CAMSHAFT REMOVAL

PROCEDURE


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE UPPER RADIATOR SUPPORT SEAL

    Click here

  5. REMOVE RADIATOR GRILLE

    Click here

  6. REMOVE FRONT BUMPER COVER

    Click here

  7. REMOVE TRANSMISSION OIL COOLER AIR DUCT

    Click here

  8. DISCONNECT RADIATOR SIDE DEFLECTOR LH

    Click here

  9. REMOVE FRONT FENDER MAIN SEAL LH

    Click here

  10. REMOVE FRONT FENDER MAIN SEAL RH

    Click here

  11. REMOVE FRONT WIPER ARM LH

    Click here

  12. REMOVE FRONT WIPER ARM RH

    Click here

  13. REMOVE HOOD TO COWL TOP SEAL

    Click here

  14. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  15. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  16. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here

  17. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  18. REMOVE NO. 2 ENGINE UNDER COVER

    Click here

  19. REMOVE FRONT FENDER APRON SEAL LH

    Click here

  20. REMOVE FRONT FENDER APRON SEAL FRONT RH

    Click here

  21. DRAIN ENGINE OIL

    Click here

  22. DRAIN ENGINE COOLANT

    Click here

  23. REMOVE V-BANK COVER SUB-ASSEMBLY

    Click here

  24. REMOVE AIR CLEANER HOSE ASSEMBLY

    Click here

  25. REMOVE AIR CLEANER ASSEMBLY

    Click here

  26. REMOVE NO. 1 RADIATOR HOSE

  27. REMOVE NO. 2 RADIATOR HOSE

  28. REMOVE FAN SHROUD

    Click here

  29. REMOVE RADIATOR ASSEMBLY

    Click here

  30. DISCONNECT ENGINE WIRE

    Click here

  31. DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

    Click here

  32. DISCONNECT COOLER COMPRESSOR ASSEMBLY

    Click here

  33. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

    Click here

  34. REMOVE OIL FILTER ELEMENT

    Click here

  35. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  36. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

    Click here

  37. REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

    Click here

  38. REMOVE NO. 1 OIL COOLER BRACKET

    Click here

  39. REMOVE OIL FILTER BRACKET

    Click here

  40. REMOVE INTAKE MANIFOLD

    Click here

  41. DISCONNECT VANE PUMP ASSEMBLY

    Click here

  42. DISCONNECT OIL COOLER PIPE ASSEMBLY

    Click here

  43. REMOVE GENERATOR ASSEMBLY

    Click here

  44. REMOVE NO. 1 WATER BY-PASS HOSE

    Click here

  45. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

    Click here

  46. REMOVE FRONT WATER BY-PASS JOINT

    Click here

  47. REMOVE NO. 2 ENGINE COVER

    Click here

  48. REMOVE NO. 1 ENGINE COVER

    Click here

  49. REMOVE WATER INLET HOUSING

    Click here

  50. REMOVE WATER PUMP PULLEY

    Click here

  51. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

    Click here

  52. REMOVE FLUID COUPLING BRACKET

    Click here

  53. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

  54. REMOVE IGNITION COIL ASSEMBLY

    Click here

  55. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

    Click here

  56. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

    Click here

  57. REMOVE SPARK PLUG TUBE GASKET

    Click here

  58. REMOVE CRANKSHAFT PULLEY

    Click here

  59. DISCONNECT WIRE HARNESS CLAMP BRACKET

    Click here

  60. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

    Click here

  61. REMOVE WATER INLET PIPE

    Click here

  62. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  63. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

    Click here

  64. REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH

    Click here

  65. REMOVE NO. 1 CHAIN VIBRATION DAMPER LH

    Click here

  66. REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH

    Click here

  67. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

    Click here

  68. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

    Click here

  69. REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH

    Click here

  70. REMOVE NO. 1 CHAIN VIBRATION DAMPER RH

    Click here

  71. REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH

    Click here

  72. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

    Click here

  73. REMOVE CRANKSHAFT TIMING GEAR KEY

    Click here

  74. REMOVE CAMSHAFT BEARING CAP LH


    1. B001W83E09
      Text in Illustration
      *1 IN
      *2 EX
      *3 Knock Pin

      Make sure that the knock pin of the camshaft is positioned as shown in the illustration.

    2. B001WJXE18

      Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

    3. B001XN1E08

      Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

      Note

      Uniformly loosen the bolts while keeping the camshaft level.

    4. Remove the 6 bearing caps.

      Tech Tips

      Arrange the removed parts in the correct order.

    5. Remove the No. 3 and No. 4 camshafts.

      Tech Tips

      Arrange the removed parts in the correct order.

  75. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    1. B001VPZ

      Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

      Tech Tips

      Tape the screwdriver tip before use.

  76. REMOVE CAMSHAFT BEARING CAP RH


    1. B001XCPE08
      Text in Illustration
      *1 EX
      *2 IN
      *3 Knock Pin

      Make sure that the knock pin of the camshaft is positioned as shown in the illustration.

    2. B001ZCCE16

      Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

    3. B001YVXE09

      Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

      Note

      Uniformly loosen the bolts while keeping the camshaft level.

    4. Remove the 6 bearing caps.

      Tech Tips

      Arrange the removed parts in the correct order.

    5. Remove the No. 1 and No. 2 camshafts.

      Tech Tips

      Arrange the removed parts in the correct order.

  77. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    1. B001YA0

      Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

      Note

      Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.

      Tech Tips

      Tape the screwdriver tip before use.