OIL COOLER INSTALLATION

PROCEDURE


  1. INSTALL OIL COOLER ASSEMBLY

    B001ZSQE01

    1. Install the oil cooler inlet hose and oil cooler outlet hose, connect the air cooled oil cooler tube, and slide the 4 hose clips to secure the hose.

      Text in Illustration
      *a Lower Side
      *b Outward
    2. B001VPV

      Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the rear transmission oil cooler air duct with the bolt.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }
    3. B001WTKE02
      Text in Illustration
      *a Claw

      Temporarily put the oil cooler assembly on the radiator support.

      Note

      Securely attach the 2 claws of the oil cooler assembly into the holes of the radiator support.

    4. Install the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL TRANSMISSION OIL COOLER AIR DUCT


    1. B001VYG

      Install the transmission oil cooler air duct with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  3. INSTALL OIL COOLER TUBE


    1. B001XDKN01

      Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL INLET NO. 4 OIL COOLER HOSE


    1. B001ZZHC01
      *a Paint Mark
      *b 0 to 3.0 mm (0 to 0.118 in.)
      *c 2.0 to 7.0 mm (0.0788 to 0.275 in.)

      Install the inlet No. 4 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each hose clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  5. INSTALL INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE


    1. B001YF3C01
      *a 0 to 3.0 mm (0 to 0.118 in.)
      *b 2.0 to 7.0 mm (0.0788 to 0.275 in.)

      Install the inlet No. 2 oil cooler hose and inlet No. 3 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each hose clip is facing the direction shown in the illustration.

  6. INSTALL INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE


    1. B001WVUC01
      *a Paint Mark
      *b 0 to 3.0 mm (0 to 0.118 in.)
      *c 2.0 to 7.0 mm (0.0788 to 0.275 in.)

      Install the inlet No. 1 oil cooler hose and outlet No. 1 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.

      Note

      Make sure the pinching portion of each hose clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

    2. Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.

  7. INSTALL TRANSMISSION OIL COOLER HOSE

    B001VMUC01
    *a RH Side
    *b Paint Mark

    1. Install the 2 transmission oil cooler hoses, and slide the 4 hose clips to secure the hose as shown in the illustration.

      Note


      • Make sure the pinching portion of each hose clip is facing the direction shown in the illustration.

      • Make sure the paint mark of each hose is facing outward.

  8. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  9. INSTALL FRONT UPPER CENTER BUMPER RETAINER

    Click here

  10. INSTALL FRONT FENDER APRON TRIM PACKING C

    Click here

  11. INSTALL FRONT FENDER APRON TRIM PACKING A

    Click here

  12. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  13. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  15. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here