SIDE MONITOR SYSTEM, Diagnostic DTC:C1683, C1684

DTC Code DTC Name
C1683 Side Camera Feedback Malfunction
C1684 Side Camera Current Malfunction

DESCRIPTION

DTC C1683 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly (for Front Passenger Side) to the parking assist ECU.

DTC C1684 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the side television camera assembly (for Front Passenger Side) connected to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction

  • Harness or connector

  • Parking assist ECU

  • Side television camera assembly (for Front Passenger Side)

  • Outer rear view mirror assembly (for Front Passenger Side)
C1684 Side Camera Current Malfunction

WIRING DIAGRAM

A01X3DME01
for LHD
*a Side Television Camera Assembly
*b Outer Rear View Mirror Assembly RH
*c Parking Assist ECU
A01X3DME02
for RHD
*a Side Television Camera Assembly
*b Outer Rear View Mirror Assembly LH
*c Parking Assist ECU

CAUTION / NOTICE / HINT

Note


  • When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY AND BODY GROUND)


    1. Disconnect the F75 and F76 parking assist ECU connectors.

    2. Disconnect the I32*1 or I35*2 outer rear view mirror assembly (for Front Passenger Side) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F76-34 (SCV-) - I32-12 (SCV-) Always Below 1 Ω
      F76-10 (SCV+) - I32-1 (SCV+) Always Below 1 Ω
      F76-33 (SGND) - I32-13 (SGND) Always Below 1 Ω
      F76-32 (SCB+) - I32-2 (SCB+) Always Below 1 Ω
      F75-4 (GND1) - Body ground Always Below 1 Ω
      F76-34 (SCV-) - Body ground Always 10 kΩ or higher
      F76-10 (SCV+) - Body ground Always 10 kΩ or higher
      F76-33 (SGND) - Body ground Always 10 kΩ or higher
      F76-32 (SCB+) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F76-34 (SCV-) - I35-12 (DCV-) Always Below 1 Ω
      F76-10 (SCV+) - I35-1 (DCV+) Always Below 1 Ω
      F76-33 (SGND) - I35-13 (DGND) Always Below 1 Ω
      F76-32 (SCB+) - I35-2 (DCB+) Always Below 1 Ω
      F75-4 (GND1) - Body ground Always Below 1 Ω
      F76-34 (SCV-) - Body ground Always 10 kΩ or higher
      F76-10 (SCV+) - Body ground Always 10 kΩ or higher
      F76-33 (SGND) - Body ground Always 10 kΩ or higher
      F76-32 (SCB+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK PARKING ASSIST ECU (SCB+, SGND)


    1. Reconnect the F75 and F76 parking assist ECU connectors.

    2. A01X0EHE02
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F76-33 (SGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F76-32 (SCB+) - F76-33 (SGND) Engine switch on (IG), front and side monitor main switch assembly on 5.5 to 7.05 V

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

  3. CHECK SIDE TELEVISION CAMERA ASSEMBLY (SCV+, SGND OR DCV+, DGND)


    1. Reconnect the I32*1 or I35*2 outer rear view mirror assembly (for Front Passenger Side) connector.


      • *1: for LHD

      • *2: for RHD

      B001VLFE03
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      		 *b Waveform A
      *c Waveform B *d Synchronization Signal
      *e Video Waveform - -

      Tech Tips


      • A waterproof connector is used for the side television camera assembly (for Front Passenger Side). Therefore, inspect the waveform at the parking assist ECU with the connector connected.

      • The video waveform changes according to the image sent by the side television camera assembly (for Front Passenger Side).

    2. Measure the resistance according to the value(s) in the table below.

      OK
      Waveform is as shown in the illustration.
      Item Content
      Terminal No. (Symbol) F76-10 (SCV+) - F76-33 (SGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      • Waveform A: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is not covered, displaying an image

      • Waveform B: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is covered, blacking out the screen

    OK

    REPLACE PARKING ASSIST ECU Click here

    NG

  4. REPLACE SIDE TELEVISION CAMERA ASSEMBLY


    1. Replace the side television camera assembly (for Front Passenger Side) with a new or normally functioning one Click here.


    NEXT

  5. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      OK
      DTC C1683 or C1684 is not output.

    OK

    END (SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY Click here