ROOF HEADLINING(w/ Sliding Roof) REMOVAL

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH Click here.

  4. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)


    1. Remove the rear No. 2 seat assembly LH Click here.

  6. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  7. REMOVE FRONT DOOR SCUFF PLATE LH

    B001ZKS

    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  8. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  9. REMOVE REAR STEP COVER

    B001ZUZ

    Tech Tips

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  10. REMOVE REAR DOOR SCUFF PLATE LH

    B001Z1V

    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  11. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    B001WTN

    1. Detach the 6 clips and remove the support plate.

  13. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

    B001Y9H

    Tech Tips

    Use the same procedure to remove the front assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. B001XJZ

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the front assist grip.

  14. REMOVE FRONT PILLAR GARNISH LH

    B001Z6Z

    1. Detach the clip 3 guides, and remove the front pillar garnish.

    2. for 9, 14 Speakers:

      Disconnect the speaker connector and then remove the front pillar garnish.

    3. B001WYKE03
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag.


      1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  15. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  16. REMOVE CENTER PILLAR GARNISH COVER LH

    Tech Tips


    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001XP8

      Detach the 2 clips and 2 guides, and remove the cover.

  17. REMOVE CENTER PILLAR GARNISH COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  18. REMOVE CENTER LOWER PILLAR GARNISH LH

    Tech Tips


    • for Manual Seat:

      When removing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. B001Y3K

      Remove the bolt and seat belt anchor.

    2. B001Z8X

      Detach the 2 claws and 7 clips, and remove the center lower pillar garnish.

  19. REMOVE CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  20. REMOVE REAR ASSIST GRIP ASSEMBLY

    B001WIF

    Tech Tips

    Use the same procedure to remove the rear assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. B001VUB

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip.

  21. REMOVE CENTER PILLAR GARNISH LH

    B001WRF

    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish.

  22. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  23. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001Y5PE03
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the rear seat cover cap on the other side.


    1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  24. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    B001XME

    Tech Tips

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B001Z6R

      Detach the 3 claws and remove the cover.

    2. B001YLX

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001XHX

      w/ Rear No. 2 Seat, except Face to Face Seat Type:

      Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 18 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

        B001WZM

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. Detach the 18 clips and 2 claws, and remove the quarter trim panel.

        B001XJ5

  25. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    B001X5H

    Tech Tips

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. B001ZAG

      Detach the 3 claws and remove the cover.

    2. B001YAN

      Remove the bolt and rear No. 1 seat belt anchor.

    3. B001W3C

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Detach the 3 claws and remove the cover.

      2. B00201O

        Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 16 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

        B001XI2

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. Detach the 16 clips and 2 claws, and remove the quarter trim panel.

        B001WA2

  26. REMOVE REAR FRONT QUARTER TRIM GARNISH LH

    B001X8C

    1. Remove the screw.

    2. Detach the clip and 2 guides.

    3. Pass the seat belt anchor through the quarter trim garnish, and remove the quarter trim garnish.

  27. REMOVE REAR FRONT QUARTER TRIM GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  28. REMOVE REAR UPPER PILLAR GARNISH LH


    1. B001Y81E01
      *1 Protective Tape

      w/ Rear No. 2 Seat, except Face to Face Seat Type


      1. Using a screwdriver, detach the 2 claws and open the seat belt shoulder anchor cover.

        Tech Tips

        Tape the screwdriver tip before use.

      2. B001XKP

        Remove the bolt and seat belt shoulder anchor.

    2. B001YLH

      Detach the 5 clips and remove the rear upper pillar garnish.

  29. REMOVE CENTER BACK DOOR GARNISH (w/ Power Back Door)

    Click here

  30. REMOVE BACK DOOR SIDE GARNISH RH (w/ Power Back Door)

    Click here

  31. REMOVE BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)

    Click here

  32. REMOVE REAR UPPER PILLAR GARNISH RH

    A01X1EP

    1. Using a moulding remover, detach the 2 claws and open the seat belt shoulder anchor cover.

    2. B001WBK

      Remove the bolt and seat belt shoulder anchor.

    3. B001ZJF

      w/o Power Back Door:


      1. Detach the 5 clips and remove the rear upper pillar garnish.

    4. B001YOBE04
      *1 Power Back Door Rod

      w/ Power Back Door:


      1. Detach the 5 clips.

      2. Pass the power back door rod through the rear upper pillar garnish, and remove the rear upper pillar garnish.

  33. REMOVE MAP LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 2 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Detach the 2 clips and 2 guides.

    4. Disconnect the connector and then remove the map light.

      B001XWNE03
      *1 Protective Tape

  34. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

    A01WZOA

    1. Detach the 4 clips.

    2. Disconnect the connector and then remove the room light.

  35. REMOVE NO. 2 ROOM LIGHT ASSEMBLY

    B001VUAE02
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the room light lens.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01X6BS

      Remove the 2 covers.

    3. B001VR8E02

      Using a screwdriver, push the 2 levers in the direction of the arrows in the illustration, and detach the 2 claws labeled A.

    4. Detach the 2 claws labeled B.

    5. B001WL1E02
      *1 Room Light Switch Base

      Detach the 4 claws and remove the room light from the room light switch base.

  36. REMOVE VISOR BRACKET COVER

    B001ZTF

    Tech Tips

    Use the same procedure to remove the visor bracket cover on the other side.


    1. Detach the 4 claws and remove the visor bracket cover.

  37. REMOVE VISOR ASSEMBLY LH

    B002003

    1. Remove the 2 screws and visor.

  38. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  39. REMOVE VISOR HOLDER

    B001XY3E02

    Tech Tips

    Use the same procedure to remove the visor holder on the other side.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  40. REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

    B001ZJBE03
    *1 Cover
    *2 Protective Tape

    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor.

      Tech Tips

      Tape the screwdriver tip before use.

  41. REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

    Tech Tips

    Use the same procedures described for the LH side.

  42. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

    Click here

  43. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  44. REMOVE SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

    B001ZD9

    1. Detach the 4 clips and 4 guides, and remove the seat belt anchor cover.

  45. REMOVE ASSIST GRIP ASSEMBLY

    B001WMYE07
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the assist grip on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  46. REMOVE NO. 2 ASSIST GRIP ASSEMBLY LH

    B001WOCE05
    *1 Protective Tape

    1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:

      Remove the No. 2 assist grip assembly.


      1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the assist grip.

      3. Remove the 2 clips from the vehicle body.

    2. B001WMYE08
      *1 Protective Tape

      w/ Rear No. 2 Seat, for Face to Face Seat Type:

      Remove the No. 2 assist grip assembly.


      1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Detach the 2 clips and remove the assist grip.

      3. Remove the 2 clips from the vehicle body.

  47. REMOVE NO. 2 ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  48. REMOVE 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001WMYE09
    *1 Protective Tape

    Tech Tips

    Use the same procedure to remove the 3rd seat assist grip on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  49. REMOVE ROOF HEADLINING ASSEMBLY

    B001VZ6

    Tech Tips


    • for Manual Seat:

      When removing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.

    • for Power Seat:

      When removing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.

    • for Power Seat:

      After moving the seats, disconnect the cable from the negative (-) battery terminal.


    1. A01X2WE

      w/ EC Mirror:

      Disconnect the inner mirror connector.

    2. A01XAR5

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. B001X50

      Disconnect the drive gear connector.

    4. B001YUQE01
      *1 Front Left Side
      *2 Washer Hose

      Disconnect the 3 roof wire connectors and washer hose.

    5. Detach the 4 clamps.

    6. B001YJCE01
      *1 Front Right Side

      Remove the bolt.

    7. Disconnect the antenna cord connector and detach the 2 clamps.

    8. B001YHCE03
      *1 Rear Right Side

      Disconnect the antenna cord connector.

    9. B001ZFTE04
      *1 Rear Left Side

      Disconnect the washer hose.

    10. for 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 2 clips, 2 guides and 16 fasteners.

      B001Z3AE02
      for 3 Person Seat Type Rear No. 2 Seat
      *1 Guide

    11. except 3 Person Seat Type Rear No. 2 Seat:

      Detach the 12 claws, 3 clips, 2 guides and 16 fasteners.

      B001YECE02
      except 3 Person Seat Type Rear No. 2 Seat
      *1 Guide
    12. B001X4D

      Remove the headlining from the rear of the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when taking it out.

  50. REMOVE FRONT ROOF SIDE RAIL GARNISH LH

    B001W7QE03
    *1 Cut Off Position

    1. Detach the 3 clips.

    2. Cut off the 3 clips and remove the roof side rail garnish.

    3. Remove 3 clips from the vehicle body.

  51. REMOVE FRONT ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  52. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    B001ZAH

    1. Remove the front door opening trim weatherstrip.

  53. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  54. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    B001WE3

    1. Remove the rear door opening trim weatherstrip.

  55. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedures described for the LH side.

  56. REMOVE BACK DOOR WEATHERSTRIP

    B001VQ9

    1. Remove the back door weatherstrip.

  57. REMOVE FRONT DOOR SCUFF PLATE OUTSIDE LH

    B001WTME03
    *1 Protective Tape

    1. Put protective tape around the front door scuff plate outside.

    2. Detach the 4 clips and remove the front door scuff plate outside.

  58. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  59. REMOVE REAR DOOR SCUFF PLATE OUTSIDE LH

    B001X9UE03
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate outside.

    2. Detach the 3 clips and remove the rear door scuff plate outside.

  60. REMOVE REAR DOOR SCUFF PLATE OUTSIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  61. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001YT2

    1. Detach the 6 claws of the plate, and slide the plate in the direction of the arrow to remove it.

  62. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  63. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    B001ZQX

    1. Detach the 6 claws and remove the plate.

  64. REMOVE REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  65. REMOVE ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YIH

    1. Detach the 7 claws and remove the cover.

  66. REMOVE ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  67. REMOVE REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001ZV4E01
    *1 Spring Nut

    Tech Tips

    Use the same procedure to remove the hanger on the other side.


    1. Remove the 2 spring nuts and hanger.

  68. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER LH

    B001Z0KE01
    *1 Spring Nut

    1. Remove the 2 spring nuts and hanger.

  69. REMOVE REAR NO. 2 SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedures described for the LH side.

  70. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY LH

    B002038

    1. w/ Rear Heater:

      Remove the 8 screws and duct.

    2. B001X84

      Remove the 7 screws.

    3. Detach the 4 claws and remove the quarter trim cover.

  71. REMOVE QUARTER TRIM COVER SUB-ASSEMBLY RH

    B001ZLG

    1. Remove the 7 screws.

    2. Detach the 4 claws and remove the quarter trim cover.

  72. REMOVE NO. 2 CUP HOLDER

    B001XWJ

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the cup holder.

  73. REMOVE NO. 1 CUP HOLDER

    B001XCS

    1. Remove the 5 screws.

    2. Detach the 3 claws and remove the cup holder.

  74. REMOVE NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001YPJ

    1. Detach the 4 claws and remove the cover.

  75. REMOVE NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    B001VTB

    1. Remove the 6 screws and duct.

    2. B001XGH

      Detach the 4 claws and remove the cover.

  76. REMOVE NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

    B001Z9U

    1. Detach the 4 claws and remove the cover.

  77. REMOVE NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

    Tech Tips

    Use the same procedures described for the LH side.

  78. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

  79. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  80. REMOVE REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    B001YAE

    1. Detach the 6 clips and remove the rear No. 2 seat cover bezel.

  81. REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the rear No. 2 seat cover bezel.

  82. REMOVE QUARTER TRIM COVER LH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    B001VOU

    1. Detach the 6 clips and remove the quarter trim cover.

  83. REMOVE QUARTER TRIM COVER RH (w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type)

    Tech Tips

    Use the same procedures described for the LH side.

  84. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH


    1. Remove the quarter trim lid.

  85. REMOVE SIDE TRIM BOX COVER


    1. Remove the side trim box cover.

  86. REMOVE SIDE TRIM BOX

    B001Z04

    1. Remove the 9 screws and side trim box.

  87. REMOVE NO. 2 MULTIPLEX NETWORK BODY ECU

    A01X4AI

    1. Disconnect the 2 connectors.

    2. Remove the bolt and multiplex network body ECU.