METER / GAUGE SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical, Powertrain or Chassis / (desired system) / Data List.

    5. According to the display on the GTS, read the Data List.

      Combination Meter
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tail Cancel SW TAIL cancel switch condition / ON or OFF

      ON: TAIL cancel switch on

      OFF: TAIL cancel switch off

      		 -
      ODO/TRIP Change SW Trip switch (ODO/TRIP switch) condition / ON or OFF

      ON: Trip switch (ODO/TRIP switch) pushed

      OFF: Trip switch (ODO/TRIP switch) not pushed

      		 -
      P-Seatbelt Buckle SW Front passenger side seat belt warning light request signal / ON or OFF

      ON: Tongue plate (for front passenger side) inserted

      OFF: Tongue plate (for front passenger side) not inserted

      		 -
      Vehicle Speed Meter Vehicle speed / Min.: 0 (0), Max.: 255 (158) Almost same as actual vehicle speed (when driving) Unit: km/h (mph)
      Engine Rpm Engine speed / Min.: 0, Max.: 12750 rpm Idling: 700 to 800 Unit: rpm
      Coolant Temperature Engine coolant temperature / Min.: -40 (-40), Max.: 140 (284) F After warming up: 80 to 105 (176 to 221)

      • Unit: °C (°F).

      • If the value is -40 (-40): The sensor circuit is open.

      • If the value is 140 (284): The sensor circuit is shorted.
      Washer Switch Washer switch / ON or OFF

      ON: Washer switch on

      OFF: Washer switch off

      		 -
      Reverse Range Switch (6MT) Reverse lamp switch / ON or OFF

      ON: Reverse lamp switch on

      OFF: Reverse lamp switch off

      		 -
      Integrated value for Maintenance Integrated value for Maintenance / Min: 0, Max, 25500 - -
      +B Voltage Value Battery voltage / Min.: 0 V, Max.: 25.5 V 11 to 14 V -
      Oil Level SW Engine oil level switch/ ON or OFF

      ON: Engine oil level low

      OFF: Engine oil level not low

      		 -
      Water Level SW Level warning switch/ ON or OFF

      ON: Level warning switch on

      OFF: Level warning switch off

      		 -
      Fuel Input Fuel sender gauge input / Min.: 0, Max.: 127.5 L

      Fuel receiver gauge indicates F: 83.7 L

      Fuel receiver gauge indicates 3/4: 66.5 L

      Fuel receiver gauge indicates 1/2: 49.5 L

      Fuel receiver gauge indicates 1/4: 31.2 L

      Fuel receiver gauge indicates E: 12.5 L

      		 Unit: L
      Sub Fuel Input Fuel sender gauge input / Min.: 0, Max.: 127.5 L

      Fuel receiver gauge indicates F: 34 L

      Fuel receiver gauge indicates 1/2: 24.5 L

      Fuel receiver gauge indicates E: 4 L

      		 Unit: L
      Ambient Temperature Outside temperature / Min: -40, Max: 87.5°C Outside temperature -
      Rheostat value Light control rheostat switch input / Min.: 0, Max.: 255 Light control rheostat switch is fully turned right (0) → fully turned left (255) -
      Multi Switch (Down) Steering pad switch (Down) / ON or OFF

      ON: Steering pad switch (Down) pushed

      OFF: Steering pad switch (Down) released

      		 -
      Multi Switch (Menu) Steering pad switch (Menu) / ON or OFF

      ON: Steering pad switch (Menu) pushed

      OFF: Steering pad switch (Menu) released

      		 -
      Multi Switch (Enter) Steering pad switch (Enter) / ON or OFF

      ON: Steering pad switch (Enter) pushed

      OFF: Steering pad switch (Enter) released

      		 -
      Multi Switch (Right) Steering pad switch (Right) / ON or OFF

      ON: Steering pad switch (Right) pushed

      OFF: Steering pad switch (Right) released

      		 -
      Multi Switch (Left) Steering pad switch (Left) / ON or OFF

      ON: Steering pad switch (Left) pushed

      OFF: Steering pad switch (Left) released

      		 -
      Multi Switch (Up) Steering pad switch (Up) / ON or OFF

      ON: Steering pad switch (Up) pushed

      OFF: Steering pad switch (Up) released

      		 -
      Fuel Filter Switch Fuel filter assembly (clogging switch) / ON or OFF

      ON: Fuel filter assembly (clogging switch) on

      OFF: Fuel filter assembly (clogging switch) off

      		 for 1VD-FTV
      Turn Signal Switch (Right) Turn signal switch (right) / ON or OFF

      ON: Turn signal switch (right) on

      OFF: Turn signal switch (right) off

      		 -
      Turn Signal Switch (Left) Turn signal switch (left) / ON or OFF

      ON: Turn signal switch (left) on

      OFF: Turn signal switch (left) off

      		 -
      Hazard Flasher Switch Hazard warning signal switch / ON or OFF

      ON: Hazard warning signal switch on

      OFF: Hazard warning signal switch off

      		 -
      Passenger Occupant Detection Switch Front passenger side occupant detection sensor / ON or OFF

      ON: Front passenger seat occupied

      OFF: Front passenger seat not occupied

      		 -
      Turn Switch Signal (Full Turn) Turn signal switch status / ON or OFF

      ON: Turn signal switch on (Full Turn)

      OFF: Turn signal switch off

      		 -
      Multi Switch (Back) Steering pad switch (Back) / ON or OFF

      ON: Steering pad switch (Back) pushed

      OFF: Steering pad switch (Back) released

      		 -
      Battery Charge Battery Charge / OK or NG

      OK: Battery is charged

      NG: Battery is not charged

      		 -
      Driver Side Seatbelt Warning Buzzer Driver seat belt warning buzzer / ON or OFF Customized value displayed -
      P-Seatbelt Warning Buzzer Front Passenger Side Seatbelt Warning Buzzer / OFF or ON Customized value displayed -
      ODO Display Time After IG OFF Setting Condition of the ODO display time after the ignition switch is turned off / 30s, 60s, 600s, OFF Customized value displayed -
      Lane Change Flashing Times Setting Lane change flashing times customize status / OFF, 3 , 4, 5, :6, 7 - This item is only to be used to display
      Flasher Sound Volume Adjustment Flasher sound volume customize status /Large, Medium, Small - This item is only to be used to display
      TPMS System Existence of function / with or without

      With: w/ Tire Pressure Warning System

      Without: w/o Tire Pressure Warning System

      		 -
      VGRS System Existence of function / with or without

      With: w/ VGRS System

      Without: w/o VGRS System

      		 -
      LDA System Existence of function / with or without

      With: w/ Lane Departure Alert System

      Without: w/o Lane Departure Alert System

      		 -
      PCS System Existence of function / with or without

      With: w/ Pre-collision System

      Without: w/o Pre-collision System

      		 -
      AHS System Existence of function / with or without

      With: w/ adaptive hi beam System

      Without: w/o adaptive hi beam System

      		 -
      Clearance Sonar System Existence of function / with or without

      With: w/ Clearance Sonar System

      Without: w/o Clearance Sonar System

      		 -
      Road Sign Assist System Existence of function / with or without

      With: w/ Road Sign Assistant System

      Without: w/o Road Sign Assistant System

      		 -
      Number of Trouble Code The number of the DTC currently stored / Min.: 0, Max.: 255 0 -
      Engine
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Engine Rpm Engine speed / Min.: 0, Max.: 16383.75 Idling: 700 to 800 Unit: rpm
      Vehicle Speed Meter Vehicle speed / Min.: 0 (0), Max.: 255 (158) Actual vehicle speed

      • Unit: km/h (mph)

      • The speed is indicated on the speedometer.
      Coolant Temperature*1

      Engine coolant temperature:

      Min.: -40°C, Max.: 140°C

      80 to 100°C (176 to 212):

      After warming up

      • If the value is -40°C (-40°F), The sensor circuit is open.

      • If the value is 140°C (284°F) or higher, The sensor circuit is shorted.
      Coolant Temperature*2

      Engine coolant temperature /

      Min.: -40°C, Max.: 140°C

      		 After warming up engine: 75 to 90°C (167 to 194°F)

      • If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

      • After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.

      Tech Tips

      *1: except 1VD-FTV

      *2: for 1VD-FTV

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (Combination Meter) / Active Test.

    5. According to the display on the GTS, perform the Active Test.

      Combination Meter
      Tester Display Test Part Control Range Diagnostic Note
      Speed Meter Operation*1 Speedometer 0, 40, 80, 120, 160, 200, 240 or 280

      Acceptable range (mph or km/h): [Control range → Speedometer display]


        for km/h (for Australia)

      • 40 → 41 to 45.5

      • 80 → 81.4 to 85.8

      • 120 → 122.1 to 126.8

      • 160 → 163 to 168.2

      • 200 → 203.9 to 209.5

      • 240 → 244.8 to 250.8


        for km/h (except Australia)

      • 40 → 41.7 to 46.2

      • 80 → 83.4 to 88.4

      • 120 → 125.1 to 130.6

      • 160 → 166.2 to 173.2

      • 200 → 207.7 to 215.7

      • 200 → 249.2 to 258


        for mph

      • 40 → 42 to 44.5

      • 80 → 83.1 to 87.1

      • 120 → 124.7 to 129.6

      Perform the test with the vehicle stopped and engine idling.
      Tachometer operation Tachometer 0, 1000, 2000, 3000, 4000, 5000, 6000 or 7000 Perform the test with the vehicle stopped and engine idling.
      Fuel Meter Operation Fuel receiver gauge EMPTY, 1/2, FULL Perform the test with the vehicle stopped and engine idling.
      Volt Meter Operation Voltmeter 0, 3, 6, 9, 12, 15 or 18 Perform the test with the vehicle stopped and engine idling.
      Oil Pressure Meter Operation Oil pressure receiver gauge LOW, 1/4, 1/2, 3/4 or HIGH Perform the test with the vehicle stopped and engine idling.
      A/T Indicator operation (1)*10 A/T indicator P, R, N, D, 4, 3, 2, L Perform the test with the vehicle stopped and engine idling.
      A/T Indicator operation (2)*10 A/T indicator 5, 6, 7, 8, S or M Perform the test with the vehicle stopped and engine idling.
      A/T Indicator operation (3)*10 A/T indicator D Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Airbag SRS warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Doors All Open All doors open light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Driver Side Seat Belt Driver side seat belt warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Front Passenger Side Seat Belt Passenger side seat belt warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp ABS ABS warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Charge CHARGE warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Slip SLIP indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Tail TAIL indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Head HEAD indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Fr FOG Fr. FOG indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Rr FOG*16 Rr. FOG indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Meter Display 1*2*14 All dots in the multi-information display ALL, 0, 1, 2, 3, 4, 5 or 6 Perform the test with the vehicle stopped and engine idling.
      Meter Display 2*2*14 All dots in the multi-information display 7, 8 or 9 Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Beam BEAM indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Precrash PCS indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Headlamp Auto Leveling Headlight Auto Leveling light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Fuel Low fuel warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. TRC OFF TRC OFF indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Tire Pressure Warning System Tire pressure warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. ECONO Eco driving indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp ECT PWR*3,*7 ECT PWR indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Cruise*7 Cruise control indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Brake Brake warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Master Warning*14 Master warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Park Parking brake warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. 2nd START*10 2nd START indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Ctr DIFF LOCK Center differential lock indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Rr DIFF LOCK Rear differential lock indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. 4LO 4LO indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. CRAWL*17 CRAWL indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. SET*3,*7 SET indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Radar Cruise Indicator*3 Radar cruise control indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. VSC TRC TRC OFF indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. VSC OFF VSC OFF indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Automatic High Beam Indicator*9 Automatic high beam indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      OFF Road Guidance Indicator Multi-terrain select indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      PPS Indicator PPS warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Turn Signal (Left) Indicator Turn L indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Turn Signal (Right) Indicator Turn R indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Check Engine Indicator MIL (Malfunction indicator lamp) ON or OFF Perform the test with the vehicle stopped and engine idling.
      Rr Inner Wheel Control Indicator Turn assist indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      BSM Control Indicator*18 BSM control indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      LDA Control Indicator*19 LDA control indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      RCTA Indicator*18 RCTA indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Water Temperature Meter Operation Engine coolant temperature receiver gauge LOW, NORMAL or HIGH Perform the test with the vehicle stopped and engine idling.
      A/T Oil Temperature Operation*10*13 A/T OIL TEMP warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Oil Level*13 Oil level warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat GLOW*5 Glow indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Lamp Washer*13 Washer level warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Indicat. Over Speed*14 Speed Limit indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Fuel Filter Indicator*5*13 Fuel sedimenter warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Headlight warning light*13 Headlight warning light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Smart System Indicator*13*15 Smart Key indicator light (Illuminated Green) ON or OFF Perform the test with the vehicle stopped and engine idling.
      Smart System Warning*13*15 Smart Key indicator light (Illuminated Yellow) ON or OFF Perform the test with the vehicle stopped and engine idling.
      Diesel Particulate Filter Warning*5*13 DPF indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Brake Override Indicator*13 Brake override indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.
      Go to Service Warning*13 Go to service indicator light ON or OFF Perform the test with the vehicle stopped and engine idling.

      Tech Tips

      *1:


      • The doors will be locked automatically when performing the speedometer Active Test. This is a normal function.

      • The displayed value has the same units (km/h, mph) as the main scale of the vehicle speedometer.

      • The needle position should be within the acceptable range.

      *2: If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end this Active Test and turn the ignition switch off.

      *3: w/ Dynamic Radar Cruise Control System

      *4: w/ Headlight Leveling

      *5: for 1VD-FTV

      *6: w/ VSC

      *7: w/ Cruise Control System

      *8: w/ Multi-terrain Select

      *9: w/ Automatic High Beam System

      *10: for Automatic Transmission

      *11: w/ Tire Pressure Warning System

      *12: w/ Multi-information Display

      *13: w/o Multi-information Display

      *14: for Middle East

      *15: w/ Entry and Start System

      *16: w/ Rear Fog light

      *17: w/ CRAWL control system

      *18: w/ Blind Spot Monitor System

      *19: w/ Lane Departure Alert System

    Main Body
    Tester Display Test Part Control Range Diagnostic Note
    Dimmer Signal Illumination dimming operation ON or OFF -