INSTRUMENT PANEL SAFETY PAD INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)


    1. Install the instrument panel safety pad with the 8 bolts and 2 nuts.

    2. Install the 2 passenger airbag bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      A01X49Y

    3. Connect the wire harness with the bolt.

    4. Connect the connectors and attach the clamps.

      A01XAHD

    5. Connect the connectors.

      A01WZRIE01
      *1 w/ Parking Assist Monitor System:
      *2 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:

  2. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)


    1. Install the instrument panel safety pad with the 8 bolts and 2 nuts.

    2. Connect the connectors.

    3. Install the 2 passenger airbag bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      A01X92A

    4. Connect the wire harness with the bolt.

    5. Connect the connectors and attach the clamps.

      A01WZ53

    6. Connect the connectors.

      A01X6ZBE01
      *1 w/ Parking Assist Monitor System:
      *2 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:

  3. INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

    B001ZFM

    1. Attach the clip to install the rear No. 4 air duct.

  4. INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

    B001WYX

    1. Attach the clip to install the rear No. 2 air duct.

  5. INSTALL AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  6. INSTALL MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (w/ Multi-display)

    Click here

  7. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

    B001WMW

    1. Install the radio tuner opening cover with the 2 bolts and 2 screws.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  8. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Cassette Tape Player)

    Click here

  9. INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL

    B001W0V

    1. Connect the connector.

    2. Attach the 10 claws to install the No. 1 center instrument cluster finish panel.

  10. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Multi-display)

    Click here

  11. INSTALL MULTI-DISPLAY ASSEMBLY WITH BRACKET (w/ Multi-display)

    Click here

  12. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01XBGV

    1. Connect the connector.

    2. Attach the 6 claws to install the No. 4 instrument panel register.

  13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01X2WQ

    1. Connect the connector.

    2. Attach the 6 claws to install the No. 3 instrument panel register.

  14. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (RH Side)

    Click here

  15. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  16. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (LH Side)

    Click here

  17. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  18. INSTALL FRONT NO. 4 SPEAKER ASSEMBLY

    Click here

  19. INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY

    Click here

  20. INSTALL FRONT PILLAR GARNISH RH (w/ Sliding Roof)

    Click here

  21. INSTALL FRONT PILLAR GARNISH RH (w/o Sliding Roof)

    Click here

  22. INSTALL FRONT PILLAR GARNISH LH (w/ Sliding Roof)

    Click here

  23. INSTALL FRONT PILLAR GARNISH LH (w/o Sliding Roof)

    Click here

  24. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Sliding Roof)

    Click here

  25. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

    Click here

  26. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01X1U8

    1. Attach the 4 claws to install the No. 2 instrument panel register.

  27. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    A01X3XG

    1. Connect the connector.

    2. Attach the 3 claws to install the lower No. 2 instrument panel finish panel.

    3. Install the 4 bolts.

  28. INSTALL INSTRUMENT PANEL BOX DOOR KNOB

    B001X38

    1. Attach the 2 claws to install the instrument panel box door knob.

  29. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01X2MQ

    1. Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.

  30. INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

    A01X6H1

    1. Attach the 4 claws to install the lower instrument panel.

    2. Install the 2 bolts.

  31. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

    Click here

  32. INSTALL COWL SIDE TRIM BOARD RH

    A01X9H9

    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  33. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A01X730

    1. Attach the 4 claws to install the No. 2 instrument panel under cover.

  34. INSTALL FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof)

    Click here

  35. INSTALL FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof)

    Click here

  36. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

    A01XB42

    1. Connect the connector.

    2. Attach the 6 claws to install the instrument side panel.

  37. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

    A01XB3P

    1. Attach the 6 claws to install the instrument side panel.

  38. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01WYYJ

    1. Attach the 4 claws to install the No. 1 instrument panel register.

  39. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    A01X34S

    1. Attach the 2 claws and connect the DLC3.

    2. Install the lower instrument panel with the 5 bolts.

  40. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  41. INSTALL NO. 1 SWITCH HOLE BASE

    A01X2FO

    1. Connect the connectors.

    2. Attach the 4 claws to install the No. 1 switch hole base.

  42. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. B001WCJ

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. B001XC5

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A01X1FZ

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A01X77I
    6. B001ZC6

      Attach the 2 claws to close the hole cover.

  43. INSTALL COWL SIDE TRIM BOARD LH

    A01X0KR

    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  44. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A01X0M5

    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  45. INSTALL FRONT DOOR SCUFF PLATE LH (w/ Sliding Roof)

    Click here

  46. INSTALL FRONT DOOR SCUFF PLATE LH (w/o Sliding Roof)

    Click here

  47. INSTALL COMBINATION METER ASSEMBLY (w/o Multi-information Display)

    A01X3HX

    1. Connect the connectors.

    2. Install the combination meter with the 4 screws.

  48. INSTALL COMBINATION METER ASSEMBLY (w/ Multi-information Display)

    A01X6NE

    1. Connect the connectors.

    2. Install the combination meter with the 4 screws.

  49. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

    A01XAYH

    1. Attach the 9 claws to install the instrument cluster finish panel.

  50. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

    A01XBNE

    1. Connect the connector.

    2. Attach the 9 claws to install the instrument cluster finish panel.

  51. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

      A01X9WPE01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System

  52. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01WZYJ

    1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

  53. INSTALL INSTRUMENT SIDE PANEL LH

    A01X2PL

    1. Attach the 6 claws to install the instrument side panel.

  54. INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)

    Click here

  55. INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)

    Click here

  56. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

    Click here

  57. INSTALL FRONT SEAT ASSEMBLY RH (for Bench Seat Type)

    Click here

  58. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

    Click here

  59. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

    Click here

  60. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  61. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  62. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  63. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

    Click here

  64. INSTALL TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

    Click here

  65. INSTALL UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  66. INSTALL UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  67. INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  68. INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  69. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  70. INSTALL STEERING PAD

    Click here

  71. INSTALL LOWER NO. 2 STEERING WHEEL COVER

    Click here

  72. INSTALL LOWER NO. 3 STEERING WHEEL COVER

    Click here

  73. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • for Power Tilt and Power Telescopic Steering Column:

      Reset the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  74. CHARGE REFRIGERANT (w/ Cool Box)

    Click here

  75. WARM UP ENGINE (w/ Cool Box)

    Click here

  76. CHECK FOR REFRIGERANT GAS LEAK (w/ Cool Box)

    Click here

  77. CHECK SRS WARNING LIGHT

    Click here