STEREO COMPONENT AMPLIFIER REMOVAL

PROCEDURE

1. PRECAUTION

   Note

   After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

   CAUTION:

   Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

   Note

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

3. REMOVE FRONT SEAT ASSEMBLY LH

   
   

   1. for Manual Seat:

      Remove the front seat assembly LH Click here.

   2. for Power Seat:

      Remove the front seat assembly LH Click here.

4. REMOVE FRONT SEAT ASSEMBLY RH

   
   

   1. for Manual Seat:

      Remove the front seat assembly RH Click here.

   2. for Power Seat:

      Remove the front seat assembly RH Click here.

      Tech Tips

      Use the same procedures described for the LH side.

5. REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER

   Click here

6. REMOVE REAR NO. 5 SEAT CUSHION HINGE COVER

   Click here

7. REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER

   Click here

8. REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER

   Click here

9. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

   Click here

10. REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER

    Click here

11. REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER

    Click here

12. REMOVE REAR NO. 1 SEAT CUSHION HINGE COVER

    Click here

13. REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER

    Click here

14. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

    Click here

15. REMOVE INSTRUMENT SIDE PANEL LH

    Click here

16. REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

    Click here

17. REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

    Click here

18. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

19. REMOVE FRONT DOOR SCUFF PLATE RH

    Click here

20. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    Click here

21. REMOVE COWL SIDE TRIM BOARD LH

    Click here

22. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    Click here

23. REMOVE COWL SIDE TRIM BOARD RH

    Click here

24. REMOVE REAR STEP COVER

    Click here

25. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

26. REMOVE REAR DOOR SCUFF PLATE RH

    Click here

27. REMOVE NO. 2 AIR DUCT PLUG

    
    

    1. 

       Detach the 4 claws and remove the 2 plugs.

       Tech Tips

       Use the same procedures for both sides.

28. REMOVE AIR HEATER GUIDE

    
    

    1. 

       Remove the 2 screws and guide.

       Tech Tips

       Use the same procedures for both sides.

29. REMOVE AIR DUCT PLUG

    
    

    1. 

       Detach the 2 claws and remove the plug.

       Tech Tips

       Use the same procedures for both sides.

30. REMOVE REAR AIR DUCT GUIDE

    
    

    1. 

       Remove the screw.

    2. Detach the claw and remove the guide.

       Tech Tips

       Use the same procedures for both sides.

31. REMOVE REAR NO. 1 SEAT PROTECTOR

    
    

    1. 

       Detach the clip and 4 claws, and remove the protector.

       Tech Tips

       Use the same procedures to remove the protector on the other side.

32. REMOVE REAR NO. 2 SEAT PROTECTOR

    
    

    1. 

       Detach the clip and 4 claws, and remove the protector.

       Tech Tips

       Use the same procedures to remove the protector on the other side.

33. REMOVE COOLING BOX ASSEMBLY (w/ Cool Box)

    
    

    1. Remove the cooling box assembly Click here.

34. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)

    
    

    1. Remove the rear console box sub-assembly Click here.

35. REMOVE FRONT FLOOR CARPET ASSEMBLY

    
    

    1. Detach the 2 clips and 8 claws.

       
    2. 

       Remove the carpet from the floor, open the back door and tail gate, and remove the carpet from the rear of the vehicle.

36. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

    
    

    1. 

       Disconnect the 3 connectors.

    2. Remove the 3 bolts and remove the amplifier with bracket.

37. REMOVE AMPLIFIER COVER

    
    

    1. 

       Detach the 3 clips and remove the cover.

38. REMOVE NO. 1 AMPLIFIER BRACKET

    

    
    

    1. Remove the 2 screws and bracket.

39. REMOVE NO. 2 AMPLIFIER BRACKET

    

    
    

    1. Remove the 2 screws and bracket.