БЛОК ДВИГАТЕЛЯ ПОВТОРНАЯ СБОРКА

PROCEDURE


  1. INSTALL STIFFENING CRANKCASE RING PIN

    B001LYKE06
    Text in Illustration
    *a Width
    *b Height
    *c Protrusion Height

    Note

    It is not necessary to remove a stiffening crankcase ring pin unless it is being replaced.


    1. Using a plastic hammer, tap in 2 new stiffening crankcase ring pins until they stop.

      Standard Ring Pin
      Item Protrusion Height Height Width
      Stiffening Crankcase Ring Pin 3.0 mm (0.118 in.) 8 mm (0.315 in.) 11 mm (0.433 in.)

  2. INSTALL STIFFENING CRANKCASE STUD BOLT

    B001MXRE02
    *1 9.0 mm (0.354 in.)
    *2 19 mm (0.748 in.)

    Note

    If a stiffening crankcase stud bolt is deformed or the threads are damaged, replace it.


    1. Using an E6 "TORX" socket wrench, install the stiffening crankcase stud bolts as shown in the illustration.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  3. INSTALL STIFFENING CRANKCASE ASSEMBLY


    1. B001L4XE07
      *1 2.0 to 3.0 mm
      *2 4.5 to 5.5 mm

      Apply seal packing in a continuous line as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent
      Standard Seal Diameter
      Area Specified Condition
      Continuous Line 2.0 to 3.0 mm (0.0787 to 0.118 in.)
      (A) 4.5 to 5.5 mm (0.177 to 0.217 in.)
      Application Length (A)
      56 mm (2.20 in.)

      Note


      • Remove any oil from the contact surfaces.

      • Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.

    2. B001NCCE02

      Install the stiffening crankcase assembly with the 11 bolts in the sequence shown in the illustration.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
      Bolt Length
      Item Specified Condition
      Bolt (A) 138 mm (5.43 in.)
      Bolt (B) 35 mm (1.38 in.)
      Bolt (C) 70 mm (2.76 in.)

    3. Recheck the torque for bolts (1) and (2).

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    4. Wipe off any excess seal packing with a clean piece of cloth.

  4. INSTALL OIL PUMP ASSEMBLY

    Click here

  5. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

    Click here

  6. INSTALL OIL PAN DRAIN PLUG


    1. B001LWL

      Install a new gasket and the oil pan drain plug.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  7. INSTALL REAR ENGINE OIL SEAL

    Click here

  8. INSTALL NO. 1 TAPER SCREW PLUG


    1. Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug, and install the No. 1 taper screw plug.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }
      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      Note


      • Install the No. 1 taper screw plug within 3 minutes of applying adhesive.

      • Do not start the engine within 1 hour of installing the No. 1 taper screw plug.

  9. INSTALL VENTILATION VALVE SUB-ASSEMBLY


    1. B001MSPE19
      Text in Illustration
      *1 Adhesive

      Apply adhesive to the threads of the ventilation valve sub-assembly.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

      Note


      • Install the ventilation valve sub-assembly within 3 minutes after applying seal packing.

      • Do not start the engine for at least 2 hours after installing the ventilation valve sub-assembly.

    2. B001L6M

      Install the ventilation valve sub-assembly.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  10. INSTALL CYLINDER HEAD GASKET

    Click here

  11. INSTALL CYLINDER HEAD SUB-ASSEMBLY

    Click here

  12. INSTALL VALVE STEM CAP


    1. Apply a light coat of engine oil to the valve stem ends.

    2. Install the 16 valve stem caps to the cylinder head sub-assembly.

      Note

      Do not drop the valve stem caps into the cylinder head sub-assembly.

  13. INSTALL VALVE LASH ADJUSTER ASSEMBLY


    1. Inspect each valve lash adjuster assembly before installing it Click here.

    2. Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

      Note

      Install the valve lash adjuster assembly to the same place it was removed from.

  14. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY


    1. B001LRWE16
      Text in Illustration
      *1 No. 1 Valve Rocker Arm Sub-assembly
      *2 Valve Lash Adjuster Assembly
      *3 Valve Stem
      *4 Valve Stem Cap

      Apply engine oil to the valve lash adjuster assembly tips and valve stem cap ends.

    2. Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.

  15. INSTALL CAMSHAFT HOUSING STRAIGHT PIN

    B001LMME02
    Text in Illustration
    *a Width
    *b Height
    *c Protrusion Height

    Note

    It is not necessary to remove a camshaft housing straight pin unless it is being replaced.


    1. Using a plastic hammer, tap in a new camshaft housing straight pin to the specified protrusion height.

      Standard Straight Pin
      Item Protrusion Height Height Width
      Camshaft Housing Straight Pin 6.5 to 7.5 mm (0.256 to 0.295 in.) 14 mm (0.551 in.) 6.0 mm (0.236 in.)

  16. INSTALL NO. 1 CAMSHAFT BEARING

    Click here

  17. INSTALL OIL CONTROL VALVE FILTER


    1. B001KTR

      Check that no foreign matter is on the mesh part of the oil control valve filter.

    2. Install the oil control valve filter.

      Note

      Do not touch the mesh when installing the oil control valve filter.

  18. INSTALL NO. 2 CAMSHAFT BEARING

    Click here

  19. INSTALL NO. 2 CAMSHAFT

    Click here

  20. INSTALL CAMSHAFT

    Click here

  21. INSTALL CAMSHAFT BEARING CAP

    Click here

  22. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

    Click here

  23. INSTALL CAMSHAFT TIMING SPROCKET

    Click here

  24. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

    Click here

  25. INSTALL CRANKSHAFT TIMING GEAR KEY


    1. B001LE4

      Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

      Tech Tips

      Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.

  26. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    1. B001MGO

      Install the No. 1 crankshaft position sensor plate with the "F" mark facing forward.

  27. INSTALL NO. 2 CHAIN SUB-ASSEMBLY

    Click here

  28. INSTALL CRANKSHAFT TIMING SPROCKET

    Click here

  29. INSTALL NO. 1 CHAIN VIBRATION DAMPER

    Click here

  30. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  31. INSTALL CHAIN SUB-ASSEMBLY

    Click here

  32. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  33. INSTALL CHAIN TENSIONER SLIPPER

    Click here

  34. INSTALL NO. 2 CHAIN VIBRATION DAMPER

    Click here

  35. INSTALL INLET WATER SUB-ASSEMBLY STUD BOLT

    Note

    If an inlet water sub-assembly stud bolt is deformed or the threads are damaged, replace it.


    1. B001KUNE03
      *1 21 mm (0.827 in.)
      *2 9 mm (0.354 in.)
      *3 34 mm (1.34 in.)

      Using an E5 "TORX" socket wrench, install the 2 inlet water sub-assembly stud bolts as shown in the illustration.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  36. INSTALL INLET WATER SUB-ASSEMBLY


    1. Type A:


      1. B001L4Z

        Install a new gasket and the water inlet sub-assembly with the bolt and 2 nuts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Type B:


      1. B001M85

        Install a new gasket and the water inlet sub-assembly with the 3 bolts.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  37. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

    Click here

  38. INSTALL TIMING CHAIN COVER OIL SEAL

    Click here

  39. INSTALL CRANKSHAFT PULLEY

    Click here

  40. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

    Click here

  41. INSTALL OIL FILTER UNION (for Oil Filter Sub-assembly Type)

    B001KX0

    1. Using a 12 mm hexagon socket wrench, install the oil filter union to the oil filter bracket.

      Torque:
      29.5 N*m  { 301 kgf*cm, 22 ft.*lbf }

  42. INSTALL OIL FILTER

    Click here

  43. INSTALL SPARK PLUG TUBE GASKET


    1. B001N3P

      Using a cutter knife, cut off the seal part of the removed spark plug tube gasket.

      Text in Illustration
      B001MUK Part to Cut Off
    2. B001N5DE04
      Text in Illustration
      *1 Spark Plug Tube Gasket without Sealing Part
      *2 New Spark Plug Tube Gasket

      Using a hammer and the spark plug tube gasket which has had the sealing part cut off, uniformly tap in a new spark plug tube gasket all the way.

      Note


      • Keep the lip free of foreign matter.

      • Do not tap in the spark plug tube gasket.

      Tech Tips

      If a spark plug tube gasket that will be used to install a new spark plug tube gasket is deformed, and cannot be positioned on a new spark plug tube gasket, correct the deformation using pliers.

    3. Return the claws of the ventilation baffle plate to their original positions.

  44. INSTALL CYLINDER HEAD COVER GASKET


    1. B001ME9E01
      Text in Illustration
      *1 Cylinder Head Cover Sub-assembly
      *2 Cylinder Head Cover Gasket

      Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

      Note


      • Remove any oil from the contact surfaces.

      • Misalignment between the center of the cylinder head cover sub-assembly rib and the center of the cylinder head cover gasket tab should be within 4.0 mm (0.157 in.).

  45. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY


    1. B001LMN

      Install 2 new gaskets to the camshaft bearing cap.

    2. B001LEL

      Apply seal packing as shown in the illustration.

      Seal Packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard Diameter
      4.0 mm (0.157 in.)

      Note


      • Remove any oil from the contact surfaces.

      • Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

      • Do not start the engine for at least 2 hours after the installation.

    3. B001NCL
      Text in Illustration
      *1 Timing Chain Cover Sub-assembly
      *2 Camshaft Housing Sub-assembly
      *3 Cylinder Head Cover Gasket

      Install the cylinder head cover sub-assembly with a new seal washer and the 13 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Misalignment between the contact surfaces of the timing chain cover sub-assembly and the camshaft housing sub-assembly and the center of the cylinder head cover gasket tab should be within 4.0 mm (0.157 in.).

      B001N8YE01

  46. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY


    1. B001KM0E19
      Text in Illustration
      *1 Adhesive

      Apply adhesive to 2 or 3 threads of the engine oil pressure switch assembly.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

      Note


      • Install the engine oil pressure switch assembly within 3 minutes after applying adhesive.

      • Do not start the engine within 1 hour after installation.

    2. B001MSW

      Using a 24 mm deep socket wrench, install the engine oil pressure switch assembly.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

  47. INSTALL ENGINE COOLANT TEMPERATURE SENSOR


    1. B001NAS

      Install a new gasket and the engine coolant temperature sensor.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  48. INSTALL KNOCK SENSOR


    1. B001KN2E01

      Install the knock sensor with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note

      Make sure that the knock sensor is in the correct position.

  49. INSTALL CRANKSHAFT POSITION SENSOR


    1. B001N2E

      Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    2. B001NCM

      Install the crankshaft position sensor with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  50. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    1. B001LS8

      Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.

    2. B001LT5

      Install the camshaft timing oil control valve assembly with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • Do not allow foreign matter to contact the oil seal face of the camshaft oil control valve assembly (connecting surface with cylinder head cover sub-assembly).

      • Be careful that the O-ring is not cracked or moved out of place when installing the camshaft timing oil control valve assembly.

  51. INSTALL CAMSHAFT POSITION SENSOR


    1. B001MXO

      Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    2. B001K9W

      Install the camshaft position sensor with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Make sure that the O-ring is not cracked or jammed when installing the camshaft position sensor.

  52. INSTALL SPARK PLUG

    Click here

  53. INSTALL ENGINE COVER JOINT BOLT


    1. B001LXZ

      Install the 3 engine cover joint bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  54. INSTALL WIRING HARNESS CLAMP BRACKET


    1. B001M1M

      Install the wiring harness clamp bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  55. INSTALL OIL FILLER CAP GASKET


    1. B001LPI

      Install the oil filler cap gasket to the oil filler cap sub-assembly.

  56. INSTALL OIL FILLER CAP SUB-ASSEMBLY


    1. B001KWM

      Install the oil filler cap sub-assembly.