove the quarter trim cover sub-assembly RH.

  76. REMOVE NO. 2 CUP HOLDER

    B001XWJ

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the No. 2 cup holder.

  77. REMOVE NO. 1 CUP HOLDER

    B001XCS

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the No. 1 cup holder.

  78. REMOVE TONNEAU COVER HOLDER BRACKET LH (w/ Tonneau Cover)

    B001XIQE01
    Text in Illustration
    *a Front Quarter trim base

    1. Remove the 8 screws.

    2. Detach the 3 claws and remove the tonneau cover holder bracket LH and front quarter trim base.

  79. REMOVE TONNEAU COVER HOLDER BRACKET RH (w/ Tonneau Cover)

    Tech Tips

    Use the same procedures described for the LH side.

  80. REMOVE TONNEAU COVER HANGER LH (w/ Tonneau Cover)

    B001W56E01
    Text in Illustration
    *a Rear Quarter trim base

    1. Remove the 2 screws, tonneau cover hanger LH and rear quarter trim base.

  81. REMOVE TONNEAU COVER HANGER RH (w/ Tonneau Cover)

    Tech Tips

    Use the same procedures described for the LH side.

  82. REMOVE NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001YPJ

    1. Detach the 4 claws and remove the No. 1 side trim base cover LH.

  83. REMOVE NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    B001VTB

    1. Remove the 6 screws and duct.

    2. B001XGH

      Detach the 4 claws and remove the No. 1 side trim base cover RH.

  84. REMOVE NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001Z9U

    1. Detach the 4 claws and remove the No. 2 side trim base cover LH.

  85. REMOVE NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    Tech Tips

    Use the same procedures described for the LH side.

  86. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

  87. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  88. REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YAE

    1. Detach the 6 clips and remove the rear No. 2 seat cover bezel.

  89. REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the rear No. 2 seat cover bezel.

  90. REMOVE QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    B001VOU

    1. Detach the 6 clips and remove the quarter trim cover LH.

  91. REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  92. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Remove the quarter trim lid sub-assembly RH.

  93. REMOVE SIDE TRIM BOX COVER


    1. Remove the side trim box cover.

  94. REMOVE SIDE TRIM BOX

    B001Z04

    1. Remove the 9 screws and side trim box.