REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type 40 Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL REAR NO. 1 SEAT LOCK CONTROL LEVER

    A01X2M4

    1. Install the lock control lever with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  2. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

    A01WZ83

    1. Temporarily install the seat cushion frame with the 5 nuts and bolt.

    2. Tighten the 5 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Using a T40 "TORX" socket, tighten the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

    Click here

  4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)

    B00117U

    1. Attach the 2 claws to install the seat heater control.

  5. INSTALL REAR SEAT CUSHION HOLDER BRACKET RH (w/ Seat Heater System)

    A01X2T1

    1. Install the holder bracket with the 2 screws.

    2. Connect the seat wire connector.

  6. INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

    A01WZR9

    1. Attach the clamp to install the seat lock cable.

    2. Attach the 3 cable clamps to connect the 3 cables.

    3. A01X8AZ

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    4. B001120

      Install the lower seat track bracket with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

    A01X8J3

    1. Install the 2 fold seat lock control cables.

    2. Attach the 2 cable clamps to connect the 2 cables.

  8. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH

    A01WYVA

    1. Temporarily install the seatback frame with the 4 bolts.

    2. Using a T40 "TORX" socket, tighten the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

    A01X4FN

    1. Attach the clamp to install the lock control cable.

    2. Attach the 2 cable clamps to connect the cable.

  10. INSTALL RECLINING ADJUSTING CABLE ASSEMBLY RH

    A01WZ8H

    1. Attach the clamp to install the adjusting cable.

    2. Attach the 2 cable clamps to connect the cable.

  11. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A01X89L

    1. Attach the claw to install the cover.

    2. Install the screw.

  12. INSTALL REAR NO. 2 SEAT RECLINING COVER LH

    B00110C

    1. Attach the clamp to install the cover.

    2. Install the screw.

  13. INSTALL REAR SEAT RECLINING COVER RH

    B0010XJ

    1. Attach the claw to install the cover.

    2. Install the screw.

  14. INSTALL REAR SEAT RECLINING COVER LH


    1. Attach the claw to install the cover.

    2. Install the screw.

  15. INSTALL REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)


    1. B0010VCE10
      *1 Name Stamp

      Set the rear seatback heater assembly onto the rear separate type seatback cover so that the name stamp is facing the rear seatback pad RH.

    2. Install the seatback heater with new tack pins.

  16. INSTALL REAR SEPARATE TYPE SEATBACK COVER

    B00119HE01
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seatback cover with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01X8QW

      w/ Rear Seat Side Airbag:

      Connect the seatback cover bracket to the seatback pad.

  17. INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    3. w/ Seat Heater System:


      1. A01WYXO

        Pass the seatback heater wire harness through the hole in the seatback.

      2. B0010VRE01
        *1 Cable Tie

        Connect the seatback heater wire harness and install a new cable tie.

    4. A01X8BZ

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      CAUTION:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    5. B00119JE01
      *1 Hog Ring Pliers

      Using hog ring pliers, install new hog rings to the seatback frame.

  18. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    B00117N

    1. Attach the 4 claws to install the 2 supports.

  19. INSTALL REAR SEAT HEADREST ASSEMBLY

  20. INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH

    A01XAXH

    1. Push the board down to attach the 2 claws on the bottom.

    2. Attach the 2 claws on the top of the board to install it.

  21. INSTALL REAR SEATBACK COVER

    B00111H

    1. Attach the 4 claws to install the cover.

  22. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)


    1. B0010WHE10
      *1 Name Stamp

      Set the rear seat cushion heater assembly onto the rear separate type seat cushion cover so that the name stamp is facing the rear seat cushion pad RH.

    2. Install the seat cushion heater with new tack pins.

  23. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    B00119XE01
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. B001157E01
      *1 Fastening Tape

      Attach the 3 pieces of fastening tape.

  24. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A01XB62

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A01X1WM

        Connect the 2 seat heater connectors.

    4. w/ Rear Seat Side Airbag:

      Attach the side airbag wire harness clamps.

  25. INSTALL FOLD SEAT LOCK CONTROL CABLE SUB-ASSEMBLY

  26. INSTALL REAR SEAT TRACK HANDLE SUB-ASSEMBLY


    1. B00110Y

      Attach the cable clamp to connect the cable.

    2. B0010WV

      Attach the 2 cable clamps to connect the 2 cables.

    3. B001142

      Install the seat track handle with the 2 screws.

  27. INSTALL REAR SEAT UNDER TRAY COVER RH

    B0010UA

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  28. INSTALL NO. 1 SEAT CUSHION PLATE

    B00117H

    1. Attach the 3 claws to install the seat cushion plate.

  29. INSTALL REAR UNDER SIDE COVER LH

    A01X5VH

    1. Attach the 2 claws and clip to install the cover.

    2. Install the 5 screws.

  30. INSTALL REAR SEAT COVER

    A01X4RS

    1. Attach the 2 claws to install the cover.

    2. Install the 3 screws.

    3. A01X3WE

      Attach the 12 claws.

  31. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. B00112S

      Attach the cable clamp to connect the cable.

    2. A01X5I6

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  32. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

    A01X2R6

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  33. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A01X5PY

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A01X40C

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  34. INSTALL REAR SEAT SIDE HINGE MALE COVER RH

    B00117D

    1. Attach the clip to install the cover.

  35. INSTALL REAR SEAT SIDE HINGE MALE COVER LH


    1. Attach the clip to install the cover.

  36. INSTALL REAR SEAT SIDE HINGE FEMALE COVER

    B00111F

    1. Attach the 6 claws to install the 2 covers.

  37. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY


    1. Install the fold seat stopper band to the seat leg side cover.

  38. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A01X3A8

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A01X0XI

      Attach the 3 claws to install the seat leg side cover.

    3. Install the 4 screws.

  39. INSTALL NO. 1 SEAT CUSHION COVER

    A01WZX2

    1. Attach the 4 claws to install the 2 covers.

  40. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A01XAZA

    1. Attach the 2 claws to install the cover.

  41. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01XB6J

    1. Attach the 2 claws to install the cover.

  42. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A01XAFO

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  43. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    B00116ZE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  44. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A01X9A7

    1. Install the release handle with the screw.

  45. INSTALL SEAT ADJUSTER BOLT COVER

    A01XAAK

    1. Attach the 2 claws to install the cover.