FRONT SEAT ASSEMBLY(for Bench Seat Type) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL FRONT SEAT OUTER TRACK ASSEMBLY RH


    1. Using a T40 "TORX" socket wrench, install the front seat outer track assembly RH together with the front seat reinforcement with the 5 "TORX" bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
  2. INSTALL FRONT SEAT INNER TRACK ASSEMBLY RH


    1. Using a T40 "TORX" socket wrench, install the front seat inner track assembly RH with the 5 "TORX" bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    2. A01X9HO

      Attach the 2 springs to install the seat track adjusting handle as shown in the illustration.

  3. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

    A01X9JN

    1. Attach the claw to install the front seat lower cushion shield RH.

  4. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH


    1. Install the reclining adjuster outside cover LH with the screw.

  5. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. Attach the guide.

    2. Install the reclining adjuster inside cover LH with the screw.

  7. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL FRONT SEATBACK PROTECTOR

    A01X1D9E01
    Text in Illustration
    *1 Double-sided Tape

    1. Apply double-sided tape as shown in the illustration.

    2. Install the front seatback protector.

  9. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

    A01X0T3E01
    Text in Illustration
    *1 Hog Ring
    *2 Fastening Tape
    *3 Hog Ring Pliers

    1. Attach the fastening tape to temporarily install the separate type front seatback cover to the separate type front seatback pad.

    2. Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  10. INSTALL SEATBACK COVER WITH PAD


    1. Set the seatback cover with pad in place.

    2. Attach the 4 claws to install the 2 front seat headrest supports.

    3. Attach the fastening tape.

    4. Attach the 2 hooks.

    5. A01X4OPE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    6. A01X4LNE01
      Text in Illustration
      *1 Fastener
      *2 Hog Ring
      *3 Hog Ring Pliers

      Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    7. Close the 2 fasteners to install the seatback cover with pad.

  11. INSTALL FRONT SEAT INNER CUSHION SHIELD RH


    1. Attach the claw and clip to install the front seat inner cushion shield RH.

    2. Install the screw.

  12. INSTALL CENTER SEAT HINGE COVER


    1. Install the center seat hinge cover with the screw.

  13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

    A01X7U1E01
    Text in Illustration
    *1 Hog Ring Pliers

    1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  14. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the seat cushion cover with pad in place.

    2. A01X4JDE02
      Text in Illustration
      *1 Hog Ring
      *2 Hook
      *3 Hog Ring Pliers

      Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. Attach the hooks to install the seat cushion cover with pad.

  15. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR

    A01XAO5E01
    Text in Illustration
    *1 Cushion Edge Tab

    1. Install the 2 front seat cushion edge protectors.

    2. Return the 2 cushion edge tabs to their original positions.

      Note

      Be careful not to break the cushion edge tabs.

  16. INSTALL FRONT SEATBACK SIDE COVER SUB-ASSEMBLY RH

    A01X1B7

    1. Set the front seatback side cover sub-assembly RH in place.

      Note

      Be careful not to damage the cover.

    2. A01XB5H

      Install the front seatback inside pad RH.

    3. Attach the fastening tape to install the front seatback side cover sub-assembly RH.

      Note


      • Be careful not to damage the cover.

      • When attaching the fastening tape, avoid wrinkling the cover.

  17. INSTALL FRONT SEAT ARMREST HOLE BOARD COVER


    1. Install the front seat armrest hole board cover to the seat armrest assembly RH.

  18. INSTALL SEAT ARMREST ASSEMBLY RH


    1. Install the seat armrest assembly RH with the bolt.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
  19. INSTALL INNER SEAT BRACKET ASSEMBLY RH


    1. Install the inner seat bracket assembly RH with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
  20. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. Attach the hook to install the front seat lower cushion shield RH.

    2. Install the screw.

  21. INSTALL FRONT SEAT HINGE COVER RH


    1. Attach the 2 hooks to install the front seat hinge cover RH.

    2. Install the 2 screws.

  22. INSTALL FRONT SEAT HINGE KNOB

    A01X0JC

    1. Twist the front seat hinge knob in the direction indicated by the arrow to install it.

  23. INSTALL FRONT SEAT CUSHION SHIELD RH


    1. Attach the 2 guides and claw to install the front seat cushion shield RH.

    2. Install the 2 screws.

    3. Attach the 2 rubber bands.

  24. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A01XA44

    1. Attach the claw to install the reclining adjuster release handle RH.

  25. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

    Click here

  26. INSTALL SEAT ADJUSTER COVER CAP RH


    1. Install the 2 seat adjuster cover caps.