REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 40 Side) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL REAR SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY


    1. Install the 4 strikers with the 10 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
      B001W30E01
      *1 RH Side:
      *2 LH Side:

  2. INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Conditioning System)

    Click here

  3. INSTALL FRONT FLOOR CARPET ASSEMBLY

    Click here

  4. INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

    Click here

  5. INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System)

    Click here

  6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


    1. w/ Sliding Roof:

      Install the front quarter trim panel assembly LH Click here.

    2. w/o Sliding Roof:

      Install the front quarter trim panel assembly LH Click here.

  7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH


    1. w/ Sliding Roof:

      Install the front quarter trim panel assembly RH Click here.

    2. w/o Sliding Roof:

      Install the front quarter trim panel assembly RH Click here.

  8. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

    Click here

  9. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    Click here

  10. INSTALL REAR NO. 2 SEAT ASSEMBLY


    1. for Face to Face Seat Type:

      Install the rear No. 2 seat assembly Click here.

    2. except Face to Face Seat Type:

      Install the rear No. 2 seat assembly Click here.

  11. INSTALL REAR DOOR SCUFF PLATE LH

    Click here

  12. INSTALL REAR DOOR SCUFF PLATE RH

    Click here

  13. INSTALL REAR STEP COVER

    Click here

  14. INSTALL REAR NO. 2 SEAT PROTECTOR

    B001WY4E01

    1. Attach the 10 claws to install the 2 seat protectors.

  15. INSTALL REAR NO. 1 SEAT PROTECTOR

    B001XB3E01

    1. Attach the 10 claws to install the 2 seat protectors.

  16. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly LH Click here.

  17. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

    B001XOQE01

    1. Temporarily install the seat assembly with the 4 bolts.

      Note

      Be careful not to damage the vehicle body.

    2. Tighten the bolts in the order shown in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
    3. B001WA1

      w/ Rear Seat Side Airbag:

      Connect the connector.

    4. w/ Seat Heater System:

      Connect the connector.

  18. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

    B001VYJ

    1. Attach the 2 clips and 2 claws to install the cover.

  19. INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

    B001W9D

    1. Attach the 2 clips and 2 claws to install the cover.

  20. INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER


    1. Return the seat to the upright position.

    2. B001WR4

      Attach the 7 claws to install the cover.

  21. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

    B001Y77

    1. Attach the 6 claws to install the cover.

  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  23. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  24. INSPECT REAR NO. 1 SEAT ASSEMBLY RH


    1. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the ignition switch to ON.

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.