STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT


    1. B00204IE02
      Text in Illustration
      *a Matchmark

      Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

      Note

      Be careful not to damage the dust cover.

  2. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY (w/ VGRS)


    1. Install the 4 bolts and nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Note

      Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.

  3. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY (w/o VGRS)


    1. Install the 4 bolts and nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Note

      Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.

      Tech Tips

      Install the steering intermediate shaft assembly from the inside of the vehicle.

    2. Install the clamp to the steering column hole cover.

  4. CONNECT STEERING ACTUATOR ASSEMBLY

    Click here

  5. INSTALL STEERING COLUMN ASSEMBLY


    1. Install the 4 nuts and steering column.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

    2. w/ VGRS:


      1. B001VX7E02
        Text in Illustration
        *a Matchmark

        Align the matchmarks on the steering column and steering actuator assembly.

      2. Install the bolt.

        Torque:
        35 N*m  { 357 kgf*cm, 26 ft.*lbf }

    3. w/o VGRS:


      1. B001X9CE03
        Text in Illustration
        *a Matchmark

        Align the matchmarks on the steering column and steering intermediate shaft.

      2. Install the bolt.

        Torque:
        35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  6. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

    Click here

  7. INSTALL WIRE HARNESS PROTECTOR AND WIRE HARNESS


    1. Attach the 2 claws and 2 harness clamps and connect the wire harness protector and wire harness.

  8. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  9. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    Click here

  10. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Attach the 3 claws to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.

    2. Connect connectors to the combination switch assembly with spiral cable sub-assembly.

  11. INSTALL UPPER STEERING COLUMN COVER


    1. Attach the 2 guide pin and claw.

    2. Attach the 4 clips and 2 claws to install the upper steering column cover onto the meter hood spacer.

  12. INSTALL LOWER STEERING COLUMN COVER


    1. Attach the 4 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  13. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  14. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

  15. INSTALL FRONT WHEEL

  16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSPECT SRS WARNING LIGHT

    Click here

  18. PERFORM VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION (w/ VGRS)

    Click here