METER / GAUGE SYSTEM OPERATION CHECK


  1. INSPECT INDICATOR/WARNING LIGHT


    1. Check the following indicators and warning lights.

      w/o Multi-information Display
      Indicator/Warning Light Switch Condition Specified Condition
      A/T OIL TEMP warning light*1 Ignition switch off → ON Comes on for 3 seconds
      BRAKE warning light
      ABS warning light
      OIL LEVEL indicator light
      FUEL FILTER & SEDIMENTER indicator light*2
      SLIP indicator light*3
      VSC OFF indicator light*3
      WASHER indicator light
      RSCA OFF indicator light*4
      CRAWL indicator light*3
      SPEED LIMIT indicator light
      Eco driving indicator light
      TRC OFF indicator light*3
      Turn assist indicator light*3
      Multi-terrain select indicator light*5
      SRS warning light Ignition switch off → ON Comes on for 6 seconds
      CHARGE warning light Ignition switch off → ON Illuminates when ignition switch is turned to ON. Turns off when engine is started.
      MIL

      • *1: for Automatic Transmission

      • *2: for 1VD-FTV

      • *3: w/ VSC

      • *4: w/ Curtain Shield Airbag

      • *5: w/ Multi-terrain Select

    w/ Multi-information Display
    Indicator/Warning Light Switch Condition Specified Condition
    BRAKE warning light Ignition switch off → ON Comes on for 3 seconds
    ABS warning light
    SLIP indicator light
    RSCA OFF indicator light*1
    CRAWL indicator light
    SPEED LIMIT indicator light
    PCS indicator light*2
    Eco driving indicator light
    VSC OFF indicator light
    Turn assist indicator light
    Multi-terrain select indicator light*4
    Headlight beam level control system warning light*3
    Tire pressure warning light*5
    SRS warning light Ignition switch off → ON Comes on for 6 seconds
    CHARGE warning light Ignition switch off → ON Illuminates when ignition switch is turned to ON. Turns off when engine is started.
    MIL

    • *1: w/ Curtain Shield Airbag

    • *2: w/ Pre-crash Safety System

    • *3: w/ Headlight Leveling

    • *4: w/ Multi-terrain Select

    • *5: w/ Tire Pressure Warning System

  2. INSPECT SPEEDOMETER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

      If the result is not as specified, the speedometer may have a malfunction.

      Note

      Do not use worn, underinflated or overinflated tires, as the speedometer reading will be inaccurate.

    5. Check the deflection width of the speedometer indicator.

    6. INSPECT TACHOMETER


      1. Connect a tune-up tachometer, and start the engine.

      2. Compare the test results with the tachometer indicator.

    7. DC 13.5 V, at 25°C (77°F):
      Standard indication (rpm)

      Acceptable range

      Data in ( ) is for reference

      700 630 to 770
      1000 (900 to 1100)
      2000 (1850 to 2150)
      3000 2800 to 3200
      4000 (3800 to 4200)
      5000 4800 to 5200
      6000 (5750 to 6250)

If the result is not as specified, the tachometer may have a malfunction.

  • INSPECT METER/GAUGE


    1. Connect the intelligent tester to the DLC3.

    2. Perform Active Test Click here.

    3. INSPECT WARNING/INDICATOR LIGHT


      1. Connect the intelligent tester to the DLC3.

      2. Perform Active Test Click here.

    4. INSPECT ENGINE OIL LEVEL WARNING (except 3UR-FE)


      1. Turn the ignition switch to ON and warm up the engine at an engine speed of 2000 rpm or less until the coolant temperature reaches approximately 80°C (176°F) or more.

      2. Disconnect the engine oil level sensor connector for 40 seconds or more.

      3. Turn the ignition switch to ON and check the multi-information display.

    5. INSPECT MULTI-INFORMATION DISPLAY (w/ Multi-information Display)


      1. Connect the intelligent tester to the DLC3.

      2. Perform Active Test Click here.

        Tech Tips

        If this Active Test is being performed and the ignition switch is turned off and then ON, the A/T and ODO/TRIP display background may turn white. If this occurs, end Active Test and turn the ignition switch off.