INSTRUMENT PANEL SAFETY PAD REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. TABLE OF BOLT, SCREW AND NUT

    Tech Tips

    All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.

    A01X829E01

  2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Cool Box)

    Click here

  3. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. for Power Tilt and Power Telescopic Steering Column:


      1. Disable the Autoaway/Return function by changing the customize parameter Click here.

        Note

        Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

        Tech Tips

        Performing the above operation causes the Autoaway/Return function to be disabled when the engine switch is turned off.

      2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.

    2. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE LOWER NO. 3 STEERING WHEEL COVER

    Click here

  6. REMOVE LOWER NO. 2 STEERING WHEEL COVER

    Click here

  7. REMOVE STEERING PAD

    Click here

  8. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  9. REMOVE LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  10. REMOVE LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  11. REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

    Click here

  12. REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  13. REMOVE TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic Steering Column)

    Click here

  14. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

    Click here

  15. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

    Click here

  16. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  17. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  18. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

    Click here

  19. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

    Click here

  20. REMOVE FRONT SEAT ASSEMBLY RH (for Bench Seat Type)

    Click here

  21. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

    Click here

  22. REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)

    Click here

  23. REMOVE LOWER CONSOLE BOX (w/o Console Box Lid)

    Click here

  24. REMOVE INSTRUMENT SIDE PANEL LH

    A01X2EME06
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  25. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01X2ZME04
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.

  26. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

      A01WZ9FE02
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
      *1 Protective Tape - -

  27. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

    A01XBNE

    1. Detach the 9 claws.

    2. Disconnect the connector and remove the instrument cluster finish panel.

  28. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

    A01XAYH

    1. Detach the 9 claws and remove the instrument cluster finish panel.

  29. REMOVE COMBINATION METER ASSEMBLY (w/ Multi-information Display)

    A01X6NE

    1. Remove the 4 screws.

    2. Disconnect the connectors and remove the combination meter.

  30. REMOVE COMBINATION METER ASSEMBLY (w/o Multi-information Display)

    A01X3HX

    1. Remove the 4 screws.

    2. Disconnect the connectors and remove the combination meter.

  31. REMOVE FRONT DOOR SCUFF PLATE LH (w/o Sliding Roof)

    Click here

  32. REMOVE FRONT DOOR SCUFF PLATE LH (w/ Sliding Roof)

    Click here

  33. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A01X3VN

    1. Remove the 2 screws.

    2. Detach the 3 claws.

    3. Disconnect the connectors and remove the No. 1 instrument panel under cover.

  34. REMOVE COWL SIDE TRIM BOARD LH

    A01X0KR

    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  35. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01X715E01

    1. Using a screwdriver, detach the 2 claws and open the hole cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape

    2. w/ Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. Detach the 16 claws.

        A01X1FZ

    3. w/o Driver Side Knee Airbag:


      1. Remove the 2 bolts.

      2. Detach the 9 claws.

        A01X77I
    4. B001WCJ

      for Automatic Air Conditioning System:


      1. Detach the 2 claws and remove the room temperature sensor.

    5. B001XC5

      Detach the 2 claws and disconnect the 2 control cables.

    6. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.

  36. REMOVE NO. 1 SWITCH HOLE BASE

    A01X2FO

    1. Detach the 4 claws.

    2. Disconnect the connectors and remove the No. 1 switch hole cover.

  37. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  38. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    A01X34S

    1. Detach the 2 claws and disconnect the DLC3.

    2. Remove the 5 bolts and lower instrument panel.

  39. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01WYYJ

    1. Detach the 4 claws and remove the No. 1 instrument panel register.

  40. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

    A01X07GE02
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  41. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

    A01XATXE02
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the instrument side panel.

  42. REMOVE FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof)

    Click here

  43. REMOVE FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof)

    Click here

  44. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A01X96O

    1. Detach the 4 claws and remove the No. 2 instrument panel under cover.

  45. REMOVE COWL SIDE TRIM BOARD RH

    A01X9H9

    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  46. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

    Click here

  47. REMOVE LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

    A01X6H1

    1. Remove the 2 bolts.

    2. Detach the 4 claws and remove the lower instrument panel.

  48. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01X4LXE02
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws and remove the No. 3 instrument cluster finish panel garnish.

  49. REMOVE INSTRUMENT PANEL BOX DOOR KNOB

    B001ZZZ

    1. Using a moulding remover, detach the 2 claws and remove the instrument panel box door knob.

  50. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    A01X3XG

    1. Remove the 4 bolts.

    2. Detach the 3 claws.

    3. Disconnect the connector and remove the lower No. 2 instrument panel finish panel.

  51. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01X1U8

    1. Detach the 4 claws and remove the No. 2 instrument panel register.

  52. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

    Click here

  53. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Sliding Roof)

    Click here

  54. REMOVE FRONT PILLAR GARNISH LH (w/o Sliding Roof)

    Click here

  55. REMOVE FRONT PILLAR GARNISH LH (w/ Sliding Roof)

    Click here

  56. REMOVE FRONT PILLAR GARNISH RH (w/o Sliding Roof)

    Click here

  57. REMOVE FRONT PILLAR GARNISH RH (w/ Sliding Roof)

    Click here

  58. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

    Click here

  59. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY

    Click here

  60. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  61. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (LH Side)

    Click here

  62. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

    Click here

  63. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (RH Side)

    Click here

  64. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01X406E03
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the No. 3 instrument panel register.

  65. REMOVE NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY

    A01X0VVE03
    Text in Illustration
    *1 Protective Tape

    1. Place protective tape as shown in the illustration.

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the No. 4 instrument panel register.

  66. REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET (w/ Multi-display)

    Click here

  67. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Multi-display)

    Click here

  68. REMOVE NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL

    B001W0V

    1. Detach the 10 claws.

    2. Disconnect the connector and remove the No. 1 center instrument cluster finish panel.

  69. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Cassette Tape Player)

    Click here

  70. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

    B001WMW

    1. Remove the 2 bolts.

    2. Remove the 2 screws and radio tuner opening cover with bracket.

  71. REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY WITH BRACKET (w/ Multi-display)

    Click here

  72. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  73. REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

    B001WYX

    1. Fold back the front floor carpet.

    2. Detach the clip and remove the rear No. 2 air duct.

  74. REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

    B001ZFM

    1. Fold back the front floor carpet.

    2. Detach the clip and remove the rear No. 4 air duct.

  75. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)


    1. Disconnect the connectors.

      A01WZRIE01
      *1 w/ Parking Assist Monitor System:
      *2 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:

    2. Disconnect the connectors and detach the clamps.

    3. Remove the bolt and disconnect the wire harness.

      A01XAHD

    4. Remove the 2 passenger airbag bolts.

    5. Disconnect the connectors.

    6. Remove the 8 bolts.

    7. Remove the 2 nuts and instrument panel safety pad.

      A01X49Y

  76. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)


    1. Disconnect the connectors.

      A01X6ZBE01
      *1 w/ Parking Assist Monitor System:
      *2 w/ TOYOTA Parking Assist-Sensor System and w/o Parking Assist Monitor System:

    2. Disconnect the connectors and detach the clamps.

    3. Remove the bolt and disconnect the wire harness.

      A01WZ53

    4. Remove the 2 passenger airbag bolts.

    5. Disconnect the connectors.

    6. Remove the 8 bolts.

    7. Remove the 2 nuts and instrument panel safety pad.

      A01X92A