CAN COMMUNICATION SYSTEM(for RHD) Air Conditioning Amplifier Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode

Either condition is met:


  • "Air Conditioning Amplifier" is not displayed on "Bus Check".

  • "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" applies.

  • Power source or inside air conditioning amplifier assembly

  • Air conditioning amplifier assembly

  • Air conditioning amplifier assembly CAN branch wire or connector

WIRING DIAGRAM

A01X951E04

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.


    NEXT

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      For vehicle with an SRS system:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.


    NEXT

  3. CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)


    1. A01X4N9E01
      Text in Illustration
      *A w/ Rear Air Conditioning System
      *B w/o Rear Air Conditioning System
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Disconnect the E35*1 or E81*2 air conditioning amplifier assembly connector.


      • *1: w/ Rear Air Conditioning System

      • *2: w/o Rear Air Conditioning System

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/ Rear Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      E35-3 (CANH) - E35-4 (CANL) Ignition switch off 54 to 69 Ω
      w/o Rear Air Conditioning System
      Tester Connection Switch Condition Specified Condition
      E81-11 (CANH) - E81-12 (CANL) Ignition switch off 54 to 69 Ω

    NG

    REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

    OK

  4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)


    1. A01X1AUE01
      Text in Illustration
      *A w/ Rear Air Conditioning System
      *B w/o Rear Air Conditioning System
      *a

      Front view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Disconnect the E36*1 or E81*2 air conditioning amplifier assembly connector.


      • *1: w/ Rear Air Conditioning System

      • *2: w/o Rear Air Conditioning System

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/ Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E36-1 (GND) - Body ground Always Below 1 Ω
      E36-2 (E1) - Body ground Always Below 1 Ω
      w/o Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E81-14 (GND) - Body ground Always Below 1 Ω

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      w/ Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E36-6 (+B1) - Body ground Always 11 to 14 V
      E36-7 (+B2) - Body ground Always 11 to 14 V
      E36-5 (IG+) - Body ground Ignition switch ON 11 to 14 V
      w/o Rear Air Conditioning System
      Tester Connection Condition Specified Condition
      E81-21 (+B1) - Body ground Always 11 to 14 V
      E81-1 (IG+) - Body ground Ignition switch ON 11 to 14 V

    OK

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR