FRONT AIR CONDITIONING UNIT(for LHD) REMOVAL

CAUTION / NOTICE / HINT

Note

Set to recirculation mode before removing the air conditioning filter.

PROCEDURE


  1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. for Standard:

      Click here

    2. w/ Winch:

      Click here

  2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. for Standard:

      Click here

    2. w/ Winch:

      Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. for 1GR-FE:

      Click here

    2. for 1UR-FE:

      Click here

    3. for 3UR-FE:

      Click here

    4. for 1VD-FTV:

      Click here

  4. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  5. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

    Click here

  6. DRAIN ENGINE COOLANT


    1. for 1GR-FE:

      Click here

    2. for 1UR-FE:

      Click here

    3. for 3UR-FE:

      Click here

    4. for 1VD-FTV:

      Click here

  7. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  8. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  9. DISCONNECT AIR CONDITIONING TUBE ASSEMBLY


    1. B001ZK1E02
      Text in Illustration
      *1 Plate

      Remove the bolt.

    2. Detach the plate as shown in the illustration.

    3. B001X8LE02
      Text in Illustration
      *a Disconnect tube by hand

      Disconnect the air conditioning tube assembly.

      Note


      • Do not use a screwdriver or similar tool to disconnect the tube.

      • Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

    4. Remove the 2 O-rings from the air conditioning tube assembly.

  10. DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE


    1. Using pliers, grip the claws of the clips and slide the 2 clips.

    2. Disconnect the 2 heater water hoses.

      B00201PE01
      Text in Illustration
      *A for 1GR-FE *B for 1VD-FTE
      *C for 1UR-FE, for 3UR-FE - -

  11. REMOVE FRONT WIPER MOTOR AND BRACKET

    Click here

  12. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  13. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

    B001YJ7

    1. Remove the clip.

    2. Detach the 2 claws and remove the duct.

  14. REMOVE STEERING COLUMN ASSEMBLY


    1. for Power Tilt and Power Telescopic Steering Column:

      Click here

    2. for Manual Tilt and Manual Telescopic Steering Column:

      Click here

  15. REMOVE HEATER TO REGISTER DUCT ASSEMBLY


    1. Remove the 3 clips.

    2. Detach the 2 claws and remove the duct.

      B001XPI

  16. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


    1. Disconnect the 17 clamps.

    2. Remove the 8 nuts, 6 bolts, connectors and wire harness

      B001XB1

    3. Remove the instrument panel reinforcement.


      1. for Driver Side:

        Remove the 3 caps and 3 bolts.

      2. for Passenger Side:

        Remove the 2 caps.

      3. for Passenger Side:

        Using a T40 "TORX" socket, remove the 2 "TORX" bolts.

        Tech Tips

        When removing the bolts, the collars may come off with the bolts.

      4. for Passenger Side:

        Using a 12 mm hexagon wrench, remove the 2 collars.

      5. Remove the 7 bolts, screw and instrument panel reinforcement.

        B001ZAZ

  17. REMOVE AIR CONDITIONING HOSE AND ACCESSORY (w/ Cool Box)

    B001WA9

    1. Remove the bolt.

    2. Using SST, remove the piping clamp.

      SST
      09870-00025

      1. B001X44E02

        Attach SST to the piping clamp.

        Tech Tips

        Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.

      2. B001WKGE04

        Push down SST and release the clamp lock.

        Note

        Be careful not to deform the tubes when pushing SST.

      3. Pull SST slightly and push the release lever, then remove the piping clamp with SST.

      4. Remove the piping clamp from SST.

        Text in Illustration
        *1 Release Lever
        *a Push
        *b Pull

    3. Disconnect the hose and accessory from the liquid tube to remove it.

      Note

      Cap the open fittings immediately to keep moisture or dirt out of the system.

    4. Remove the 2 O-rings from the air conditioner hose and accessory.

  18. REMOVE AIR CONDITIONING UNIT


    1. B001ZTX

      Remove the 2 nuts and air conditioning unit.