OIL COOLER INSTALLATION

PROCEDURE


  1. INSTALL OIL COOLER ASSEMBLY

    A01X91CE02
    *1 Lower Side
    *2 Outward

    1. Connect the oil cooler inlet hose and outlet hose.

    2. Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }
    3. A01XB30E02
      *a Claw

      Temporarily put the oil cooler on the radiator support.

      Note

      Securely attach the 2 claws of the oil cooler into the holes of the radiator support.

    4. Install the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL TRANSMISSION OIL COOLER AIR DUCT


    1. Install the oil cooler air duct with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  3. INSTALL OIL COOLER TUBE SUB-ASSEMBLY

    A01X7V5E02

    1. Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. CONNECT INLET NO. 4 OIL COOLER HOSE

    A01X4WFE02
    *1 Paint Mark

    1. Connect the inlet oil cooler hose as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  5. CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE

    A01X2P0

    1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  6. CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE

    A01X26SE02
    *1 Paint Mark

    1. Connect the 2 oil cooler hoses as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

    2. Pass the hose through the flexible hose clamp and close the clamp shown in the illustration.

  7. CONNECT TRANSMISSION OIL COOLER HOSE

    A01X85VE02
    *1 RH Side
    *2 Paint Mark

    1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

      Note

      Make sure the pinching portion of each clip is facing the direction shown in the illustration.

  8. ADD AUTOMATIC TRANSMISSION FLUID


    1. Add automatic transmission fluid Click here.

  9. INSTALL FRONT UPPER CENTER BUMPER RETAINER

    for Standard: Click here

    w/ Winch: Click here

  10. INSTALL FRONT FENDER APRON TRIM PACKING C

    Click here

  11. INSTALL FRONT FENDER APRON TRIM PACKING A

    Click here

  12. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  13. INSTALL NO. 1 ENGINE UNDER COVER

    Click here

  14. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  15. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here