PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) Image from Camera for Parking Assist Monitor is Abnormal

DESCRIPTION

The video signal from the rear television camera assembly is transmitted to the multi-media module receiver assembly.

WIRING DIAGRAM

A01X8XGE11
*a Multi-display Assembly
*b Rear Television Camera Assembly
*c Multi-media Module Receiver Assembly
*d GVIF Cable

CAUTION / NOTICE / HINT

Note


  • When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed Click here.

Tech Tips

Images may be unclear even in normal conditions if:


  • Noise may occur in the image during power back door operation (w/ Power Back Door System).

  • Electrical devices are used in the cabin (noise may occur in the image).

  • Accessories that generate radio waves have been installed (noise may occur in the image).

  • The outer mirror switch assembly is operated (noise may occur in the image).

  • The camera screen is frosted over (the image immediately after turning the ignition switch to ON may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • The rear television camera assembly lens is scratched.

  • The rear television camera assembly lens has drops of water on it or the humidity is high.

  • When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER - REAR TELEVISION CAMERA AND BODY GROUND)


    1. Disconnect the F77 multi-media module receiver assembly connector.

    2. Disconnect the S5 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F77-18 (V+) - S5-2 (CV+) Always Below 1 Ω
      F77-19 (V-) - S5-1 (CV-) Always Below 1 Ω
      F77-39 (CA+) - S5-4 (CB+) Always Below 1 Ω
      F77-40 (CGND) - S5-3 (CGND) Always Below 1 Ω
      F77-12 (GND1) - Body ground Always Below 1 Ω
      F77-18 (V+) - Body ground Always 10 kΩ or higher
      F77-19 (V-) - Body ground Always 10 kΩ or higher
      F77-39 (CA+) - Body ground Always 10 kΩ or higher
      F77-40 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CA+, CGND)


    1. A01X5ONE02
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Reconnect the multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F77-40 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F77-39 (CA+) - F77-40 (CGND) Engine switch on (IG), shift lever in R 5.5 to 7.05 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  3. CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)


    1. Reconnect the S5 rear television camera assembly connector.

      A01X5OQE02
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      		 *b Waveform A
      *c Waveform A *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips


      • A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.

      • The video waveform changes according to the image sent by the rear television camera assembly.

      Measurement Condition
      Item Content
      Tester No. (Symbol) F77-18 (V+) - F77-40 (CGND)
      Tool Setting 0.2 V/DIV., 50 μS/DIV
      Condition

      Waveform A: Engine starts, shift lever in R (camera lens is not covered, displaying an image)

      Waveform B: Engine starts, shift lever in R (camera lens is covered, blacking out the screen)
      OK
      Waveform is as shown in the illustration.

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    OK

  4. REPLACE HARNESS AND CONNECTOR (GVIF CABLE)


    1. Replace the harness and connector (GVIF cable) with a normally functioning one.


    NEXT

  5. CHECK PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System)


    1. Check if the same malfunction recurs when the parking assist monitor screen is displayed.

      OK
      Malfunction does not reoccur (returns to normal).

    OK

    END (GVIF CABLE IS DEFECTIVE) Click here

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here