THEFT DETERRENT SYSTEM(w/ Entry and Start System) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / (desired system) / Data List.

    5. According to the display on intelligent tester, read the "Data List".

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Intrusion sensor OFF

      Intrusion sensor cancel switch /

      ON or OFF

      ON: Intrusion sensor active (switch off)

      OFF: Intrusion sensor not active (switch on)

      		 -
      Intrusion sensor detection

      Intrusion sensor setting /

      ON or OFF

      ON: Moving object detected by sensor during arming preparation state to armed state

      OFF: No moving object detected by sensor

      		 -
      Tilt sensor detection

      Tilt sensor setting /

      ON or OFF

      ON: Tilt sensor set

      OFF: Tilt sensor not set

      		 -
      Hood Courtesy Switch

      Engine hood courtesy switch /

      ON or OFF

      ON: Engine hood open

      OFF: Engine hood closed

      		 -
      Warn By Horn

      Security horn /

      ON or OFF

      ON: Security horn sounding

      OFF: Security horn not sounding

      		 -
      Glass break sensor detection

      Glass breakage sensor detection /

      ON or OFF

      ON: Glass breakage sensor operates

      OFF: Glass breakage sensor does not operate

      		 -
      Pattern Glass Connection

      Pattern Glass Connection /

      OK or NG

      OK: Pattern glass connection

      NG: No pattern glass connection

      		 -
      Intrusion sensor 1 communication

      Intrusion sensor setting /

      OK or STOP

      OK: Intrusion sensor set

      STOP: Intrusion sensor not set

      		 -
      Tilt sensor communication

      Tilt sensor setting /

      OK or STOP

      OK: Tilt sensor set

      STOP: Tilt sensor not set

      		 -
      Tilt sensor OFF Switch

      Tilt sensor OFF switch /

      ON or OFF

      ON: Tilt sensor active (switch off)

      OFF: Tilt sensor not active (switch on)

      		 -
      # Codes Number of diagnostic trouble codes - -
      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door Courtesy SW Driver side door courtesy light switch signal / ON or OFF

      ON: Driver side door opened

      OFF: Driver side door closed

      		 -
      D Door Lock Pos SW Driver side door lock position switch signal / ON or OFF

      ON: Driver side door unlocked

      OFF: Driver side door locked

      		 -
      Door Key SW-Lock Door key linked lock switch signal / ON or OFF

      ON: Driver side door key cylinder turned to lock position

      OFF: Driver side door key cylinder not turned

      		 -
      D-Door Key SW-UL Door key linked unlock switch signal / ON or OFF

      ON: Driver side door key cylinder turned to unlock position

      OFF: Driver side door key cylinder not turned

      		 -
      P-Door Courtesy SW Front passenger side door courtesy light switch signal / ON or OFF

      ON: Front passenger side door opened

      OFF: Front passenger side door closed

      		 -
      P-Door Lock Pos SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door unlocked

      OFF: Front passenger side door locked

      		 -
      Door Lock SW-Lock Door manual lock switch signal / ON or OFF

      ON: Front passenger side door control switch on (LOCK)

      OFF: Front passenger side door control switch off

      		 -
      Door Unlock SW-Unlock Door manual unlock switch signal / ON or OFF

      ON: Front passenger side door control switch on (UNLOCK)

      OFF: Front passenger side door control switch off

      		 -
      RL Door Courtesy SW Rear LH side door courtesy light switch signal / ON or OFF

      ON: Rear LH side door opened

      OFF: Rear LH side door closed

      		 -
      RL-Door Lock Pos SW Rear LH side door lock position switch signal / ON or OFF

      ON: Rear LH side door unlocked

      OFF: Rear LH side door locked

      		 -
      RR Door Courtesy SW Rear RH side door courtesy light switch signal / ON or OFF

      ON: Rear RH side door opened

      OFF: Rear RH side door closed

      		 -
      RR-Door Lock Pos SW Rear RH side door lock position switch signal / ON or OFF

      ON: Rear RH side door unlocked

      OFF: Rear RH side door locked

      		 -
      Back Door Courtesy SW Back door courtesy light switch signal / ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      Back Door Open SW ON / OFF

      ON: Back door opener switch on

      OFF: Back door opener switch off

      		 -
      Back Door Open Permit / Prohibit

      PERMIT: Back door open available

      PROHIBIT: Back door open unavailable

      		 -
      IG SW ON / OFF

      ON: Engine switch is on (IG)

      OFF: Engine switch is off

      		 -
      ACC SW ON / OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Test allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Entry&Start / Active Test.

    5. According to the display on intelligent tester, perform the "Active Test".

      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Security Indicator Security indicator ON / OFF -
      Security Horn*1 Security horn ON / OFF -
      Security Horn2*2 Theft warning siren (self power siren) ON / OFF -
      Power For Tilt Sensor*3 Tilt sensor power supply ON / OFF -
      Power For Intrusion Sensor*3 Intrusion sensor power supply ON / OFF -

      Tech Tips

      *1: w/ Security Horn

      *2: w/ Theft Warning Siren (Self Power Siren)

      *3: w/ Intrusion Sensor