ENTRY AND START SYSTEM(for Start Function) Engine does not Start

DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. In addition, when the shift lever is in P*1 and the brake pedal*1 or clutch pedal*2 is depressed, the engine can be started by pressing the engine switch. If the steering is unlocked, the engine can also be started by pressing the engine switch with the shift lever in N and the brake pedal*1 or clutch pedal*2 depressed.


Tech Tips


  • When the certification ECU (smart key ECU assembly) is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode changes to on (IG).

  • When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.

Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Engine does not start

    Power Source Control

  • Stop Light Switch1

  • Steering Unlock Switch

  • Power Supply Condition

  • IG Relay Monitor(Inside)

  • IG Relay Monitor(Outside)

  • Latch Circuit

  • Shift P Signal*

  • Neutral SW/ Clutch SW

  • Starter Request Signal


    Entry&Start

  • Immobiliser

  • S Code Check

  • L Code Check

  • Engine Start Request


    Starting Control

  • Ignition

  • Starter SW

  • Shift Position P or N*

 -

WIRING DIAGRAM

Refer to "System Diagram" Click here

B001ZTOE01
B001VYTE06

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus:

    Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting Click here.

  • Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator assembly), ECM or ID code box (immobiliser code ECU), refer to the entry and start system (for Start Function) precaution Click here.

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

  • After completing repairs, confirm that the problem does not occur.

Tech Tips

If the brake pedal*1 or clutch pedal*2 is repeatedly depressed while the engine is stopped, the brake booster pressure is released and the force required to depress the brake pedal*1 or clutch pedal*2 to illuminate the stop lights increases.


  • *1: for Automatic Transmission

  • *2: for Manual Transmission

PROCEDURE


  1. CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY


    1. Press a switch of the electrical key transmitter sub-assembly.

      OK
      The electrical key transmitter sub-assembly LED illuminates.

    NG

    INSPECT TRANSMITTER BATTERY Click here

    OK

  2. READ VALUE USING GTS (KEY LOW BATTERY)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. According to the display on the GTS, read the Data List.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Key Low Battery Transmitter battery depleted/Yes or No

      Yes: Transmitter battery depleted

      No: Transmitter battery not depleted

      The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

      This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new).
      OK
      "No" is displayed in the Data List.

    NG

    REPLACE TRANSMITTER BATTERY Click here

    OK

  3. CHECK WAVE ENVIRONMENT


    1. If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

      Tech Tips

      Whether the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver.

      OK
      Engine starts.

    OK

    AFFECTED BY WAVE INTERFERENCE

    NG

  4. CHECK ENGINE SWITCH CONDITION


    1. Get into the vehicle while carrying an electrical key transmitter sub-assembly.

    2. for Automatic Transmission:

      Move the shift lever to P.

    3. With the brake pedal released*1 or clutch pedal*2, check that pressing the engine switch causes the power source mode to change.


      • *1: for Automatic Transmission

      • *2: for Manual Transmission

      Result
      Result Proceed to
      Off → on (ACC) → on (IG) → off A
      Power source mode does not change to on (ACC) and on (IG) B
      Power source mode changes to on (IG) but not to on (ACC) C
      Power source mode changes to on (ACC) but not to on (IG) D

    B

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG AND ACC) Click here

    C

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (ACC) Click here

    D

    GO TO POWER SOURCE MODE DOES NOT CHANGE TO ON (IG) Click here

    A

  5. READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT POSITION P OR N)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.

    5. According to the display on the GTS, read the Data List.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Neutral SW/ Clutch SW

        for Automatic Transmission:

      • Shift position (P and N)/ON or OFF


        for Manual Transmission:

      • State of clutch pedal/ON or OFF

        for Automatic Transmission:

      • ON: Shift lever in P or N

        OFF: Shift lever in any position other than P or N


        for Manual Transmission:

      • ON: Clutch pedal depressed

        OFF: Clutch pedal released

        for Automatic Transmission:

      • Use this item to determine whether the park/neutral position switch is malfunctioning.

      • When the engine cannot be started due to a park/neutral position switch malfunction, OFF is displayed.


        for Manual Transmission:

      • Use this item to help determine if the clutch position switch is malfunctioning .

      • The engine cannot be started when this item is "OFF".
      Starting Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Shift Position P or N Park/neutral position switch status/ON or OFF

      ON: Shift lever in P or N

      OFF: Shift lever in any position other than P or N

      		 When malfunctioning, the engine will not crank.
      OK
      The item in the Data List changes according to the shift position.
      Result
      Result Proceed to
      OK A
      NG for Automatic Transmission B
      for Manual Transmission C

    B

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    C

    INSPECT CLUTCH START SWITCH ASSEMBLY Click here

    A

  6. CHECK FOR DTC


    1. Using the GTS, check for DTCs.

      Result
      Result Proceed to
      DTCs are not output for Automatic Transmission A
      for Manual Transmission B
      Entry and start system (for Start Function) DTCs are output C

    B

    READ VALUE USING GTS (STARTER REQUEST SIGNAL) Click here

    C

    DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  7. READ VALUE USING GTS (STOP LIGHT SWITCH1)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. According to the display on the GTS, read the Data List.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Stop Light Switch1 State of brake pedal/ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      • Use this item to determine whether the stop light switch is malfunctioning.

      • The engine cannot be started when this item is OFF.

      • When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.
      OK
      The item in the Data List changes when the brake pedal is depressed and released.

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) Click here

    OK

  8. READ VALUE USING GTS (STARTER REQUEST SIGNAL)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. According to the display on the GTS, read the Data List.

      Power Source Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Starter Request Signal Engine start request signal status/ON or OFF

        for Automatic Transmission:

      • ON: With the shift lever in P and brake pedal depressed, the engine switch is pressed and held

        OFF: After approximately 1 second. has elapsed, the engine switch is released


        for Manual Transmission:

      • ON: With the clutch pedal depressed, the engine switch is pressed and held

        OFF: After approximately 1 second has elapsed, the engine switch is released

      • When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

      • When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain amount of time.

      Note

      Check that the key warning light is displayed on the multi-information display on the combination meter assembly, and then press the engine switch.

      OK
      The display changes in response to the operation of the engine switch.

    NG

    READ VALUE USING GTS (STARTER SW) Click here

    OK

  9. CHECK STEERING LOCK SYSTEM


    1. Check that the steering unlocks when the engine switch is turned on (ACC).

      OK
      The steering unlocks.

    NG

    GO TO STEERING LOCK SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

    OK

  10. CHECK SECURITY INDICATOR LIGHT (ENGINE IMMOBILISER SYSTEM UNSET)


    1. Get into the vehicle while carrying an electrical key transmitter sub-assembly.

    2. for Automatic Transmission:

      Move the shift lever to P.

    3. Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).


      • *1: for Automatic Transmission

      • *2: for Manual Transmission

      Tech Tips

      It is determined that the immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

      OK
      Security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    GO TO ENGINE IMMOBILISER SYSTEM (PROBLEM SYMPTOMS TABLE) Click here

  11. INSPECT TRANSMITTER BATTERY


    1. Inspect the transmitter battery.

      Note

      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.


    OK

    REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

    NG

    REPLACE TRANSMITTER BATTERY Click here

  12. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Remove the park/neutral position switch assembly.


    2. Inspect the park/neutral position switch assembly.


      Result
      Result Proceed to
      OK A
      NG for AB60F B
      for AE80F C
      for AC60F D

    B

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    C

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    D

    REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY Click here

    A

  13. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the C45*1 or C46*2 ECM connector.


      • *1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

    3. Disconnect the C24 park/neutral position switch assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 3UR-FE
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - C24-3 (B) Always Below 1 Ω
      E128-10 (STAR) or C24-3 (B) - Body ground 10 kΩ or higher
      except 3UR-FE
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - C24-4 (B) Always Below 1 Ω
      E128-10 (STAR) or C24-4 (B) - Body ground 10 kΩ or higher

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. INSPECT CLUTCH START SWITCH ASSEMBLY


    1. Remove the clutch start switch assembly.


    2. Inspect the clutch start switch assembly.


      Result
      Result Proceed to
      OK A
      NG for RHD B
      for LHD C

    B

    REPLACE CLUTCH SWITCH ASSEMBLY Click here

    C

    REPLACE CLUTCH SWITCH ASSEMBLY Click here

    A

  15. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the e1*1 or A49*2 clutch start switch assembly connector.


      • *1: for RHD

      • *2: for LHD

    3. Disconnect the C45*1 or C46*2 ECM connector.


      • *1: for 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1VD-FTV (for RHD)

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RHD:
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - e1-1 Always Below 1 Ω
      E128-10 (STAR) or e1-1 - Body ground 10 kΩ or higher
      for LHD:
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - A49-1 Always Below 1 Ω
      E128-10 (STAR) or A49-1 - Body ground 10 kΩ or higher

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  16. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the A38*1 or A52*2 ECM connector.


      • *1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

    2. Disconnect the A24 skid control ECU (brake actuator assembly) connector.

    3. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    4. Disconnect the A73 stop light switch assembly connector.

    5. Disconnect the E51 shift lock control ECU connector.

    6. Disconnect the A39 stop light control relay assembly connector.

    7. B001ZSEE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A73-1 (B) - Body ground Always 11 to 14 V

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E128-2 (STP1) - A73-2 (L) Always Below 1 Ω
      E128-2 (STP1) or A73-2 (L) - Body ground 10 kΩ or higher
      A73-3 (GND) - Body ground Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Inspect the stop light switch assembly Click here.


    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

  18. READ VALUE USING GTS (STARTER SW)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Starting Control / Data List.

    5. Get into the vehicle while carrying an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P and brake pedal depressed to check if the Data List display changes.

      Starting Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Starter SW Starter operation request/ON or OFF

      ON: Starter operation requested

      OFF: Starter operation not requested

      		 When malfunctioning, the engine will not crank.
      OK
      The Data List item changes.

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    OK

  19. INSPECT ST RELAY


    1. Remove the ST relay.

    2. Inspect the ST relay.



    NG

    REPLACE ST RELAY

    OK

  20. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BODY GROUND)


    1. B001WJQE01
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A38 and C45*1 or A52 and C46*2 ECM connector.


      • *1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

    3. for Automatic Transmission:

      Move the shift lever to P or N.

    4. for Manual Transmission:

      Depress the clutch pedal.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - Body ground 20°C (68°F) 93.75 to 136.36 Ω
      E128-12 (STA) - Body ground
      Result
      Result Proceed to
      OK A
      NG for Automatic Transmission B
      for Manual Transmission C

    B

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH) Click here

    C

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY) Click here

    A

  21. INSPECT STARTER ASSEMBLY


    1. Remove the starter assembly.


    2. Inspect the starter assembly .


      Result
      Result Proceed to
      OK A
      NG for 1UR-FE B
      for 1GR-FE C
      for 3UR-FE D
      for 1VD-FTV E

    B

    REPLACE STARTER ASSEMBLY Click here

    C

    REPLACE STARTER ASSEMBLY Click here

    D

    REPLACE STARTER ASSEMBLY Click here

    E

    REPLACE STARTER ASSEMBLY Click here

    A

  22. CHECK HARNESS AND CONNECTOR (BATTERY - STARTER AND ST RELAY )


    1. Remove the starter assembly from the vehicle to perform an inspection.


    2. Remove the ST relay.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for 3UR-FE
      Tester Connection Condition Specified Condition
      D16-1 - Body ground Always 11 to 14 V
      ST relay terminal 5 - Body ground
      for 1UR-FE
      Tester Connection Condition Specified Condition
      D21-1 - Body ground Always 11 to 14 V
      ST relay terminal 5 - Body ground
      for 1GR-FE
      Tester Connection Condition Specified Condition
      D20-1 - Body ground Always 11 to 14 V
      ST relay terminal 5 - Body ground
      for 1VD-FTV
      Tester Connection Condition Specified Condition
      D13-1 - Body ground Always 11 to 14 V
      ST relay terminal 5 - Body ground

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 1VD-FTV
      Tester Connection Condition Specified Condition
      ST relay terminal 3 - D12-1 Always Below 1 Ω
      ST relay terminal 3 or D12-1 - Body ground 10 kΩ or higher
      except 1VD-FTV
      Tester Connection Condition Specified Condition
      ST relay terminal 3 - D2-1 Always Below 1 Ω
      ST relay terminal 3 or D2-1 - Body ground 10 kΩ or higher

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  23. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the C24 park/neutral position switch connector.

    3. Disconnect the C45*1 or C46*2 ECM connector.


      • *1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 3UR-FE
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - C24-3 (B) Always Below 1 Ω
      E128-10 (STAR) or C24-3 (B) - Body ground 10 kΩ or higher
      except 3UR-FE
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - C24-4 (B) Always Below 1 Ω
      E128-10 (STAR) or C24-4 (B) - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  24. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    1. Disconnect the C24 park/neutral position switch connector.

    2. Remove the ST relay.

    3. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    4. Disconnect the A38*1 or A52*2 ECM connector.


      • *1: for 3UR-FE, 1UR-FE (for LHD), 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1UR-FE (for RHD) or 1VD-FTV (for RHD)

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 3UR-FE
      Tester Connection Condition Specified Condition
      C24-8 (L) - ST relay terminal 2 Always Below 1 Ω
      C24-8 (L) or ST relay terminal 2 - Body ground 10 kΩ or higher
      except 3UR-FE
      Tester Connection Condition Specified Condition
      C24-5 (L) - ST relay terminal 2 Always Below 1 Ω
      C24-5 (L) or ST relay terminal 2 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  25. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Remove the ST relay.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E128-12 (STA) - ST relay terminal 2 Always Below 1 Ω
      E128-12 (STA) or ST relay terminal 2 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  26. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    1. Remove the ST relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - Body ground Always Below 1 Ω

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  27. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the e1*1 or A49*2 clutch start switch assembly connector.


      • *1: for RHD

      • *2: for LHD

    3. Disconnect the C45*1 or C46*2 ECM connector.


      • *1: for 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1VD-FTV (for RHD)

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RHD:
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - e1-1 Always Below 1 Ω
      E128-10 (STAR) or e1-1 - Body ground 10 kΩ or higher
      for LHD:
      Tester Connection Condition Specified Condition
      E128-10 (STAR) - A49-1 Always Below 1 Ω
      E128-10 (STAR) or A49-1 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  28. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY)


    1. Disconnect the e1*1 or A49*2 clutch start switch assembly connector.


      • *1: for RHD

      • *2: for LHD

    2. Remove the ST relay.

    3. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    4. Disconnect the A38*1 or A52*2 ECM connector.


      • *1: for 1VD-FTV (for LHD) or 1GR-FE

      • *2: for 1VD-FTV (for RHD)

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RHD:
      Tester Connection Condition Specified Condition
      e1-2 - ST relay terminal 2 Always Below 1 Ω
      e1-2 or ST relay terminal 2 - Body ground 10 kΩ or higher
      for LHD:
      Tester Connection Condition Specified Condition
      A49-2 - ST relay terminal 2 Always Below 1 Ω
      A49-2 or ST relay terminal 2 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  29. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (CLUTCH START SWITCH ASSEMBLY - ST RELAY)


    1. Disconnect the E128 certification ECU (smart key ECU assembly) connector.

    2. Remove the ST relay.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E128-12 (STA) - ST relay terminal 2 Always Below 1 Ω
      E128-12 (STA) or ST relay terminal 2 - Body ground 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  30. CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    1. Remove the ST relay.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      ST relay terminal 1 - Body ground Always Below 1 Ω

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR