OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. A01X5T5

      Remove the 2 bolts and No. 2 engine under cover seal.

    3. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

    5. Install the No. 2 engine under cover seal with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH


    1. A01WZR6

      Remove the 6 bolts and No. 1 engine under cover sub-assembly LH.

  4. REMOVE OIL FILTER ELEMENT


    1. A01XAESE01
      Text in Illustration
      *1 Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

    2. A01X3BG

      Remove the oil filter drain plug.

    3. A01X2HNE02
      Text in Illustration
      *1 Cap
      *2 Valve
      *3 Pipe
      *4 O-Ring
      *5 Hose

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A01XBXQ

      Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

    5. A01X8RCE04
      Text in Illustration
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A01X802E03
      Text in Illustration
      *1 Oil Filter Element
      *2 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.

  5. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, threads and O-ring groove.

    2. A01XB6GE01
      Text in Illustration
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

      Note


      • Do not remove the oil filter bracket clip.

      • Do not pinch the O-ring for the cap.

    6. A01XAS3E02
      Text in Illustration
      *1 Oil Filter Bracket Clip
      *2 Oil Filter Cap
      *3 O-Ring
      *4 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note


      • When tightening the oil filter cap, do not remove the oil filter bracket clip.

      • After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    7. A01X9RPE03
      Text in Illustration
      *1 O-Ring

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Be careful that the O-ring does not get caught between any surrounding parts.

  6. ADD ENGINE OIL


    1. Add fresh oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard Oil Capacity
      Item Specified Condition
      Drain and refill without oil filter change 7.1 liters (7.5 US qts, 6.2 Imp. qts)
      Drain and refill with oil filter change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
      Dry fill 9.3 liters (9.8 US qts, 8.2 Imp. qts)

  7. INSPECT ENGINE OIL LEVEL

    Click here

  8. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

  9. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH


    1. Install the No. 1 engine under cover with the 6 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  10. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here