AUTOMATIC TRANSMISSION UNIT DISASSEMBLY

PROCEDURE


  1. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

    A01X14S

    1. Remove the nut, spring washer and control shaft lever.

  2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    A01XAN3

    1. Using a screwdriver, bend the tabs of the lock washer.

    2. Remove the nut, lock washer and bolt.

    3. Remove the park/neutral position switch.

      Tech Tips

      Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.

  3. REMOVE SPEED SENSOR

    A01X85G

    1. Remove the 2 bolts and 2 speed sensors.

    2. Remove the 2 O-rings from the sensors.

  4. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)

    Click here

  5. REMOVE OIL COOLER TUBE UNION (w/o ATF Warmer)

    A01X9ZZ

    1. Remove the 2 oil cooler tube unions.

    2. Remove the 2 O-rings from the oil cooler tube unions.

  6. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

    A01XBO7

    1. Remove the 2 bolts.

    2. Remove the breather tube.

    3. Remove the O-ring from the tube.

  7. REMOVE AUTOMATIC TRANSMISSION HOUSING


    1. A01XAM0E01
      Text in Illustration
      *A for 1VD-FTV
      *B for 1UR-FE, 3UR-FE

      Remove the 14 bolts.

    2. Remove the transmission housing.

  8. REMOVE REAR TRANSFER ADAPTER

    A01X8J9

    1. Remove the 10 bolts.

    2. Remove the rear transfer adapter.

      Tech Tips

      Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear transfer adapter.

  9. REMOVE TRANSMISSION CASE ADAPTER OIL SEAL

    A01X9VSE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, pry out the oil seal.

      Note

      Be careful not to damage the rear transfer adapter.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

  10. REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING

    A01X5I5E01

    1. Using a screwdriver, remove the snap ring.

    2. Using SST and a press, press out the bearing.

      SST
      09950-60010   ( 09951-00650 )
      09950-70010   ( 09951-07150 )

  11. SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

    A01X6AZ

    1. Install the transmission case to an overhaul attachment.

  12. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    A01X7RN

    Note

    Do not turn the transmission over as this will contaminate the valve body with foreign matter from the bottom of the pan.


    1. Remove the drain plug, 12 bolts, oil pan and gasket.

    2. Remove the 4 magnets.

  13. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

    Click here

  14. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

    A01X960

    1. Turn over the transmission.

    2. Remove the 4 bolts and oil strainer from the valve body oil strainer assembly.

    3. Remove the O-ring from the valve body oil strainer assembly.

  15. REMOVE NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE

    A01X4E6

    1. Remove the 2 bolts and 2 temperature sensor clamps.

    2. Disconnect the 2 ATF temperature sensors.

    3. Disconnect the 9 connectors from the solenoid valves.

    4. A01XBAF

      Remove the 2 bolts and pull the No. 1 and No. 2 transmission wires out of the transmission case.

    5. A01X3HZ

      Remove the 2 O-rings from the transmission wires.

  16. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    1. Remove the bolt, detent spring cover and detent spring.

    2. A01WZBM

      Remove the 19 bolts.

    3. Remove the valve body assembly.

  17. REMOVE TRANSMISSION CASE GASKET

    A01X6PI

    1. Remove the 3 gaskets.

  18. REMOVE BRAKE DRUM GASKET

    A01XBSA

    1. Remove the 3 gaskets.

  19. REMOVE CHECK BALL BODY

    A01X7WGE04
    Text in Illustration
    *1 Check Ball Body
    *2 Spring

    1. Remove the check ball body and spring.

  20. REMOVE C-2 ACCUMULATOR PISTON

    A01XC50

    1. While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.

      Note

      Be careful as the B-3 accumulator pistons may jump out.

    2. Remove the 2 O-rings from the piston.

  21. REMOVE B-3 ACCUMULATOR PISTON

    A01X3EQ

    1. While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.

    2. Remove the 2 O-rings from the piston.

  22. REMOVE C-3 ACCUMULATOR PISTON

    A01X5ZM

    1. While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.

    2. Remove the 2 O-rings from the piston.

  23. REMOVE B-1 ACCUMULATOR VALVE

    A01X9DW

    1. Remove the B-1 accumulator valve and 2 springs.

  24. REMOVE PARKING LOCK PAWL BRACKET

    A01X28K

    1. Remove the 3 bolts and bracket.

  25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

    A01X966

    1. Disconnect the parking lock rod from the manual valve lever sub-assembly.

  26. REMOVE PARKING LOCK PAWL

    A01X75R

    1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

    2. Remove the E-ring from the shaft.

  27. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

    A01X3BY

    1. Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.

    2. A01X01E

      Using a pin punch and hammer, tap out the spring pin.

      Tech Tips

      Slowly tap out the spring pin so that it does not fall into the transmission case.

    3. Pull the manual valve lever shaft out through the transmission case and remove the manual valve lever sub-assembly.

  28. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

    A01X2YSE02
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, pry out the 2 oil seals.

      Note

      Be careful not to damage the transmission case.

      Tech Tips

      Wrap the tip of the screwdriver with protective tape before use.

  29. REMOVE OIL PUMP ASSEMBLY

    A01X1D0

    1. Remove the 10 bolts.

    2. A01XAYXE01

      Using SST, pull out the oil pump.

      SST
      09950-40011   ( 09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031 )
    3. A01X9US

      Remove the O-ring and 2 thrust bearing races from the oil pump.

  30. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

    A01XABX

    1. Remove the clutch drum and input shaft assembly from the transmission case.

    2. A01X8Z0

      Remove the clutch drum thrust washer and 2 thrust needle roller bearings.

  31. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

    Click here

  32. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

    A01XBO3

    1. Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.

  33. SECURE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    1. A01X7RFE02
      Text in Illustration
      *1 Torque Converter
      *2 Oil Pump

      Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.

  34. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

    A01X1PU

    1. Using a screwdriver, remove the snap ring.

    2. A01X2BH

      Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.

  35. REMOVE REAR CLUTCH DISC SET


    1. for 1VD-FTV:

      Remove the cushion plate, reverse clutch flange, 4 discs and 3 plates from the reverse clutch hub.

    2. for 1UR-FE, 3UR-FE

      Remove the cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.

    3. A01XBDF

      Remove the flange from the clutch drum.

    4. A01X3OBE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the clutch drum.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

  36. INSPECT REAR CLUTCH DISC

    Click here

  37. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

    Click here

  38. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

    A01XC1S

    1. Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.

  39. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

    Click here

  40. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

    A01XBAW

    1. Remove the 2 thrust needle roller bearings, the coast clutch hub with the No. 4 1-way clutch assembly, and the thrust bearing race from the clutch drum.

  41. INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY

    Click here

  42. REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY

    A01X1EC

    1. Separate the No. 4 1-way clutch assembly from the coast clutch hub.

    2. Remove the No. 2 clutch hub thrust washer from the coast clutch hub.

  43. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET

    A01X27EE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the forward clutch piston.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

    2. Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.

  44. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

    Click here

  45. REMOVE COAST CLUTCH DISC SET

    A01X26ME01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, remove the snap ring.

      Note

      Be careful not to damage the forward clutch piston.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

    2. for 1VD-FTV:

      Remove the coast clutch flange, 5 discs and 5 plates from the input shaft.

    3. for 1UR-FE, 3UR-FE

      Remove the coast clutch flange, 4 discs and 4 plates from the input shaft.

  46. INSPECT COAST CLUTCH DISC

    Click here

  47. REMOVE INPUT SHAFT SUB-ASSEMBLY

    A01X46X

    1. Remove the input shaft from the clutch drum.

  48. REMOVE INPUT SHAFT OIL SEAL RING

    A01WZBR

    1. Remove the 4 oil seal rings from the input shaft.

  49. REMOVE COAST CLUTCH PISTON

    A01X5TLE01

    1. Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.

      SST
      09350-30020   ( 09350-07040 )

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )
    3. A01X942

      Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.

    4. A01XAJZ

      Remove the O-ring from the No. 1 clutch balancer.

    5. A01X0FO

      Hold the input shaft by hand and apply compressed air to the input shaft to remove the coast clutch piston.

  50. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

    Click here

  51. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

    A01X851

    1. Hold the input shaft by hand and apply compressed air to the input shaft to remove the forward clutch piston.

    2. A01X5UO

      Remove the O-ring from the input shaft.

  52. REMOVE NO. 3 CLUTCH BALANCER

    A01XBIME01

    1. Place SST on the No. 3 clutch balancer and compress the reverse clutch return spring with a press.

      SST
      09380-60010   ( 09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080 )

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )

    3. Remove the No. 3 clutch balancer.

    4. A01XAPV

      Remove the reverse clutch return spring and O-ring from the reverse clutch piston.

  53. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

    Click here

  54. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

    A01X5FX

    1. Remove the reverse clutch piston from the clutch drum.

    2. A01X476

      Remove the O-ring from the reverse clutch piston.

    3. A01X0HB

      Remove the O-ring from the clutch drum.

  55. REMOVE DIRECT CLUTCH DISC SET

    A01X7OLE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, remove the snap rings from the clutch drum.

      Note

      Be careful not to damage the clutch drum.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

    2. for 1VD-FTV:

      Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.

    3. for 1UR-FE, 3UR-FE

      Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.

  56. INSPECT DIRECT CLUTCH DISC

    Click here

  57. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

    A01X56DE01

    1. Place SST on the direct clutch piston and compress the direct clutch return spring with a press.

      SST
      09380-60010   ( 09381-06030, 09381-06040, 09381-06080 )

    2. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07070 )

    3. Place the oil pump onto the torque converter, and then place the clutch drum onto the oil pump.

    4. A01X16IE01
      Text in Illustration
      *1 Oil Hole

      Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.

    5. A01X75S

      Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.

    6. A01X4W5

      Remove the 2 O-rings from the direct clutch piston.

  58. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

    Click here

  59. REMOVE NO. 3 BRAKE SNAP RING

    A01X7TYE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.

      Note

      Be careful not to damage the transmission case.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

  60. REMOVE NO. 3 BRAKE DISC SET


    1. Remove the 2 flanges, 4 discs and 3 plates from the transmission case.

  61. INSPECT NO. 3 BRAKE DISC

    Click here

  62. REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

    A01XA6SE01

    1. Using SST, remove the snap ring.

      SST
      09350-30020   ( 09350-07060 )

  63. REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    A01X1X4

    1. Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.

  64. REMOVE NO. 3 BRAKE PISTON

    A01X1VJE01

    1. Using SST and a press, compress the No. 3 brake piston return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

      SST
      09380-60010   ( 09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110 )
    2. A01X1T5

      Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.

    3. A01WZDR

      Remove the 2 O-rings from the No. 3 brake piston.

  65. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    Click here

  66. REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

    A01X15A

    1. Remove the 1-way clutch assembly with 1-way clutch inner race from the transmission case.

  67. INSPECT 1-WAY CLUTCH ASSEMBLY

    Click here

  68. REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

    A01XA1B

    1. Separate the 1-way clutch inner race from the 1-way clutch assembly and remove the No. 1 planetary carrier thrust washer.

  69. REMOVE FRONT PLANETARY GEAR ASSEMBLY

    A01X6I0

    1. Remove the front planetary gear assembly and thrust needle roller bearing from the transmission case.

    2. A01X8TW

      Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear assembly.

  70. INSPECT FRONT PLANETARY GEAR ASSEMBLY

    Click here

  71. REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

    A01X9M2

    1. Remove the front planetary ring gear together with the front planetary ring gear flange and center planetary ring gear from the transmission case.

    2. Remove the thrust needle roller bearing and thrust bearing race.

  72. REMOVE FRONT PLANETARY RING GEAR

    A01X5F7

    1. Using a screwdriver, remove the snap ring.

    2. A01X9GR

      Remove the front planetary ring gear from the center planetary ring gear.

  73. REMOVE CENTER PLANETARY RING GEAR

    A01X274

    1. Using a screwdriver, remove the snap ring.

    2. A01XAOS

      Remove the center planetary ring gear from the front planetary ring gear flange.

  74. REMOVE NO. 1 BRAKE DISC SET


    1. Remove the flange, 4 discs and 4 plates from the transmission case.

  75. INSPECT NO. 1 BRAKE DISC

    Click here

  76. REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

    A01X4TLE01

    1. Place SST on the brake piston return spring and compress the brake piston return spring.

      SST
      09380-60010   ( 09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120 )

    2. Using a screwdriver, remove the snap ring from the transmission case.

      Text in Illustration
      *1 Protective Tape

      Note

      Be careful not to damage the transmission case.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

    3. A01X1B4

      Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.

  77. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    Click here

  78. REMOVE NO. 1 BRAKE PISTON

    A01WYXH

    1. Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. A01X1E3

      Remove the 2 O-rings from the No. 1 brake piston.

  79. REMOVE CENTER PLANETARY GEAR ASSEMBLY

    A01X2OQ

    1. Remove the center planetary gear assembly and center planetary sun gear from the transmission case.

  80. INSPECT CENTER PLANETARY GEAR ASSEMBLY

    Click here

  81. REMOVE NO. 2 BRAKE DISC SET

    A01WYVDE03
    Text in Illustration
    *1 Protective Tape

    1. Place SST on the flange and compress the No. 2 brake piston return spring.

      SST
      09380-60010   ( 09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120 )

    2. Using a screwdriver, remove the snap ring from the transmission case.

      Note

      Be careful not to damage the transmission case.

      Tech Tips

      Wrap the tip of the screwdriver with tape.

    3. Remove the No. 2 brake flange, flange, 4 discs, 3 plates and No. 2 brake piston return spring from the transmission case.

  82. INSPECT NO. 2 BRAKE DISC

    Click here

  83. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

    Click here

  84. REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

    A01X61G

    1. Remove the No. 2 brake cylinder together with the No. 2 brake piston from the transmission case.

  85. REMOVE NO. 2 BRAKE PISTON

    A01X9FV

    1. Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    2. A01X71E

      Remove the 2 O-rings from the No. 2 brake piston.

  86. REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

    A01X1OXE03

    1. Using SST, remove the snap ring from the transmission case.

      SST
      09350-30020   ( 09350-07060 )
    2. A01X2O8

      Remove the intermediate shaft with No. 3 1-way clutch assembly, rear planetary ring gear flange and rear planetary ring gear from the transmission case.

  87. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

    Click here

  88. REMOVE 1-WAY CLUTCH INNER RACE

    A01X0U4

    1. Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.

  89. REMOVE REAR PLANETARY RING GEAR

    A01X20U

    1. Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.

    2. A01X79L

      Using a screwdriver, remove the snap ring.

    3. Remove the rear planetary ring gear flange from the rear planetary ring gear.

  90. INSPECT INTERMEDIATE SHAFT

    Click here

  91. REMOVE NO. 4 BRAKE DISC SET


    1. Remove the No. 4 brake flange, flange, 7 No. 4 brake discs and 6 plates from the transmission case.

  92. INSPECT NO. 4 BRAKE DISC

    Click here

  93. REMOVE BRAKE PLATE STOPPER SPRING

    A01X859

    Note

    When removing the brake plate stopper spring, do not apply excessive force and do not deform it.

  94. REMOVE REAR PLANETARY GEAR ASSEMBLY

    A01X4W6

    1. Remove the rear planetary gear assembly from the transmission case.

    2. A01WZ3V

      Remove the 2 thrust needle roller bearings from the rear planetary gear assembly.

    3. A01WZWC

      Remove the thrust bearing race from the transmission case.

  95. INSPECT REAR PLANETARY GEAR ASSEMBLY

    Click here

  96. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

    A01X5CWE01

    1. Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.

      SST
      09380-60010   ( 09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050 )

    2. Using SST, remove the snap ring and 1st and reverse brake return spring.

      SST
      09350-30020   ( 09350-07070 )
    3. A01X10L

      Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

      Tech Tips

      If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

    4. A01X14H

      Remove the 3 O-rings from the 1st and reverse brake piston.

  97. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

    Click here