OUTPUT SHAFT REASSEMBLY

PROCEDURE


  1. INSTALL NO. 2 TRANSMISSION HUB SLEEVE

    A01X307E01
    *1 Front Side

    1. Apply a light coat of gear oil to the No. 2 transmission hub sleeve and No. 2 transmission clutch hub.

    2. Install the No. 2 transmission hub sleeve and 3 shifting keys to the No. 2 transmission clutch hub.

      Note

      Do not mistake the installation direction of the No. 2 transmission hub sleeve and No. 2 transmission clutch hub.

    3. A01WZS1

      Insert the 2 springs under the shifting keys.

      Note

      Position the key springs so that their end gaps are not aligned.

  2. INSTALL NO. 3 TRANSMISSION HUB SLEEVE

    A01X9U7E01
    *1 Front Side

    1. Apply a light coat of gear oil to the No. 3 transmission hub sleeve and No. 3 transmission clutch hub.

    2. Install the No. 3 transmission hub sleeve and 3 shifting keys to the No. 3 transmission clutch hub.

      Note

      Do not mistake the installation direction of the No. 3 transmission hub sleeve, No. 3 transmission clutch hub, and shifting keys.

    3. A01WZS1

      Insert the 2 springs under the shifting keys.

      Note

      Position the key springs so that their end gaps are not aligned.

  3. INSTALL NO. 1 TRANSMISSION HUB SLEEVE

    A01WZ31E01
    *1 Front Side

    1. Apply a light coat of gear oil to the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.

    2. Install the No. 1 transmission hub sleeve and 3 shifting keys to the No. 1 transmission clutch hub.

      Note

      Do not mistake the installation direction of the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.

    3. A01WZS1

      Insert the 2 springs under the shifting keys.

      Note

      Position the key springs so that their end gaps are not aligned.

  4. INSTALL 5TH COUNTER GEAR BEARING

    A01X5U3

    1. Coat the 5th counter gear bearing with gear oil, then install it to the 5th gear.

  5. INSTALL 5TH GEAR


    1. Coat the 5th gear and No. 3 synchronizer ring with gear oil, and set them onto the output shaft.

    2. A01X6N0E01

      Using SST and a press, install the 5th gear, No. 3 synchronizer ring and transmission hub sleeve to the output shaft.

      SST
      09316-60011   ( 09316-00011 )

      Tech Tips

      Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.

    3. Check that the 5th gear, No. 3 synchronizer ring, and transmission hub sleeve move smoothly.

  6. INSTALL NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

    A01X8CH

    1. Select a new snap ring that will allow minimum clearance.

      Standard Clearance
      0.1 mm (0.00393 in.) or less
      Snap Ring Thickness
      Part No. Thickness Mark
      90520-34018

      2.40 to 2.45 mm

      (0.0945 to 0.0965 in.)

      		 A
      90520-34019

      2.45 to 2.50 mm

      (0.0965 to 0.0984 in.)

      		 B
      90520-34020

      2.50 to 2.55 mm

      (0.0984 to 0.100 in.)

      		 C
      90520-34021

      2.55 to 2.60 mm

      (0.100 to 0.102 in.)

      		 D
      90520-34022

      2.60 to 2.65 mm

      (0.102 to 0.104 in.)

      		 E
      90520-34023

      2.65 to 2.70 mm

      (0.104 to 0.106 in.)

      		 F
    2. A01X89I

      Using a brass bar and hammer, install the snap ring to the output shaft.

  7. INSTALL 3RD GEAR NEEDLE ROLLER BEARING

    A01X7AX

    1. Coat the 3rd gear needle roller bearing with gear oil, and install it to the 3rd gear.

  8. INSTALL 3RD GEAR


    1. Coat the 3rd gear and No. 3 synchronizer ring set with gear oil, and set them onto the output shaft.

      Tech Tips

      Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.

    2. A01X0B2E01

      Using SST and a press, install the 3rd gear, No. 3 synchronizer ring set and transmission hub sleeve to the output shaft.

      SST
      09316-60011   ( 09316-00011 )

      Tech Tips

      Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.

    3. Check that the 3rd gear, No. 3 synchronizer ring set, and transmission hub sleeve move smoothly.

  9. INSTALL NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

    A01X9YE

    1. Select a new snap ring that will allow minimum clearance.

      Standard Clearance
      0.1 mm (0.00393 in.) or less
      Snap Ring Thickness
      Part No. Thickness Mark
      90520-28054

      1.90 to 1.95 mm

      (0.0748 to 0.0768 in.)

      		 4
      90520-28055

      1.95 to 2.00 mm

      (0.0768 to 0.0787 in.)

      		 5
      90520-28056

      2.00 to 2.05 mm

      (0.0787 to 0.0807 in.)

      		 6
      90520-28057

      2.05 to 2.10 mm

      (0.0807 to 0.0827 in.)

      		 7
      90520-28058

      2.10 to 2.15 mm

      (0.0827 to 0.0847 in.)

      		 8
      90520-28059

      2.15 to 2.20 mm

      (0.0847 to 0.0866 in.)

      		 9
    2. A01X66I

      Using a snap ring expander, install the snap ring to the output shaft.

  10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING

    A01X139

    1. Coat the 2nd gear needle roller bearing with gear oil, and install it to the output shaft.

  11. INSTALL 2ND GEAR


    1. Coat the 2nd gear and No. 2 synchronizer ring set with gear oil, then install them to the output shaft.

      Tech Tips

      Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.

    2. A01X0DV

      Using a press, install the 2nd gear, No. 2 synchronizer ring set and transmission hub sleeve to the output shaft.

      Tech Tips

      Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.

    3. Check that the 2nd gear, No. 2 synchronizer ring set, and transmission hub sleeve move smoothly.

  12. INSTALL NO. 1 CLUTCH HUB SHAFT SNAP RING

    A01X7M7

    1. Select a new snap ring that will allow minimum clearance.

      Standard Clearance
      0.1 mm (0.00393 in.) or less
      Snap Ring Thickness
      Part No. Thickness Mark
      90520-46004

      2.90 to 2.95 mm

      (0.114 to 0.116 in.)

      		 A
      90520-46005

      2.95 to 3.00 mm

      (0.116 to 0.118 in.)

      		 B
      90520-46006

      3.00 to 3.05 mm

      (0.118 to 0.120 in.)

      		 C
      90520-46007

      3.05 to 3.10 mm

      (0.120 to 0.122 in.)

      		 D
      90520-46008

      3.10 to 3.15 mm

      (0.122 to 0.124 in.)

      		 E
      90520-46009

      3.15 to 3.20 mm

      (0.124 to 0.126 in.)

      		 F
    2. A01WYXR

      Using a brass bar and a hammer, install the snap ring to the output shaft.

  13. INSTALL 1ST GEAR NEEDLE ROLLER BEARING

    A01X5G9

    1. Coat the 1st gear needle roller bearing with gear oil, and install it to the output shaft.

  14. INSTALL 1ST GEAR


    1. Coat the 1st gear and No. 1 synchronizer ring set with gear oil, and set them onto the output shaft.

      Tech Tips

      Align the protrusions of the middle ring of the synchronizer ring set with the notches of the gear.

    2. A01X44FE01

      Using SST and press, install the 1st gear, No. 1 synchronizer ring set, and output shaft rear bearing to the output shaft.

      SST
      09316-60011   ( 09316-00011 )
      09523-36010

      Tech Tips


      • Make sure that the groove of the bearing faces the correct direction as shown in the illustration.

      • Align the convex portion of the synchronizer ring with the groove of the transmission hub sleeve.

    3. Check that the transmission hub sleeve, 1st gear and No. 1 synchronizer ring set move smoothly.

  15. INSTALL REVERSE GEAR SNAP RING

    A01X8HY

    1. Select a new snap ring that will allow minimum clearance.

      Standard Clearance
      0.1 mm (0.00393 in.) or less
      Snap Ring Thickness
      Part No. Thickness Mark
      90520-41006

      2.40 to 2.45 mm

      (0.0945 to 0.0965 in.)

      		 A
      90520-41007

      2.45 to 2.50 mm

      (0.0965 to 0.0984 in.)

      		 B
      90520-41008

      2.50 to 2.55 mm

      (0.0984 to 0.100 in.)

      		 C
      90520-41009

      2.55 to 2.60 mm

      (0.100 to 0.102 in.)

      		 D
      90520-41010

      2.60 to 2.65 mm

      (0.102 to 0.104 in.)

      		 E
      90520-41011

      2.65 to 2.70 mm

      (0.104 to 0.106 in.)

      		 F
      90520-41012

      2.70 to 2.75 mm

      (0.106 to 0.108 in.)

      		 G
      90520-41013

      2.75 to 2.80 mm

      (0.108 to 0.110 in.)

      		 H
    2. A01X12I

      Using a brass bar and a hammer, install the snap ring to the output shaft.

  16. INSPECT 5TH GEAR THRUST CLEARANCE

    A01WZKEE07
    *a 5th Gear Thrust Clearance

    1. Using a feeler gauge, measure the 5th gear thrust clearance.

      Standard Clearance
      0.10 to 0.35 mm (0.00394 to 0.0137 in.)

      If the clearance is outside the specification, replace the defective gear or shaft.

  17. INSPECT 3RD GEAR THRUST CLEARANCE

    A01WZKEE01
    *a 3rd Gear Thrust Clearance

    1. Using a feeler gauge, measure the 3rd gear thrust clearance.

      Standard Clearance
      0.10 to 0.45 mm (0.00394 to 0.0177 in.)

      If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.

  18. INSPECT 2ND GEAR THRUST CLEARANCE

    A01WZKEE04
    *a 2nd Gear Thrust Clearance

    1. Using a feeler gauge, measure the 2nd gear thrust clearance.

      Standard Clearance
      0.10 to 0.35 mm (0.00394 to 0.0137 in.)

      If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.

  19. INSPECT 1ST GEAR THRUST CLEARANCE

    A01WZKEE06
    *a 1st Gear Thrust Clearance

    1. Using a feeler gauge, measure the 1st gear thrust clearance.

      Standard Clearance
      0.10 to 0.45 mm (0.00394 to 0.0177 in.)

      If the clearance is outside the specification, replace the defective gear, transmission clutch hub or shaft.

  20. INSPECT 5TH GEAR RADIAL CLEARANCE

    Click here

  21. INSPECT 3RD GEAR RADIAL CLEARANCE

    Click here

  22. INSPECT 2ND GEAR RADIAL CLEARANCE

    Click here

  23. INSPECT 1ST GEAR RADIAL CLEARANCE

    Click here