STEERING ACTUATOR REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column Click here.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disable the AUTO TILT AWAY function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the current setting after finishing the operation.

      Tech Tips

      Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.

    2. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE LOWER NO. 3 STEERING WHEEL COVER

    Click here

  4. REMOVE LOWER NO. 2 STEERING WHEEL COVER

    Click here

  5. REMOVE STEERING PAD

    Click here

  6. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  7. REMOVE LOWER STEERING COLUMN COVER

    A01X228

    1. Remove the 3 screws.

    2. Detach the 2 claws to remove the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

  8. REMOVE UPPER STEERING COLUMN COVER

    A01X6NQ

    1. Detach the 4 clips.

    2. Detach the claw to remove the upper steering column cover.

  9. REMOVE TILT AND TELESCOPIC SWITCH

    A01X1XW

    1. Disconnect the switch connector.

    2. Using a screwdriver, detach the claw and pull out the switch.

      Tech Tips

      Tape the screwdriver tip before use.

      Note

      Pushing on the claw too hard will break the claw.

  10. REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    A01XB0R

    1. Disconnect the 5 connectors from the combination switch with spiral cable.

    2. A01X2DL

      Using pliers, grip the claws of the clamp and remove the combination switch with spiral cable from the steering column.

  11. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

    Click here

  12. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

    Click here

  13. REMOVE INSTRUMENT SIDE PANEL LH

    Click here

  14. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    Click here

  15. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    Click here

  16. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

    Click here

  17. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

    Click here

  18. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  19. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    Click here

  20. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  21. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  22. REMOVE NO. 1 SWITCH HOLE BASE

    Click here

  23. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    Click here

  24. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    Click here

  25. DISCONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS

    A01X35M

    1. Detach the 3 claws to disconnect the wire harness protector and wire harness.

  26. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

    Click here

  27. REMOVE STEERING COLUMN ASSEMBLY

    B001VX7E01
    *1 Matchmark

    1. Put matchmarks on the steering actuator and steering column.

    2. Remove the bolt.

    3. A01XAGF

      Remove the 4 nuts and steering column.

  28. REMOVE STEERING ACTUATOR ASSEMBLY

    B001ZJY

    1. While pushing the claws on both sides of the connector, move the lock in the direction of the arrow.

    2. Disconnect the connector.

    3. B001YQI

      Hold the clamp with needle nose pliers, then insert a screwdriver and turn it in the direction shown in the illustration to remove the clamp of the steering column hole cover.

    4. B001X2QE06
      *1 Matchmark

      Put matchmarks on the steering actuator and No. 2 steering intermediate shaft.

    5. Remove the bolt, and then pull out the actuator assembly toward the inside of the vehicle.