Click here

CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) Check Bus 3 Line for Short to GND

Click here
Click here
DTC Code DTC Name
  Check Bus 3 Line for Short to GND
Click here

DESCRIPTION

There may be a short circuit between one of the CAN bus wires and GND when no resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

Detection Item Trouble Area
No resistance exists between terminal 6 (CA3H) of the central gateway ECU and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU and terminal 4 (CG) of the DLC3.

  • Short to GND in bus 3 CAN main wires

  • Short to GND in bus 3 CAN branch wires

  • Central gateway ECU

  • Multi-media module receiver assembly*1

  • Bus buffer ECU*2

  • Radio and display receiver assembly*3

  • No. 5 CAN junction connector

  • No. 6 CAN junction connector

  • No. 2 CAN junction terminal

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

Click here

PROCEDURE


  1. Click here

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU - NO. 5 CAN JUNCTION CONNECTOR)


    1. A01X3R5E02

      Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the central gateway ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E145-6 (CA3H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      E145-21 (CA3L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Table 1. Text in Illustration
      *a

      Front view of wire harness connector

      (to Central Gateway ECU)
      *b Front view of DLC3

  2. Click here

    CONNECT CONNECTOR


    1. Reconnect the E145 central gateway ECU connector.


  3. Click here

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 6 CAN JUNCTION CONNECTOR)


    1. A01X0I5E02

      Disconnect the No. 2 CAN junction terminal connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F98-3 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      F98-2 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Table 2. Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 2 CAN Junction Terminal)
      *b Front view of DLC3

    • OK

      REPLACE NO. 2 CAN JUNCTION TERMINAL

    • NGClick here
  4. Click here

    CONNECT CONNECTOR


    1. Reconnect the F98 No. 2 CAN junction terminal connector.


  5. Click here

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)


    1. A01X80RE01

      Disconnect the No. 5 CAN junction connector.

      Table 3. Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 5 CAN Junction Connector)

      		 *b Front view of DLC3
      *c to Central Gateway ECU *d to Bus Buffer ECU (w/ Bus Buffer ECU)
      *e

      • to Multi-media Module Receiver Assembly (for Multi-media Module Receiver Type)

      • to Radio and Display Receiver Assembly (for Radio and Display Type)

      		 *f to No. 6 CAN Junction Connector

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Connect to
      E152-8 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU
      E152-19 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      E152-9 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Bus buffer ECU*1
      E152-20 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      E152-10 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      • Multi-media module receiver assembly*2

      • Radio and display receiver assembly*3
      E152-21 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      E152-11 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 6 CAN junction connector
      E152-22 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher

      • *1: w/ Bus Buffer ECU

      • *2: for Multi-media Module Receiver Type

      • *3: for Radio and Display Type

      Table 4. Result
      Result Proceed to
      OK A
      NG (Central gateway ECU CAN main wire) B
      NG (No. 6 CAN junction connector CAN main wire) C
      NG (ECU or sensor CAN branch wires) D

    • A

      REPLACE NO. 5 CAN JUNCTION CONNECTOR

    • B

      REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

    • CClick here
    • DClick here
  6. Click here

    CONNECT CONNECTOR


    1. Reconnect the E152 No. 5 CAN junction connector.


  7. Click here

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)


    1. A01WZ5TE01

      Disconnect the No. 6 CAN junction connector.

      Table 5. Text in Illustration
      *a

      Rear view of wire harness connector

      (to No. 6 CAN Junction Connector)

      		 *b Front view of DLC3
      *c to No. 5 CAN Junction Connector *d to No. 2 CAN Junction Terminal

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition Connect to
      F99-6 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 5 CAN junction connector
      F99-17 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      F99-7 (CANH) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 CAN junction terminal
      F99-18 (CANL) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Table 6. Result
      Result Proceed to
      OK A
      NG (No. 5 CAN junction connector CAN main wire) B
      NG (No. 2 CAN junction terminal CAN main wire) C

    • A

      REPLACE NO. 6 CAN JUNCTION CONNECTOR

    • B

      REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

    • C

      REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

  8. Click here

    CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECU, SENSOR)


    1. A01X1XDE02

      Reconnect the CAN junction connector.

    2. Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to GND is connected.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E145-6 (CA3H) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      E145-21 (CA3L) - E22-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Table 7. Text in Illustration
      *a

      Component with harness connected

      (Central Gateway ECU)
      *b Front view of DLC3
      Tip:

      If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.


    • OK

      REPLACE CORRESPONDING ECU OR SENSOR

    • NG

      REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR