Click here

AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System), Diagnostic DTC:B1488/88

Click here
Click here
DTC Code DTC Name
B1488/88 Rear Air Mix Damper Control Servo Motor Circuit on Front Passenger Side
Click here

DESCRIPTION


The rear air mix damper servo motor RH*1 or LH*2 sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air mix damper to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the blown air.

Tip:

Confirm that no mechanical problem is present because this trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code DTC Detection Condition Trouble Area
B1488/88 The rear air mix damper position does not change even if the air conditioning amplifier assembly operates the air mix damper servo motor RH*1 or LH*2.

  • Rear air mix damper servo motor RH*1

  • Rear air mix damper servo motor LH*2

  • No. 2 air conditioning harness assembly

  • Harness or connector

  • Air conditioning amplifier assembly
Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (A/M SERVO TARG PULSE [REAR P], A/M SERVO ACTUAL PULSE [REAR P]) (REAR AIR MIX DAMPER SERVO MOTOR)


    • *1: for LHD

    • *2: for RHD


    1. Use the Data List to check if the mode damper servo motor RH*1 or LH*2 is functioning properly (Click here).

      Table 1. Air Conditioner
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      A/M Servo Targ Pulse (Rear P) Rear air mix damper servo motor RH*1 or LH*2 target pulse / Min.: 128, Max.: 383
      • for LHD:

      • MAX COLD: 258 (pulse)

      • MAX HOT: 213 (pulse)


      • for RHD:

      • MAX COLD: 254 (pulse)

      • MAX HOT: 299 (pulse)

      • Displayed between 213 and 258 pulse (for LHD)

      • Displayed between 254 and 299 pulse (for RHD)

      • Rear air mix damper servo motor RH*1 or LH*2 system malfunction
      A/M Servo Actual Pulse (Rear P) Rear air mix damper servo motor RH*1 or LH*2 target pulse / Min.: 128, Max.: 383
      • for LHD:

      • MAX COLD: 258 (pulse)

      • MAX HOT: 213 (pulse)


      • for RHD:

      • MAX COLD: 254 (pulse)

      • MAX HOT: 299 (pulse)

      • Displayed between 213 and 258 pulse (for LHD)

      • Displayed between 254 and 299 pulse (for RHD)

      • Rear air mix damper servo motor RH*1 or LH*2 system malfunction
      OK
      When the rear temperature adjustment switch for front passenger side is turned from MAX COLD to MAX HOT, the actual pulse changes following the target pulse.
      Table 2. Result
      Result Proceed to
      Target pulse changes but actual pulse does not change A
      Target pulse and actual pulse do not change B
      Actual pulse changes following the target pulse (When troubleshooting according to the DTC) C
      Actual pulse changes following the target pulse (When troubleshooting according to Problem Symptoms Table) D

  2. Click here

    CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY- AIR CONDITIONING AMPLIFIER ASSEMBLY)


    1. Disconnect the K19 No. 2 air conditioning harness assembly connector.

    2. Disconnect the E36 air conditioning amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K19-2 (RBUG) - E36-12 (RBUG) Always Below 1 Ω
      K19-3 (RBUS) - E36-13 (RBUS) Always Below 1 Ω
      K19-4 (RBBU) - E36-14 (RBBU) Always Below 1 Ω
      K19-2 (RBUG) or E36-12 (RBUG) - Body ground Always 10 kΩ or higher
      K19-3 (RBUS) or E36-13 (RBUS) - Body ground Always 10 kΩ or higher
      K19-4 (RBBU) or E36-14 (RBBU) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK REAR AIR MIX DAMPER SERVO MOTOR


    1. Replace the rear air mix damper servo motor RH*1 or LH*2 (Click here).


      • *1: for LHD

      • *2: for RHD

      Tip:

      Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a normal one.

    2. Clear the DTCs (Click here).

    3. Check for DTCs (Click here).

      OK
      DTC B1488/88 is not output.

    • OK

      END (REAR DAMPER SERVO MOTOR [for Front Passenger Side] WAS DEFECTIVE)

    • NGClick here
  4. Click here

    CHECK NO. 2 AIR CONDITIONING HARNESS ASSEMBLY


    1. Replace the No. 2 air conditioning harness assembly with new or known good one (Click here).

    2. Clear the DTCs (Click here).

    3. Check for DTCs (Click here).

      OK
      DTC B1488/88 is not output.

    • OK

      END (NO. 2 AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)

    • NG

      REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

  5. Click here

    CHECK FOR DTC


    1. Clear the DTCs (Click here).

    2. Check for DTCs (Click here).

      OK
      DTC B1488/88 is not output.

    • OK

      USE SIMULATION METHOD TO CHECK (Click here)

    • NG

      REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)