VALVE BODY ASSEMBLY INSPECTION

PROCEDURE

1. INSPECT SHIFT SOLENOID VALVE SR

   

   *1	Shift Solenoid Valve SR:

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Solenoid Connector (SR) - Solenoid Body (SR) 20°C (68°F) 11 to 15 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) → Shift solenoid valve SR connector Battery negative (-) → Shift solenoid valve SR body Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

2. INSPECT SHIFT SOLENOID VALVE SLU

   

   *a	Component without harness connected: (Shift Solenoid Valve SLU)

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 of shift solenoid valve SLU - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) with a 21 W bulb → Terminal 2 Battery negative (-) → Terminal 1 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

3. INSPECT SHIFT SOLENOID VALVE SL2

   

   *a	Component without harness connected: (Shift Solenoid Valve SL2)

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 of shift solenoid valve SL2 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) with a 21 W bulb → Terminal 1 Battery negative (-) → Terminal 2 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

4. INSPECT SHIFT SOLENOID VALVE SLT

   

   *a	Component without harness connected: (Shift Solenoid Valve SLT)

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 of shift solenoid valve SLT - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) with a 21 W bulb → Terminal 2 Battery negative (-) → Terminal 1 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

5. INSPECT SHIFT SOLENOID VALVE SL1

   

   *a	Component without harness connected: (Shift Solenoid Valve SL1)

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Terminal 1 of shift solenoid valve SL1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) with a 21 W bulb → Terminal 1 Battery negative (-) → Terminal 2 Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

6. INSPECT SHIFT SOLENOID VALVE S1

   

   *1	Shift Solenoid Valve S1:

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Solenoid Connector (S1) - Solenoid Body (S1) 20°C (68°F) 11 to 15 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) → Shift solenoid valve S1 connector Battery negative (-) → Shift solenoid valve S1 body Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.

7. INSPECT SHIFT SOLENOID VALVE S2

   

   *1	Shift Solenoid Valve S2:

   
   

   1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Solenoid Connector (S2) - Solenoid Body (S2) 20°C (68°F) 11 to 15 Ω

   2. Apply 12 V of battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition Battery positive (+) → Shift solenoid valve S2 connector Battery negative (-) → Shift solenoid valve S2 body Valve moves and makes an operating noise

      If the result is not as specified, replace the solenoid valve.