Click here

SFI SYSTEM, Diagnostic DTC:P0560

Click here
Click here
DTC Code DTC Name
P0560 System Voltage
Click here

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power source allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0560 Open in the ECM backup power source circuit (1 trip detection logic).

  • Open in backup power source circuit

  • Battery

  • Battery terminals

  • EFI MAIN NO. 1 fuse

  • ECM
Tip:

If DTC P0560 is stored, the ECM becomes unable to store some DTCs. Also, all DTCs and some of the data stored in the ECM are cleared every time the ignition switch is turned off.

A01X6RVE06
Table 2.
*a P/I-B
*b EFI MAIN NO.1
*c Integration Relay
*d Battery
Table 1. *a P/I-B *b EFI MAIN NO.1 *c Integration Relay *d Battery
Click here

WIRING DIAGRAM



Click here

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (ECM - BATTERY)


    1. Disconnect the ECM connector.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Table 3. for LHD
      Tester Connection Condition Specified Condition
      Battery positive terminal - A38-1 (BATT) Always Below 1 Ω
      Battery positive terminal or A38-1 (BATT) - Body ground Always 10 kΩ or higher
      Table 4. for RHD
      Tester Connection Condition Specified Condition
      Battery positive terminal - A52-1 (BATT) Always Below 1 Ω
      Battery positive terminal or A52-1 (BATT) - Body ground Always 10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reconnect the cable to the positive (+) battery terminal.


    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  2. Click here

    INSPECT BATTERY


    1. Check that the battery is not depleted.

      OK
      Battery is not depleted.

  3. Click here

    CHECK BATTERY TERMINAL


    1. Check that the battery terminals are not loose or corroded.

      OK
      Battery terminals are not loose or corroded.

    • OKClick here
    • NG

      REPAIR OR REPLACE BATTERY TERMINAL

  4. Click here

    CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs (Click here).

    4. Turn the ignition switch off and turn the GTS off.

    5. Start the engine and turn the GTS on.

    6. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    7. Read the DTCs.

      Table 5. Result
      Result Proceed to
      P0560 is output A
      No DTC is output B