Click here

REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side) REASSEMBLY

Click here
Click here

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    INSTALL REAR SEAT LOCK CONTROL LEVER LH


    1. Install the lock control lever with the bolt.

      13 N*m 133 kgf*cm 10 ft.*lbf
  2. Click here

    INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf

    3. Using a T40 "TORX" socket, tighten the bolt.

      21 N*m 214 kgf*cm 15 ft.*lbf
  3. Click here

    INSTALL NO. 1 SEAT LEG ASSEMBLY LH


    1. Using a T40 "TORX" socket, install the seat leg assembly with the 2 bolts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  4. Click here

    INSTALL REAR SEAT INNER BELT ASSEMBLY

    Click here

  5. Click here

    INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    1. Attach the 2 claws to install the seat heater control.

  6. Click here

    INSTALL REAR SEAT CUSHION HOLDER BRACKET LH (w/ Seat Heater System)


    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  7. Click here

    INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY


    1. B0010ZVE04
      Table 1.
      *1 Cable Tie

      Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. Connect the cable and install a new cable tie.

    4. B001120

      Install the lower seat track bracket with the 2 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  8. Click here

    INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY


    1. Install the 2 fold seat lock control cables.

    2. Attach the 2 cable clamps to connect the 2 cables.

  9. Click here

    INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


    1. B0010ZY

      Install the lower seatback cover.

    2. B00116N

      Temporarily install the seatback frame with the 4 bolts.

    3. LH Side:

      Using a T40 "TORX" socket, tighten the 2 bolts.

      42 N*m 428 kgf*cm 31 ft.*lbf

    4. RH Side:

      Using a T55 "TORX" socket, tighten the 2 bolts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  10. Click here

    INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY


    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. Click here

    INSTALL RECLINING ADJUSTING CABLE ASSEMBLY LH


    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  12. Click here

    INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    Click here

  13. Click here

    INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

    Click here

  14. Click here

    INSTALL REAR LOWER SEATBACK COVER SUB-ASSEMBLY LH


    1. Attach the 4 claws to install the cover.

    2. Install the 4 screws.

  15. Click here

    INSTALL REAR SEATBACK HINGE COVER LH


    1. Attach the claw to install the cover.

    2. Install the screw.

  16. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. Attach the claw to install the cover.

    2. Install the screw.

  17. Click here

    INSTALL REAR NO. 2 SEAT RECLINING COVER LH


    1. Attach the clamp to install the cover.

    2. Install the screw.

  18. Click here

    INSTALL REAR SEAT RECLINING COVER LH


    1. Attach the claw to install the cover.

    2. Install the screw.

  19. Click here

    INSTALL CUP HOLDER ASSEMBLY (w/ Center Armrest)


    1. A01X6GB

      Attach the 2 clips to install the cup holder.

    2. A01XAJ2

      Install the 2 screws.

  20. Click here

    INSTALL NO. 1 SEAT ARMREST PLATE (w/ Center Armrest)


    1. Attach the 2 claws and 4 clips to install the 2 armrest plates.

  21. Click here

    INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (w/ Center Armrest)

  22. Click here

    INSTALL REAR CENTER SEAT ARMREST ASSEMBLY (w/ Center Armrest)


    1. Using a T40 "TORX" socket, install the center seat armrest with the 2 bolts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  23. Click here

    INSTALL SEATBACK STOPPER PLATE


    1. w/ Center Armrest:


      1. Install the bush to the stopper plate.

      2. A01XBD7

        Temporarily install the stopper plate with the 3 bolts.

      3. Using a T40 "TORX" socket, tighten the 2 bolts.

        42 N*m 428 kgf*cm 31 ft.*lbf

      4. Tighten the bolt.

        15 N*m 153 kgf*cm 11 ft.*lbf

    2. w/o Center Armrest:


      1. Install the bush to the stopper plate.

      2. B00118D

        Temporarily install the stopper plate with the 3 bolts.

      3. Using a T40 "TORX" socket, tighten the 2 bolts.

        42 N*m 428 kgf*cm 31 ft.*lbf

      4. Tighten the bolt.

        15 N*m 153 kgf*cm 11 ft.*lbf
  24. Click here

    INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    1. B0010VCE10
      Table 2.
      *1 Name Stamp

      Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad LH.

    2. Install the seatback heater with new tack pins.

  25. Click here

    INSTALL REAR SEPARATE TYPE SEATBACK COVER


    1. B001103E01
      Table 3.
      *1 Hog Ring Pliers

      w/ Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B00112YE01
      Table 4.
      *1 Hog Ring Pliers

      w/o Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. B00118V

      w/ Rear Seat Side Airbag:

      Connect the seatback cover bracket to the seatback pad.

  26. Click here

    INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. B001185

      w/ Center Armrest:

      Pull out the seat belt.

    3. B0010VV

      w/o Center Armrest:

      Pull out the seat belt.

    4. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    5. w/ Seat Heater System:

      Pass the seatback heater wire harness through the hole in the seatback.


      1. B0011AO
      2. B00112CE01
        Table 5.
        *1 Cable Tie

        Connect the seatback heater wire harness and install a new cable tie.

    6. B0010XC

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
      Note:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    7. B0010ULE01
      Table 6.
      *1 Hog Ring Pliers

      w/ Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

    8. B00114ZE01
      Table 7.
      *1 Hog Ring Pliers

      w/o Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

  27. Click here

    INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH


    1. Attach the 4 claws to install the cover.

    2. Install the screw.

  28. Click here

    INSTALL SHOULDER BELT ANCHOR COVER


    1. Attach the 2 claws to install the cover.

  29. Click here

    INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. B00117N

      w/ Center Armrest:

      Attach the 4 claws to install the 2 supports.

    2. B00115Z

      w/o Center Armrest:

      Attach the 8 claws to install the 4 supports.

  30. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY

  31. Click here

    INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. B0011A1

      w/ Center Armrest:


      1. Push the board down to attach the 2 claws on the bottom.

      2. Attach the 2 claws on the top of the board to install it.

    2. B0010SX

      w/o Center Armrest:


      1. Push the board down to attach the 3 claws on the bottom.

      2. Attach the 3 claws on the top of the board to install it.

  32. Click here

    INSTALL REAR SEATBACK COVER


    1. Attach the 4 claws to install the cover.

  33. Click here

    INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    1. B0010WHE10
      Table 8.
      *1 Name Stamp

      Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad LH.

    2. Install the seat cushion heater with new tack pins.

  34. Table 9. *1 Hog Ring Pliers
    Click here

    INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER


    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B0010W6E01
      Table 10.
      *1 Fastening Tape

      Attach the 3 pieces of fastening tape.

  35. Click here

    INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. B0010Z6

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. B0010WZ

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  36. Click here

    CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    Click here

  37. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    Click here

  38. Click here

    INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  39. Click here

    INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY


    1. B00110Y

      Attach the cable clamp to connect the cable.

    2. B0010WV

      Attach the 2 cable clamps to connect the 2 cables.

    3. B001142

      Install the seat track handle with the 2 screws.

  40. Click here

    INSTALL REAR SEAT UNDER TRAY COVER LH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  41. Click here

    INSTALL REAR SEAT CUSHION COVER RH


    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  42. Click here

    INSTALL NO. 1 SEAT CUSHION PLATE


    1. Attach the 3 claws to install the seat cushion plate.

  43. Click here

    INSTALL REAR UNDER SIDE COVER LH


    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. B00114P

      Attach the 10 claws.

  44. Click here

    INSTALL REAR SEATBACK STAY COVER LH


    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  45. Click here

    INSTALL SEAT BELT ANCHOR COVER CAP


    1. B001174

      Install the anchor cover cap with the screw.

    2. B0010XM

      Attach the claw to close the cap.

  46. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  47. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. B00112S

      Attach the cable clamp to connect the cable.

    2. B00110W

      Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  48. Click here

    INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach 2 claws to close the protector.

    2. B001107

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. B0010VF

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  49. Click here

    INSTALL REAR SEAT SIDE HINGE MALE COVER RH


    1. B00117D

      Attach the clip to install the cover.

  50. Click here

    INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  51. Click here

    INSTALL REAR SEAT SIDE HINGE FEMALE COVER


    1. B00111F

      Attach the 6 claws to install the 2 covers.

  52. Click here

    INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  53. Click here

    INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. B001101

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. B001158

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  54. Click here

    INSTALL NO. 1 SEAT CUSHION COVER


    1. Attach the 4 claws to install the 2 covers.

  55. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER RH


    1. Attach the 2 claws to install the cover.

  56. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER LH


    1. Attach the 2 claws to install the cover.

  57. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  58. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  59. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. Install the release handle with the screw.

  60. Click here

    INSTALL SEAT ADJUSTER BOLT COVER


    1. Attach the 2 claws to install the cover.