TELEMATICS SYSTEM(w/ Telematics Transceiver except G-BOOK), Diagnostic DTC:B1583

DTC Code DTC Name
B1583 GPS Signal Unreceived

DESCRIPTION

This DTC is stored when GNSS satellite signals is not received for 30 km.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1583 GPS Signal Unreceived GNSS signals are not received for 30 km.

  • Telematics transceiver

  • Telephone antenna assembly

  • No. 4 antenna cord sub-assembly

  • Antenna divider (for 14 Speakers)

  • Harness or connector

WIRING DIAGRAM

Figure 1. except 14 Speakers:

B001W6EE02

Figure 2. for 14 SPeakers:

B001VN2E01

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click here

PROCEDURE


  1. MOVE VEHICLE


    1. If the vehicle is outside the communication service area, move the vehicle into a communication service area, wait for a while and perform the operation again.

      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Turn the engine switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG) and wait for 20 seconds.

    4. Turn the GTS on.

    5. Check for DTCs and check that no DTCs are output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. CHECK OPTIONAL COMPONENTS


    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result
      Result Proceed to
      Optional components are not installed A
      Optional components are installed B

      Note

      Do not remove optional components without the permission of the customer.


    B

    REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

    A

  4. CHECK FOR DTC


    1. Clear the DTCs.

      Click here

    2. Check for DTCs and check if the same DTC is output again.

      Result
      Result Proceed to
      No DTCs are output. A
      DTC B1583 is output. B

    A

    END

    B

  5. CHECK VEHICLE CONDITION

    Result
    Result Proceed to
    except 14 Speakers A
    for 14 Speakers B

    1. Check the vehicle condition.

      Result
      Result Proceed to
      except 14 Speakers A
      for 14 Speakers B

    B

    INSPECT TELEPHONE ANTENNA ASSEMBLY Click here

    A

  6. INSPECT TELEPHONE ANTENNA ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Remove the telephone antenna assembly.

      Click here

    2. B001X7ZC17
      *a

      Component without harness connected

      (Telephone Antenna Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2a Always 4 to 11 kΩ
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEPHONE ANTENNA ASSEMBLY Click here

    OK

  7. INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. B001XG0C01
      *a

      Front view of wire harness connector

      (to Telephone Antenna Assembly)
      *b

      Front view of wire harness connector

      (to Wire Harness)

      Disconnect the antenna connector from the telephone antenna assembly.

    2. Disconnect the antenna connector from the wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - B-1 Always Below 1 Ω
      A-2 or B-1 - Body ground Always 10 kΩ or higher
      A-2a - B-1a Always Below 1 Ω
      A-2a or B-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (NO. 4 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER)

    Result
    Proceed to
    OK
    NG

    1. B002012C01
      *a

      Front view of wire harness connector

      (to No. 4 Antenna Cord Sub-assembly)
      *b

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.

    2. Disconnect the antenna connector from the telematics transceiver.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-1 - D-1 (ANT2) Always Below 1 Ω
      C-1 or D-1 (ANT2) - Body ground Always 10 kΩ or higher
      C-1a - D-1a Always Below 1 Ω
      C-1a or D-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. REPLACE TELEPHONE ANTENNA ASSEMBLY


    1. Replace the telephone antenna assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here

    3. Check for DTCs and check that no DTCs are output.

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

    NG

  10. REPLACE TELEMATICS TRANSCEIVER


    1. Replace the telematics transceiver with a new one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM REGISTRATION Click here

  11. INSPECT TELEPHONE ANTENNA ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. Remove the telephone antenna assembly.

      Click here

    2. B001X7ZC17
      *a

      Component without harness connected

      (Telephone Antenna Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 - 2a Always 4 to 11 kΩ
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TELEPHONE ANTENNA ASSEMBLY Click here

    OK

  12. INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

    Result
    Proceed to
    OK
    NG

    1. B002050C01
      *a

      Front view of wire harness connector

      (to Telephone Antenna Assembly)
      *b

      Front view of wire harness connector

      (to Wire Harness)

      Disconnect the antenna connector from the telephone antenna assembly.

    2. Disconnect the antenna connector from the wire harness.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-2 - B-1 Always Below 1 Ω
      A-2 or B-1 - Body ground Always 10 kΩ or higher
      A-2a - B-1a Always Below 1 Ω
      A-2a or B-1a - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY Click here

    OK

  13. INSPECT ANTENNA DIVIDER

    Result
    Proceed to
    OK
    NG

    1. B001XIZC03
      *a

      Front view of wire harness connector

      (to No. 4 Antenna Cord Sub-assembly)
      *a

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the antenna divider connector from the No. 4 antenna cord sub-assmbly.

    2. Disconnect the antenna divider connector from the telematics transceiver.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C-1 - D-1 (ANT2) Always Below 1 Ω
      C-1 - D-1a Always 10 kΩ or higher
      D-1 (ANT2) - D-1a Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 9 Click here

    NG

    REPLACE ANTENNA DIVIDER Click here