AUDIO AND VISUAL SYSTEM(w/o Navigation System) Illumination Circuit

CAUTION / NOTICE / HINT

DESCRIPTION

Power is supplied to the radio receiver and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A01X3BFE02

CAUTION / NOTICE / HINT

CAUTION:


  • The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution for the SRS Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the multi-display, steering pad switch, glove box light, cigarette lighter, or others (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch. A
      Illumination comes on for all components except radio receiver. B
      No illumination comes on for radio receiver, multi-display, glove box light, front seat memory switch, cigarette lighter, etc. C

    B

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MAIN BODY ECU) Click here

    C

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

    A01X4V6E01
    Text in Illustration
    *1

    Front view of wire harness connector

    (to Spiral Cable)

    1. Disconnect the E12 cable connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E12-12 (IL+2) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT STEERING PAD SWITCH ASSEMBLY (STEERING PAD SIDE)

    A01X4FME04

    1. Disconnect the z36 switch connector.

    2. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 5 (IL+2)

      Battery negative (-) → Terminal 8 (EAU)

      		 Light illuminates

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  4. INSPECT SPIRAL CABLE SUB-ASSEMBLE

    A01X87YE02
    Text in Illustration
    *1 Vehicle Side *2 Steering Pad Switch Side

    1. Remove the spiral cable Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E12-12 (IL+2) - z36-5 (IL+2) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
      Spiral cable is centered
      Spiral cable is turned 2.5 rotations clockwise
      E12-4 (EAU) - z36-8 (EAU) Spiral cable is turned 2.5 rotations counterclockwise Below 1 Ω
      Spiral cable is centered
      Spiral cable is turned 2.5 rotations clockwise

      CAUTION:

      The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the SRS Click here.


    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


    1. Disconnect the F19 radio receiver connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F19-6 (SWG) - E12-4 (EAU) Always Below 1 Ω
      F19-6 (SWG) - Body ground Always 10 kΩ or higher

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - MAIN BODY ECU)


    1. Disconnect the F19 receiver connector.

    2. Disconnect the E2 main body ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F19-20 (ADIM) - E2-16 (ACAN) Always Below 1 Ω
      F19-20 (ADIM) - Body ground Always 10 kΩ or higher

    OK

    REPLACE RADIO RECEIVER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR