FRONT SPEED SENSOR INSTALLATION

PROCEDURE


  1. INSTALL FRONT SPEED SENSOR LH


    1. B001Z4J

      Install the speed sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

      • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • Make sure there is no foreign matter attached to the speed sensor rotor.

  2. INSTALL FRONT SKID CONTROL SENSOR WIRE LH


    1. w/o AHC:


      1. B001X2C

        Connect the connector.

      2. Install the harness clamp with the bolt.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamp, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

    2. w/ AHC:


      1. B001WRC

        Connect the 2 connectors.

      2. Install the harness clamp with the bolt.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamp, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

    3. B001Y7M

      Install the 2 harness clamps with the 2 bolts.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamps, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    4. B001Y7Y

      Install the harness clamp with the nut.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    5. B001XIBE01
      *1 Stopper

      Install the harness clamp with bolt

      Torque:
      except China
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }
      for China
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note

      Install the bracket so that the rotation stopper touches the knuckle.

    6. Connect the speed sensor connector.

      Note

      Securely connect the connector.

  3. INSTALL FRONT SPEED SENSOR RH


    1. B001Z2N

      Install the speed sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip part.

      • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • Make sure there is no foreign matter attached to the speed sensor rotor.

  4. INSTALL FRONT SKID CONTROL SENSOR WIRE RH


    1. w/o AHC:


      1. B001WUEE01

        Install the skid control sensor clamp with the bolt (labeled A).

        Torque:
        for bolt A
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      2. Attach the connector to the skid control sensor clamp and then connect the connector.

      3. Install the 2 harness clamps with the 2 bolts.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamps, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

    2. w/ AHC:


      1. B00201QE01

        Install the skid control sensor clamp with the bolt (labeled A).

        Torque:
        for bolt A
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      2. Attach the connector to the skid control sensor clamp and then connect the connector.

      3. Install the 2 harness clamps with the 2 bolts.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

        Note


        • When installing the clamps, do not twist the wire harness.

        • Make sure the clamp rotation stopper touches the installation position.

      4. B001Z9F

        Install the harness clamp with the bolt.

        Torque:
        13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      5. Connect the connector.

    3. B001Z9R

      Install the harness clamp with the nut.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    4. B001X51E01
      *1 Stopper

      Install the harness clamp with bolt.

      Torque:
      except China
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }
      for China
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

      Note

      Install the bracket so that the rotation stopper touches the knuckle.

    5. Connect the speed sensor connector.

      Note

      Securely connect the connector.

  5. INSTALL FRONT WHEEL

    Torque:
    for Aluminum Wheel
    131 N*m  { 1336 kgf*cm, 97 ft.*lbf }
    for Steel Wheel
    209 N*m  { 2131 kgf*cm, 154 ft.*lbf }

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. CHECK SPEED SENSOR SIGNAL


    1. w/ ABS:

      Check the speed sensor signal Click here.

    2. w/ VSC:

      Check the speed sensor signal Click here.