TRANSMISSION WIRE INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION WIRE


    1. Coat the 2 new O-rings with automatic transmission fluid.

    2. Install the 2 O-rings to the No. 1 transmission wire and No. 2 transmission wire.

    3. B001VQE

      Install the No. 1 transmission wire and No. 2 transmission wire with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Note


      • When reusing the transmission wire, inspect the O-ring.

      • Make sure that the O-ring is not cracked or jammed when installing the transmission wire.

    4. B001XPN

      Connect the No. 2 transmission wire connector and No. 1 transmission wire connector.

      Tech Tips

      Push up the lever until the claw of the transmission wire connector makes a connection sound.

  2. CONNECT TRANSMISSION WIRE

    B001WDNE02
    Text in Illustration
    *a Orange
    *b Blue

    1. Connect the 9 connectors to the solenoid valves.

    2. Coat the 2 new O-rings with ATF and install them to the 2 ATF temperature sensors.

    3. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

      Torque:
      for bolt A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for bolt B
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips

      Each bolt length is indicated below.

      12 mm (0.472 in.) for bolt A

      36 mm (1.41 in.) for bolt B

  3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

    B001Z0S

    1. Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. Install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. B001Z7YE04
      Text in Illustration
      *1 Transmission Oil Cleaner Magnet

      Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.

    2. B001WFP
      Text in Illustration
      *1 Sleeve
      *2 Protrusion
      *a Correct
      *b Incorrect

      Install a new automatic transmission oil pan gasket and the automatic transmission oil pan subassembly with the 12 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note

      B001WPEE02

      • Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.

      • Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.

      • Make sure that the 12 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.

      • When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between a sleeve and the seal surface of the automatic transmission case sub-assembly.

  5. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  6. INSTALL OIL PAN PROTECTOR ASSEMBLY RH (w/ DPF)

    Click here

  7. INSTALL OIL PAN PROTECTOR ASSEMBLY LH (w/ DPF)

    Click here

  8. INSTALL OIL PAN PROTECTOR ASSEMBLY (w/o DPF)

    Click here

  9. INSTALL NO. 2 ENGINE UNDER COVER

    Click here