AUDIO AND VISUAL SYSTEM(for Radio and Display Type) DTC CHECK / CLEAR


  1. CHECK DTC (CHECK USING GTS)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

    5. Check for DTCs, and then write them down.

    6. Check the details of the DTC(s).

  2. CLEAR DTC (CLEAR USING GTS)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Navigation System / Trouble Codes.

    5. Clear the DTCs.

  3. START DIAGNOSTIC MODE

    Tech Tips


    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    • After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.


    1. Method 1


      1. Start the engine.

      2. B001XF4E01
        Text in Illustration
        *a AUDIO Switch

        While pressing and holding the "AUDIO" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

      3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

    2. Method 2


      1. Start the engine.

      2. Turn the radio and display receiver assembly power supply off.

      3. B001ZHWE01
        Text in Illustration
        *a SEEK Switch
        *b TRACK Switch

        Press the "SEEK" switch 5 times, and then press the "TRACK" switch 5 times within 15 seconds.

      4. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  4. FAILURE DIAGNOSIS


    1. B001XOK

      The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.

  5. SYSTEM CHECK


    1. B002056

      The "System Check Mode" screen will be displayed by selecting "System Check" on the "Failure Diagnosis" screen.

  6. CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)


    1. B001X8OE01

      System check mode screen description

      Screen Description
      Display Content
      *a: Device Name List No. 1

      • Device Name List No. 1 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 1 are shown in the following table.
      *b: Check Result Result codes for all devices are displayed.
      *c: Memory Clear

      • Present and history DTCs and registered connected device names are cleared.

      • Select "Memory CLR" for 3 seconds.
      *d: Recheck

      • A system check will be performed again after the memory is cleared.

      • "Recheck" will dim during a system check.
      *e: Device Name List No. 2

      • Device Name List No. 2 displays some of the devices that make up the audio and visual system.

      • The names of the components from Device Name List No. 2 are shown in the following table.
      *b: Device Name List No. 1 Description
      Name Component Connection Method
      DA Radio and display receiver assembly -
      *c: Check Result Description
      Result Meaning Action
      OK The device does not respond with a DTC. -
      DETAIL The device responds with a DTC. Look up the DTC in "Unit Check Mode".
      NCON The device was previously present, but does not respond in diagnostic mode. Check power supply wire harness of the device.
      NRES The device responds in diagnostic mode, but gives no DTC information. Check power supply wire harness of the device.
      *e: Device Name List No. 2 Description
      Name Component Connection Method
      AUX/VTR No. 1 stereo jack adapter assembly Vehicle wire harness
      VTR/RR No. 1 stereo jack adapter assembly Vehicle wire harness
    2. B00206LE02

      Unit check mode screen description

      Screen Description
      Display Content
      *a: Device name Target device
      *b: History DTC Diagnostic memory results and stored DTCs are displayed.
      *c: Current DTC DTCs output in the service check are displayed.
      *d: DTC Diagnostic Trouble Code (DTC)
      *e: Timestamp The time and date of history DTCs are displayed. (The year is displayed in 2- digit format.)
      *f: Diagnosis clear switch Selecting "Code CLR" for 3 seconds clears the diagnostic memory data of the target device. (Both diagnostic system check result and the displayed data are cleared.)

      Tech Tips


      • This screen is updated once per second.

      • A maximum of 6 DTCs can be displayed for history and present DTCs.

    3. B001ZT4

      Read the system check result.


      1. If the check result is "DETAIL", select the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Note

        A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit Check Mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit Check Mode" screen again to see if any other DTCs are displayed.

        Tech Tips


        • When all results are "OK", no DTCs are output.

        • When proceeding to view the results of another device, select the "Back" switch to return to the "System Check Mode" screen. Repeat the above step to view the results of other devices.

  7. DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)


    1. B001Y1T

      Clear DTCs


      1. Select "Memory CLR" for 3 seconds.

      2. Confirm that the check results are cleared.

        Tech Tips


        • To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.

        • When clearing DTCs using the "Unit Check Mode" screen, select "Code CLR" for 3 seconds.

    2. B001VYK

      Recheck


      1. Press the "Recheck" switch.

      2. B001W0E

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a result other than "OK" is displayed, perform troubleshooting again.

        Tech Tips

        When the DTCs are cleared using the "Unit Check Mode" screen, select "Back" to return to the "System Check Mode" screen and perform this operation.

  8. FINISH DIAGNOSTIC MODE


    1. There are 2 methods to end diagnostic mode. Use one of them.

    2. Turn the engine switch off.

    3. Press and hold the "SET UP" or "MENU" switch for 3 seconds.