REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 60 Side) REMOVAL

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   PRECAUTION

   Note:

   After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

2. Click here

   DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

   Note:

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

3. Click here

   REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER

   
   

   1. Using a screwdriver, detach the 6 claws and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

4. Click here

   REMOVE REAR NO. 5 SEAT CUSHION HINGE COVER

   
   

   1. Using a screwdriver, detach the 7 claws and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

5. Click here

   REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER

   
   
   1. 

      Operate the reclining adjuster release handle to move the seat into the position shown in the illustration.

   2. 

      Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

6. Click here

   REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER

   
   
   1. 

      Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.

      Tip:

      Tape the screwdriver tip before use.

7. Click here

   REMOVE REAR NO. 1 SEAT ASSEMBLY LH

   
   
   1. 

      w/ Rear Seat Side Airbag:

      Disconnect the connector.

   2. w/ Seat Heater System:

      Disconnect the connector.

   3. 

      Remove the 4 bolts and seat assembly.

      Note:

      Be careful not to damage the vehicle body.

8. Click here

   REMOVE REAR NO. 1 SEAT ASSEMBLY RH

   
   

   1. Remove the rear No. 1 seat assembly RH (Click here).

9. Click here

   REMOVE REAR NO. 1 SEAT PROTECTOR

   
   
   1. 

      Detach the 10 claws and remove the 2 seat protectors.

10. Click here

    REMOVE REAR NO. 2 SEAT PROTECTOR

    
    
    1. 

       Detach the 10 claws and remove the 2 seat protectors.

11. Click here

    REMOVE REAR STEP COVER

    Click here

12. Click here

    REMOVE REAR DOOR SCUFF PLATE LH

    Click here

13. Click here

    REMOVE REAR DOOR SCUFF PLATE RH

    Click here

14. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY

    
    

    1. for Face to Face Seat Type:

       Remove the rear No. 2 seat assembly (Click here).

    2. except Face to Face Seat Type:

       Remove the rear No. 2 seat assembly (Click here).

15. Click here

    REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    Click here

16. Click here

    REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

17. Click here

    REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    
    

    1. w/ Sliding Roof:

       Remove the front quarter trim panel assembly LH (Click here).

    2. w/o Sliding Roof:

       Remove the front quarter trim panel assembly LH (Click here).

18. Click here

    REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    
    

    1. w/ Sliding Roof:

       Remove the front quarter trim panel assembly RH (Click here).

    2. w/o Sliding Roof:

       Remove the front quarter trim panel assembly RH (Click here).

19. Click here

    REMOVE AIR DUCT PLUG (w/ Rear Air Conditioning System)

    Click here

20. Click here

    REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

    Click here

21. Click here

    REMOVE FRONT FLOOR CARPET ASSEMBLY

    Click here

22. Click here

    REMOVE REAR NO. 6 AIR DUCT (w/ Rear Air Conditioning System)

    Click here

23. Table 1. *1 RH Side: *2 LH Side:
    Click here

    REMOVE REAR SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY

    
    

    1. Remove the 10 bolts and 4 lock strikers.