ECD SYSTEM(w/o DPF), Diagnostic DTC:P0504

DTC Code DTC Name
P0504 Brake Switch "A" / "B" Correlation

DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

Tech Tips

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

  • [OFF] denotes ground potential.

  • [ON] denotes battery potential (+B).

  • On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.

P0504
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Depress and release brake pedal with ignition switch ON

Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):

(a) Ignition switch ON.

(b) Brake pedal is released.

(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.

  • Open or short in stop light switch signal circuit

  • STOP fuse

  • IGN fuse

  • Stop light switch

  • ECM
Related Data List
DTC No. Data List
P0504 Stop Light Switch

WIRING DIAGRAM

A01X6K5E03

CAUTION / NOTICE / HINT

Tech Tips


  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

  • Stop light switch conditions can be checked using the GTS.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Engine and ECT / Data List / Stop Light Switch.

    5. Check Stop Light Switch when the brake pedal is depressed and released.

Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

Note


  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After replacing the ECM, the new ECM needs registration (See page ) and initialization Click here.

  • After replacing the fuel supply pump assembly, the ECM needs initialization Click here.

  • After replacing an injector assembly, the ECM needs registration Click here.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    1. A01XA8PE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the stop light switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A73-1 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY) Click here

    OK

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)


    1. A01X12FE01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stop Light Switch Assembly)

      Disconnect the stop light switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A73-5 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)


    1. Disconnect the stop light switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A70-3 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  4. CHECK ECM (STP AND ST1- VOLTAGE)

    A01X5WHE02
    Text in Illustration
    *A for LHD
    *B for RHD
    *a Brake Pedal Depressed
    *b Brake Pedal Released
    *c

    Front view of wire harness connector

    (ECM)

    1. Disconnect the ECM connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Brake Pedal Condition Specified Condition
      A38-35 (ST1-) - Body ground Released 11 to 14 V
      Depressed 0 to 3 V
      A38-13 (STP) - Body ground Released 0 to 3 V
      Depressed 11 to 14 V
      Standard Voltage
      for RHD
      Tester Connection Brake Pedal Condition Specified Condition
      A52-35 (ST1-) - Body ground Released 11 to 14 V
      Depressed 0 to 3 V
      A52-13 (STP) - Body ground Released 0 to 3 V
      Depressed 11 to 14 V

    4. Reconnect the ECM connector.


    OK

    REPLACE ECM Click here

    NG

  5. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)


    1. Disconnect the stop light switch assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A73-4 (L) - A38-35 (ST1-) Always Below 1 Ω
      A73-2 (L) - A38-13 (STP) Always Below 1 Ω
      A73-4 (L) or A38-35 (ST1-) - Body ground Always 10 kΩ or higher
      A73-2 (L) or A38-13 (STP) - Body ground Always 10 kΩ or higher
      Standard Resistance
      for RHD
      Tester Connection Condition Specified Condition
      A73-4 (L) - A52-35 (ST1-) Always Below 1 Ω
      A73-2 (L) - A52-13 (STP) Always Below 1 Ω
      A73-4 (L) or A52-35 (ST1-) - Body ground Always 10 kΩ or higher
      A73-2 (L) or A52-13 (STP) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. REPLACE STOP LIGHT SWITCH ASSEMBLY


    1. Replace the stop light switch assembly Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - STOP LIGHT SWITCH ASSEMBLY)


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY - STOP LIGHT SWITCH ASSEMBLY)


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  9. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the ignition switch off.

    4. Turn the ignition switch to ON and turn the GTS on.

    5. Depress and release the brake pedal.

    6. Enter the following menus: Engine and ECT / Trouble Codes.

    7. Confirm that the DTC is not output again.


    NEXT

    END