AUDIO AND VISUAL SYSTEM(w/ Multi-display), Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

This DTC is stored from the multi-media module receiver assembly when a malfunction occurs in the speakers. In addition, the multi-media module receiver assembly detects a malfunction via the stereo component amplifier assembly.

DTC Code DTC Detection Condition Trouble Area
B15C3 A short is detected in the speaker output circuit.

  • Stereo component amplifier assembly

  • Speaker

  • DCM (telematics transceiver)*

  • Harness or connector

*: w/ Telematics Transceiver

WIRING DIAGRAM

B001VN8E07
B001X7SE02
B001YWSE04

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here

      Result
      Proceed
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Recheck for DTCs and check if the same DTC is output again.

      Click here

      OK
      DTC B15C3 is not output.
      Result
      Proceed
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. CONFIRM MODEL


    1. Choose the model to be inspected.

      Model
      Model Proceed to
      for 9 Speakers A
      for 14 Speakers B

    B

    CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT) Click here

    A

  4. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for RH Side

    • *2: for LH Side


    1. Disconnect the F74 stereo component amplifier assembly connector.

    2. Disconnect the I1*1 and/or I10*2 front No. 1 speaker assembly connector.

    3. Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.

    4. Disconnect the F13*1 and/or F14*2 front No. 3 speaker assembly connector.

    5. Disconnect the F6 front No. 4 speaker assembly connector.

    6. Disconnect the J18*1 and/or J19*2 rear speaker set connector.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH Side
      Tester Connection Condition Specified Condition
      F74-5 (WFR+) - I1-1 Always Below 1 Ω
      F74-20 (WFR-) - I1-2 Always Below 1 Ω
      F74-13 (FR+) - F7-1 (+) Always Below 1 Ω
      F74-28 (FR-) - F7-3 (-) Always Below 1 Ω
      F7-2 (TWR+) - F13-1 Always Below 1 Ω
      F7-4 (TWR-) - F13-2 Always Below 1 Ω
      F74-15 (RR+) - J18-1 Always Below 1 Ω
      F74-30 (RR-) - J18-2 Always Below 1 Ω
      F74-5 (WFR+) - Body ground Always 10 kΩ or higher
      F74-20 (WFR-) - Body ground Always 10 kΩ or higher
      F74-13 (FR+) - Body ground Always 10 kΩ or higher
      F74-28 (FR-) - Body ground Always 10 kΩ or higher
      F7-2 (TWR+) - Body ground Always 10 kΩ or higher
      F7-4 (TWR-) - Body ground Always 10 kΩ or higher
      F74-15 (RR+) - Body ground Always 10 kΩ or higher
      F74-30 (RR-) - Body ground Always 10 kΩ or higher
      for LH Side:
      Tester Connection Condition Specified Condition
      F74-4 (WFL+) - I10-1 Always Below 1 Ω
      F74-19 (WFL-) - I10-2 Always Below 1 Ω
      F74-12 (FL+) - F8-1 (+) Always Below 1 Ω
      F74-27 (FL-) - F8-3 (-) Always Below 1 Ω
      F8-2 (TWL+) - F14-1 Always Below 1 Ω
      F8-4 (TWL-) - F14-2 Always Below 1 Ω
      F74-14 (RL+) - J19-1 Always Below 1 Ω
      F74-29 (RL-) - J19-2 Always Below 1 Ω
      F74-4 (WFL+) - Body ground Always 10 kΩ or higher
      F74-19 (WFL-) - Body ground Always 10 kΩ or higher
      F74-12 (FL+) - Body ground Always 10 kΩ or higher
      F74-27 (FL-) - Body ground Always 10 kΩ or higher
      F8-2 (TWL+) - Body ground Always 10 kΩ or higher
      F8-4 (TWL-) - Body ground Always 10 kΩ or higher
      F74-14 (RL+) - Body ground Always 10 kΩ or higher
      F74-29 (RL-) - Body ground Always 10 kΩ or higher
      for Center Side:
      Tester Connection Condition Specified Condition
      F74-7 (CTR+) - F6-1 Always Below 1 Ω
      F74-22 (CTR-) - F6-2 Always Below 1 Ω
      F74-7 (CTR+) - Body ground Always 10 kΩ or higher
      F74-22 (CTR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  6. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  7. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    1. Remove the front No. 4 speaker assembly.

      Click here

    2. Inspect the front No. 4 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 4 SPEAKER ASSEMBLY Click here

    OK

  8. INSPECT REAR SPEAKER SET


    1. Remove the rear speaker set.

      Click here

    2. Inspect the rear speaker set.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER SET Click here

    OK

  9. CHECK FRONT NO. 3 SPEAKER ASSEMBLY


    1. Replace the front No. 3 speaker assembly with a new or known good one.

      Click here

    2. Check for DTCs and check if the same DTC is output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  10. CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)


    • *1: for RH Side

    • *2: for LH Side

    • *3: w/ Telematics Transceiver


    1. Disconnect the F74 stereo component amplifier assembly connector.

    2. Disconnect the I1*1 and/or I10*2 front No. 1 speaker assembly connector.

    3. Disconnect the F7*1 and/or F8*2 front No. 2 speaker assembly connector.

    4. Disconnect the F13*1 and/or F14*2 front No. 3 speaker assembly connector.

    5. Disconnect the F6 front No. 4 speaker assembly connector.

    6. Disconnect the P3 DCM (telematics transceiver) connector.*3

    7. Disconnect the S8*1 and/or S9*2 rear header speaker assembly connector.

    8. Disconnect the J2*1 and/or J9*2 rear No. 3 speaker connector.

    9. Disconnect the J18*1 and/or J19*2 rear speaker set connector.

    10. Disconnect the L4 No. 1 woofer box speaker assembly connector.

    11. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH Side (w/ Telematics Transceiver)
      Tester Connection Condition Specified Condition
      F74-5 (WFR+) - I1-1 Always Below 1 Ω
      F74-20 (WFR-) - I1-2 Always Below 1 Ω
      F74-13 (FR+) - P3-2 (SPI+) Always Below 1 Ω
      F74-28 (FR-) - P3-3 (SPI-) Always Below 1 Ω
      P3-5 (SPO+) - F7-1 (+) Always Below 1 Ω
      P3-6 (SPO-) - F7-3 (-) Always Below 1 Ω
      F7-2 (TWR+) - F13-1 Always Below 1 Ω
      F7-4 (TWR-) - F13-2 Always Below 1 Ω
      F74-11 (SR+) - S8-1 (RRD+) Always Below 1 Ω
      F74-26 (SR-) - S8-2 (RRD-) Always Below 1 Ω
      F74-15 (R-R+) - J2-1 (+) Always Below 1 Ω
      F74-30 (R-R-) - J2-3 (-) Always Below 1 Ω
      J2-2 (+) - J18-1 (WF+) Always Below 1 Ω
      J2-4 (-) - J18-2 (WF-) Always Below 1 Ω
      F74-5 (WFR+) - Body ground Always 10 kΩ or higher
      F74-20 (WFR-) - Body ground Always 10 kΩ or higher
      F74-13 (FR+) - Body ground Always 10 kΩ or higher
      F74-28 (FR-) - Body ground Always 10 kΩ or higher
      P3-5 (SPO+) - Body ground Always 10 kΩ or higher
      P3-6 (SPO-) - Body ground Always 10 kΩ or higher
      F7-2 (TWR+) - Body ground Always 10 kΩ or higher
      F7-4 (TWR-) - Body ground Always 10 kΩ or higher
      F74-11 (SR+) - Body ground Always 10 kΩ or higher
      F74-26 (SR-) - Body ground Always 10 kΩ or higher
      F74-15 (R-R+) - Body ground Always 10 kΩ or higher
      F74-30 (R-R-) - Body ground Always 10 kΩ or higher
      J2-2 (+) - Body ground Always 10 kΩ or higher
      J2-4 (-) - Body ground Always 10 kΩ or higher
      for RH Side (w/o Telematics Transceiver):
      Tester Connection Condition Specified Condition
      F74-5 (WFR+) - I1-1 Always Below 1 Ω
      F74-20 (WFR-) - I1-2 Always Below 1 Ω
      F74-13 (FR+) - F7-1 (+) Always Below 1 Ω
      F74-28 (FR-) - F7-3 (-) Always Below 1 Ω
      F7-2 (TWR+) - F13-1 Always Below 1 Ω
      F7-4 (TWR-) - F13-2 Always Below 1 Ω
      F74-11 (SR+) - S8-1 (RRD+) Always Below 1 Ω
      F74-26 (SR-) - S8-2 (RRD-) Always Below 1 Ω
      F74-15 (R-R+) - J2-1 (+) Always Below 1 Ω
      F74-30 (R-R-) - J2-3 (-) Always Below 1 Ω
      J2-2 (+) - J18-1 (WF+) Always Below 1 Ω
      J2-4 (-) - J18-2 (WF-) Always Below 1 Ω
      F74-5 (WFR+) - Body ground Always 10 kΩ or higher
      F74-20 (WFR-) - Body ground Always 10 kΩ or higher
      F74-13 (FR+) - Body ground Always 10 kΩ or higher
      F74-28 (FR-) - Body ground Always 10 kΩ or higher
      F7-2 (TWR+) - Body ground Always 10 kΩ or higher
      F7-4 (TWR-) - Body ground Always 10 kΩ or higher
      F74-11 (SR+) - Body ground Always 10 kΩ or higher
      F74-26 (SR-) - Body ground Always 10 kΩ or higher
      F74-15 (R-R+) - Body ground Always 10 kΩ or higher
      F74-30 (R-R-) - Body ground Always 10 kΩ or higher
      J2-2 (+) - Body ground Always 10 kΩ or higher
      J2-4 (-) - Body ground Always 10 kΩ or higher
      for LH Side:
      Tester Connection Condition Specified Condition
      F74-4 (WFL+) - I10-1 Always Below 1 Ω
      F74-19 (WFL-) - I10-2 Always Below 1 Ω
      F74-12 (FL+) - F8-1 (+) Always Below 1 Ω
      F74-27 (FL-) - F8-3 (-) Always Below 1 Ω
      F8-2 (TWL+) - F14-1 Always Below 1 Ω
      F8-4 (TWL-) - F14-2 Always Below 1 Ω
      F74-10 (SL+) - S9-1 (RLD+) Always Below 1 Ω
      F74-25 (SL-) - S9-2 (RLD-) Always Below 1 Ω
      F74-14 (R-L+) - J9-1 (+) Always Below 1 Ω
      F74-29 (RL-) - J9-3 (-) Always Below 1 Ω
      J9-2 (+) - J19-1 (WF+) Always Below 1 Ω
      J9-4 (-) - J19-2 (WF-) Always Below 1 Ω
      F74-4 (WFL+) - Body ground Always 10 kΩ or higher
      F74-19 (WFL-) - Body ground Always 10 kΩ or higher
      F74-12 (FL+) - Body ground Always 10 kΩ or higher
      F74-27 (FL-) - Body ground Always 10 kΩ or higher
      F8-2 (TWL+) - Body ground Always 10 kΩ or higher
      F8-4 (TWL-) - Body ground Always 10 kΩ or higher
      F74-10 (SL+) - Body ground Always 10 kΩ or higher
      F74-25 (SL-) - Body ground Always 10 kΩ or higher
      F74-14 (R-L+) - Body ground Always 10 kΩ or higher
      F74-29 (RL-) - Body ground Always 10 kΩ or higher
      J9-2 (+) - Body ground Always 10 kΩ or higher
      J9-4 (-) - Body ground Always 10 kΩ or higher
      for Center Side:
      Tester Connection Condition Specified Condition
      F74-7 (CTR+) - F6-1 Always Below 1 Ω
      F74-22 (CTR-) - F6-2 Always Below 1 Ω
      F74-6 (WF1+) - L4-1 (WF1+) Always Below 1 Ω
      F74-21 (WF1-) - L4-2 (WF1-) Always Below 1 Ω
      F74-8 (WF2+) - L4-3 (WF2+) Always Below 1 Ω
      F74-23 (WF2-) - L4-4 (WF2-) Always Below 1 Ω
      F74-7 (CTR+) - Body ground Always 10 kΩ or higher
      F74-22 (CTR-) - Body ground Always 10 kΩ or higher
      F74-6 (WF1+) - Body ground Always 10 kΩ or higher
      F74-21 (WF1-) - Body ground Always 10 kΩ or higher
      F74-8 (WF2+) - Body ground Always 10 kΩ or higher
      F74-23 (WF2-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  12. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  13. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY


    1. Remove the front No. 4 speaker assembly.

      Click here

    2. Inspect the front No. 4 speaker assembly.

      Click here

      Result
      Result
      OK
      NG

    NG

    REPLACE FRONT NO. 4 SPEAKER ASSEMBLY Click here

    OK

  14. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

      Result
      Proceed
      OK
      NG

    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

    OK

  15. INSPECT REAR SPEAKER SET


    1. Remove the rear speaker set.

      Click here

    2. Inspect the rear speaker set.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR SPEAKER SET Click here

    OK

  16. INSPECT NO. 1 WOOFER BOX SPEAKER ASSEMBLY


    1. Remove the No. 1 woofer box speaker assembly.

      Click here

    2. Inspect the No. 1 woofer box speaker assembly.

      Click here

      Result
      Proceed
      OK
      NG

    NG

    REPLACE NO. 1 WOOFER BOX SPEAKER ASSEMBLY Click here

    OK

  17. CHECK FRONT NO. 3 SPEAKER ASSEMBLY


    1. Replace the front No. 3 speaker assembly with a new or known good one.

      Click here

    2. Check for DTCs and check if the same DTC is output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG

  18. CHECK REAR NO. 3 SPEAKER ASSEMBLY


    1. Replace the rear No. 3 speaker assembly with a new or known good one.

      Click here

    2. Check for DTCs and check if the same DTC is output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG (w/Telematics Transceiver)
      NG (w/o Telematics Transceiver)

    OK

    END (REAR NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

    NG (w/o Telematics Transceiver)

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

    NG (w/Telematics Transceiver)

  19. CHECK DCM (TELEMATICS TRANSCEIVER)


    1. Replace the DCM (telematics transceiver) with a new one.

      Click here

    2. Check for DTCs and check if the same DTC is output.

      Click here

      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (DCM [TELEMATICS TRANSCEIVER] IS DEFECTIVE)

    NG

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here