ROOF HEADLINING(w/ Sliding Roof) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL SIDE TRIM BOX

    B001Z04

    1. Install the side trim box with the 9 screws.

  2. INSTALL SIDE TRIM BOX COVER


    1. Install the side trim box cover.

  3. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Install the quarter trim lid sub-assembly RH.

  4. INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

    B001VOU

    1. Attach the 6 clips to install the quarter trim cover LH.

  5. INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  6. INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YAE

    1. Attach the 6 clips to install the rear No. 2 seat cover bezel.

  7. INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the rear No. 2 seat cover bezel.

  8. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

  9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  10. INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001Z9U

    1. Attach the 4 claws to install the No. 2 side trim base cover LH.

  11. INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    Tech Tips

    Use the same procedures described for the LH side.

  12. INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001YPJ

    1. Attach the 4 claws to install the No. 1 side trim base cover LH.

  13. INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    B001XGH

    1. Attach the 4 claws to install the No. 1 side trim base cover RH.

    2. B001VTB

      Install the duct with the 6 screws.

  14. INSTALL NO. 2 CUP HOLDER

    B001ZNB

    1. Attach the 3 claws to install the No. 2 cup holder.

    2. Install the 5 screws.

  15. INSTALL NO. 1 CUP HOLDER

    B001WBA

    1. Attach the 3 claws to install the No. 1 cup holder.

    2. Install the 5 screws.

  16. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH

    B001ZDA

    1. Attach the 4 claws to install the quarter trim cover sub-assembly LH.

    2. Install the 7 screws.

    3. B002038

      w/ Rear Heater:

      Install the duct with the 8 screws.

  17. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH

    B001Y7R

    1. Attach the 4 claws to install the quarter trim cover sub-assembly RH.

    2. Install the 7 screws.

  18. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH

    B001WQYE01
    Text in Illustration
    *a Spring Nut

    1. Install the rear No. 2 seat shoulder belt hanger LH with new 2 spring nuts.

  19. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedures described for the LH side.

  20. INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for both rear No. 1 seat shoulder belt hangers.


    1. B001YD6E01
      Text in Illustration
      *a Spring Nut

      Install the rear No. 1 seat shoulder belt hanger with new 2 spring nuts.

  21. INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YIH

    1. Attach the 7 claws to install the roof side inner garnish cover LH.

  22. INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  23. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001ZQX

    1. Attach the 6 claws to install the rear shoulder belt anchor plate sub-assembly LH.

  24. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  25. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001VUZ

    1. Slide the front shoulder belt anchor plate sub-assembly LH in the direction shown in the illustration and attach the 6 claws to install the front shoulder belt anchor plate sub-assembly LH.

  26. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  27. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

    B001X9U

    1. Attach the 3 clips to install the rear door scuff plate outside LH.

  28. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  29. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

    B001WTM

    1. Attach the 4 clips to install the front door scuff plate outside LH.

  30. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  31. INSTALL BACK DOOR WEATHERSTRIP

    B001Z8EE04
    Text in Illustration
    *a Alignment Mark
    *b Mark

    1. Install the back door weatherstrip as shown in the illustration.

  32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B001YY1E05
    Text in Illustration
    *a Alignment Mark
    *b Mark

    1. Install the rear door opening trim weatherstrip LH as shown in the illustration.

  33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  34. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B001WM5E04
    Text in Illustration
    *a Alignment Mark
    *b Mark

    1. Install the front door opening trim weatherstrip LH as shown in the illustration.

  35. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  36. INSTALL ROOF HEADLINING ASSEMBLY

    B001VZ6

    Tech Tips


    • for Manual Seat:

      When installing the roof headlining assembly, move the front seat and rear No. 1 seat to the position shown in the illustration.

    • for Power Seat:

      When installing the roof headlining assembly, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • for Power Seat:

      After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. B001ZYH

      Place the roof headlining assembly in the cabin from the rear of the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining assembly when placing it in the cabin.

    2. for 3 Person Seat Type Rear No. 2 Seat:

      Attach the 12 claws, 2 clips, 2 guides and 16 fasteners to install the headlining.

      B001VSJE03
      Text in Illustration
      *A for 3 Person Seat Type Rear No. 2 Seat - -
      *a Guide - -

    3. except 3 Person Seat Type Rear No. 2 Seat:

      Attach the 12 claws, 3 clips, 2 guides and 16 fasteners to install the headlining.

      B001VX5E04
      Text in Illustration
      *A except 3 Person Seat Type Rear No. 2 Seat - -
      *a Guide - -
    4. B001WTDE02
      Text in Illustration
      *a Rear Left Side

      Connect the washer hose.

    5. B001VX1E01
      Text in Illustration
      *a Rear Right Side

      Connect the antenna cord connector.

    6. B001WXAE02

      Connect the antenna cord connector and attach the 2 clamps.

    7. Install the bolt.

      Text in Illustration
      *a Front Right Side
    8. B001WA0E02

      Connect the 3 roof wire connectors and washer hose.

    9. Attach the 4 clamps.

      Text in Illustration
      *a Front Left Side
      *b Washer Hose
    10. B001X50

      Connect the connector.

    11. w/ Pre-crash Safety System:


      1. B001Y1G

        w/o Camera Heater:

        Connect the 2 connectors.

      2. B001VXR

        w/ Camera Heater:

        Connect the 3 connectors.

    12. B001XSE

      w/ Rain Sensor:

      Connect the connector.

    13. B001X31

      w/ EC Mirror:

      Connect the connector.

  37. INSTALL FRONT ROOF SIDE RAIL GARNISH LH

    B001WGAE02
    Text in Illustration
    *a New Clip

    1. Install 3 new clips to the front roof side rail garnish LH.

    2. Attach the 3 clips to install the front roof side rail garnish LH.

  38. INSTALL FRONT ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  39. INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for both 3rd seat assist grip assemblies.


    1. B001W2K

      Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the 3rd seat assist grip assembly.

  40. INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

      Install the No. 2 assist grip assembly.


      1. B001ZEW

        Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

      2. Install the No. 2 assist grip assembly LH.

    2. w/ Rear No. 2 Seat, for Face to Face Seat Type:

      Install the No. 2 assist grip assembly.


      1. B001W2K

        Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

      2. Install the No. 2 assist grip assembly LH.

  41. INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  42. INSTALL ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip assemblies.


    1. B001W2K

      Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip assembly.

  43. INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

    B001ZD9

    1. Attach the 4 guides and 4 clips to install the seat belt anchor cover.

  44. INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  45. INSTALL NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  46. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  47. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  48. INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

    B001VS8

    1. Attach the 2 clips to install the center visor assembly LH.

  49. INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Tech Tips

    Use the same procedures described for the LH side.

  50. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for visor holders.


    1. B001XFW

      Attach the 2 claws.

    2. Push the visor holder in to install it.

  51. INSTALL VISOR ASSEMBLY LH

    B002003

    1. Install the visor assembly LH with the 2 screws.

  52. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  53. INSTALL VISOR BRACKET COVER

    Tech Tips

    Use the same procedure for visor bracket covers.


    1. B001ZTF

      Attach the 4 claws to install the visor bracket cover.

  54. INSTALL NO. 3 ROOM LIGHT ASSEMBLY

    Click here

  55. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


    1. for Bulb Type:

      Click here

    2. for LED Type:

      Click here

  56. INSTALL MAP LIGHT ASSEMBLY

    Click here

  57. INSTALL REAR UPPER PILLAR GARNISH LH

    B001YLH

    1. Attach the 5 clips to install the rear upper pillar garnish LH.

    2. B001XKP

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Install the seat belt shoulder anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      2. B001Y54

        Attach the 2 claws to close the seat belt shoulder anchor cover.

  58. INSTALL REAR UPPER PILLAR GARNISH RH

    B001ZJF

    1. w/o Power Back Door:


      1. Attach the 5 clips to install the rear upper pillar garnish RH.

    2. B001YODE01
      Text in Illustration
      *a Power Back Door Rod

      w/ Power Back Door:


      1. Pass the power back door rod through the rear upper pillar garnish RH.

      2. Attach the 5 clips to install the rear upper pillar garnish RH.

    3. B001WBK

      Install the seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. B001Y91

      Attach the 2 claws to close the seat belt shoulder anchor cover.

  59. INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

    Click here

  60. INSTALL BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

    Click here

  61. INSTALL BACK DOOR GARNISH CENTER (w/ Power Back Door)

    Click here

  62. INSTALL REAR FRONT QUARTER TRIM GARNISH LH

    B001X8C

    1. Pass the seat belt anchor through the rear front quarter trim garnish LH.

    2. Attach the clip and 2 guides to install the rear front quarter trim garnish LH.

    3. Install the screw.

  63. INSTALL REAR FRONT QUARTER TRIM GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  64. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B001XME

    Tech Tips

    When installing the front quarter trim panel assembly LH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. w/o Rear Air Conditioning System:

        Connect the rear seat lock control lever cable.

      2. w/ Rear Air Conditioning System:

        Connect the thermistor connector and rear seat lock control lever cable.

      3. Attach the 18 clips and 2 claws to install the front quarter trim panel assembly LH.

      4. Install the clip and bolt.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }
        B001WZM

    2. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Attach the 18 clips and 2 claws to install the front quarter trim panel assembly LH.

      2. Install the clip.

        B001XJ5
    3. B001W09E04
      Text in Illustration
      *a Protruding Part

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

    4. B001YLX

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. B001Z6R

      Attach the 3 claws to install the outer lap belt anchor cover.

  65. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    B001X5H

    Tech Tips

    When installing the front quarter trim panel assembly RH, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. w/o Rear Air Conditioning System:

        Connect the rear seat lock control lever cable.

      2. w/ Rear Air Conditioning System:

        Connect the thermistor connector and rear seat lock control lever cable.

      3. Attach the 16 clips and 2 claws to install the front quarter trim panel assembly RH.

      4. Install the clip and bolt.

        Torque:
        12 N*m  { 122 kgf*cm, 9 ft.*lbf }
        B001XI2

    2. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Attach the 16 clips and 2 claws to install the front quarter trim panel assembly RH.

      2. Install the clip.

        B001WA2
    3. B00201O

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Install the rear No. 2 seat belt anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      2. B001W3C

        Attach the 3 claws to install the outer lap belt anchor cover.

    4. B001YAN

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. B001ZAG

      Attach the 3 claws to install the outer lap belt anchor cover.

  66. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedure for rear seat cover caps.


    1. B001XR0

      Attach the 3 claws to install the rear seat cover cap.

  67. INSTALL CENTER PILLAR GARNISH LH

    B001WRF

    1. Pass the seat belt anchor through the center pillar garnish LH.

    2. Attach the 2 clips and 2 guides to install the center pillar garnish LH.

    3. Install the bolt.

  68. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  69. INSTALL REAR ASSIST GRIP ASSEMBLY

    Tech Tips

    Use the same procedure for both rear assist grip assemblies.


    1. B001VUB

      Attach the 2 claws to install the rear assist grip assembly.

    2. Install the 2 bolts.

    3. B001WIF

      Attach the 4 claws to install the 2 assist grip plugs.

  70. INSTALL CENTER LOWER PILLAR GARNISH LH

    Tech Tips


    • for Manual Seat:

      When installing the center lower pillar garnish LH, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When installing the center lower pillar garnish LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001Z8X

      Attach the 2 claws and 7 clips to install the center lower pillar garnish LH.

    2. B001Y3K

      Install the seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  71. INSTALL CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  72. INSTALL CENTER PILLAR GARNISH COVER LH

    Tech Tips


    • for Manual Seat:

      When installing the center pillar garnish cover LH, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When installing the center pillar garnish cover LH, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001XP8

      Attach the 2 clips and 2 guides to install the center pillar garnish cover LH.

  73. INSTALL CENTER PILLAR GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  74. INSTALL FRONT PILLAR GARNISH LH

    B001Z6Z

    1. w/ Speaker:

      Connect the speaker connector.

    2. Attach the clip and 3 guides to install the front pillar garnish LH.

  75. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  76. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for both assist grip sub-assemblies.


    1. B001XJZ

      Attach the 2 claws to install the assist grip sub-assembly.

    2. Install the 2 bolts.

    3. B001Y9H

      Attach the 4 claws to install the 2 assist grip plugs.

  77. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    B001WTN

    1. Attach the 6 clips to install the rear floor mat support plate.

  78. INSTALL REAR DOOR SCUFF PLATE LH

    B001Z1V

    1. Attach the 3 claws and 4 clips to install the rear door scuff plate LH.

    2. Install the screw.

  79. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  80. INSTALL REAR STEP COVER

    Tech Tips

    Use the same procedure for both rear step covers.


    1. B001ZUZ

      Attach the 2 claws to install the rear step cover.

  81. INSTALL FRONT DOOR SCUFF PLATE LH

    B001ZKS

    1. Attach the 7 claws and 4 clips to install the front door scuff plate LH.

  82. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  83. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)

    Click here

  84. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  85. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)

    Click here

  86. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  87. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  88. CHECK SRS WARNING LIGHT

    Click here